17.040.20;25.220.40 标准查询与下载

DIN EN ISO 3543 Corrigendum 1:2006 金属涂料及其他无机涂料. 厚度测量. 贝特反向散射法（ISO 3542: 2000）; 英文版本DIN EN ISO 3542: 2001-12勘误表1

Metallic and other inorganic coatings - Measurement of thickness - Bete backscatter method (ISO 3542:2000) Corrigendum 1 to English version of DIN EN ISO 3542:2001-12

DIN EN ISO 3543 Berichtigung 1:2006 金属和其他无机物覆层.厚度测量.β背反射法(ISO 3543:2000).勘误到DIN EN ISO 3543:2001-12

This standard specifies a method for the non-destructive measurement of coating thicknesses using beta backscatter gauges.

Metallic and other inorganic coatings - Measurement of thickness - Beta backscatter method (ISO 3543:2000), Corrigenda to DIN EN ISO 3543:2001-12; German version EN ISO 3543:2000/AC:2006

LST EN 14571-2005 非金属基材料上的金属涂层 涂层厚度的测量 微电阻率法

Metallic coatings on nonmetallic basis materials - Measurement of coating thickness - Microresistivity method

LST EN 10318-2005 锌基和铝基金属镀层厚度和化学成分的测定常规方法

Determination of thickness and chemical composition of zinc- and aluminium-based metallic coatings - Routine method

DIN EN 10318:2005 锌和铝基金属涂层的厚度和化学成分的测定.常规法

This European standard specifies a glow discharge optical emission spectrometric method for the determination of thickness and chemical composition of metallic surface coatings consisting of zinc and aluminium based alloys. The alloying elements considered are aluminium, nickel, iron, silicon and lead.#,,#

Determination of thickness and chemical composition of zinc- and aluminium-based metallic coatings - Routine method; German version EN 10318:2005

BS EN ISO 2177:2005 金属覆层.覆层厚度的测量.阳极溶解库仑法

This International Standard describes a coulometric method, by anodic dissolution, for measuring the thickness of metallic coatings. It is only applicable to conductive coatings. Typical combinations of coatings and substrates that can be tested by this method are given in Table 1. Other combinations may be tested with electrolytes in current use (see Annex A), or new electrolytes may be developed for them but, in both cases, it is necessary to verify the suitability of the complete system. This International Standard is also applicable to multi-layer systems, e.g Cu-Ni-Cr (see also 8.5). It may be used to measure the thickness of coatings applied by various means, if due account is taken of special features such as the presence of an alloy layer. In some cases, the presence and thickness of diffusion layers can also be measured. It can also be used to measure the thickness of coatings on cylindrical specimens and wires (see 8.7).

Metallic coatings - Measurement of coating thickness - Coulometric method by anodic dissolution

DIN EN 14571:2005 非金属基底材料上的金属覆层.测量覆层厚度.微电阻率法

Metallic coatings on nonmetallic basis materials - Measurement of coating thickness - Microresistivity method; German version EN 14571:2005

BS EN 10318:2005 测定锌基和铝基金属覆层的厚度和化学成分.常规法

This European Standard specifies a glow discharge optical emission spectrometric method for the determination of the thickness and chemical composition of metallic surface coatings consisting of zinc and aluminium based alloys. The alloying elements considered are aluminium, nickel, silicon and lead. This method is applicable to zinc contents between 40 % (m/m) and 100 % (m/m); aluminium contents between 0,01 % (m/m) and 60 % (m/m); nickel contents between 0,01 % (m/m) and 15 % (m/m); silicon contents between 0,01 % (m/m) and 3 % (m/m); lead contents between 0,005 % (m/m) and 0,1 % (m/m).

Determination of thickness and chemical composition of zinc- and aluminium-based metallic coatings - Routine method

BS EN 14571:2005 非金属基底材料上的金属覆层.覆层厚度的测量.微电阻率法

This document describes a method for nondestructive measurements of the thickness of conductive coatings on nonconductive base materials. This method is based on the principle of the sheet resistivity measurement and is applicable to any conductive coatings and layers of metal and semiconductor materials. In general, the probe has to be adjusted to the conductivity and the thickness of the respective application. However, this document focusses on metallic coatings on nonconductive base materials (e.g. Copper on plastic substrates, printed circuit boards). NOTE 1 This method also applies to the measurement of through-hole copper thickness of printed circuit boards. However, for this application a probe geometry different from the one described in this document is necessary. NOTE 2 This method is also applicable for thickness measurements of conductive coatings on conductive base materials, if the resistivity of the coating and the base material is different. This case is not considered in this document.

Metallic coatings on nonmetallic basis materials - Measurement of coating thickness - Microresistivity method

EN 10318:2005 锌和铝基金属涂层的厚度和化学成分的测定.常规法

This European Standard specifies a glow discharge optical emission spectrometric method forThe determination of the thickness and chemical composition of metallic surface coatings consisting of zinc and aluminium based alloys.The alloying elements considered are aluminium, nickel, silicon and lead.This method is applicable to zinc contents between 40 % (m/m) and 100 % (m/m); aluminium contents between 0,01 % (m/m) and 60 % (m/m); nickel contents between 0,01 % (m/m) and 15 % (m/m); silicon contents between 0,01 % (m/m) and 3 % (m/m); lead contents between 0,005 % (m/m) and 0,1 % (m/m).

Determination of thickness and chemical composition of zinc- and aluminium-based metallic coatings - Routine method

EN 14571:2005 非金属基底材料上金属覆层.覆层厚度的测量.微电阻率法

This document describes a method for nondestructive measurements of the thickness of conductive coatings on nonconductive base materials.This method is based on the principle of the sheet resistivity measurement and is applicable to any conductive coatings and layers of metal and semiconductor materials. In general, the probe has to be adjusted to the conductivity and the thickness of the respective application. However,This document focusses on metallic coatings on nonconductive base materials (e. g. Copper on plastic substrates, printed circuit boards). NOTE 1This method also applies to the measurement of through-hole copper thickness of printed circuit boards. However, forThis application a probe geometry different from the one described inThis document is necessary. NOTE 2This method is also applicable for thickness measurements of conductive coatings on conductive base materials, if the resistivity of the coating and the base material is different.This case is not considered inThis document.

Metallic coatings on nonmetallic basis materials - Measurement of coating thickness - Microresistivity method

BS EN ISO 1463:2005 金属和氧化物覆层.覆层厚度的测定.显微镜法

This International Standard describes a method for the measurement of the local thickness of metallic coatings, oxide layers, and porcelain or vitreous enamel coatings, by the microscopical examination of cross-sections using an optical microscope. WARNING — The use of this document may involve the use of hazardous materials, operations and equipment. This document does not address any health hazard and safety issues associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to take suitable action to comply with any national and/or local regulations prior to its use.

Metallic and oxide coatings - Measurement of coating thickness - Microscopical method

NF A91-110:2004 金属和氧化物镀层.镀层厚度的测量.显微镜法

Metallic and oxide coatings - Measurement of coating thickness - Microscopical method.

LST EN ISO 2177:2004 金属涂层 涂层厚度的测量 阳极溶解库仑法（ISO 2177:2003）

Metallic coatings - Measurement of coating thickness - Coulometric method by anodic dissolution (ISO 2177:2003)

LST EN ISO 1463:2004 金属和氧化物涂层 涂层厚度的测量 显微镜法（ISO 1463:2003）

Metallic and oxide coatings - Measurement of coating thickness - Microscopical method (ISO 1463:2003)

DIN EN ISO 1463:2004 金属和氧化物镀层.镀层厚度的测定.显微镜法

This standard describes a method for the measurement of the local thickness of metallic coatings, oxide layers, and porcelain or vitreous enamel coatings, by the microscopical examination of cross-sections using an optical microscope.#,,#

Metallic and oxide coatings - Measurement of coating thickness - Microscopical method (ISO 1463:2003); German version EN ISO 1463:2004

DIN EN ISO 2177:2004 金属覆层.覆层厚度的测量.阳极溶解库仑法

This document specifies a coulometric method by anodic dissolution for measuring the thickness of metallic coatings.

Metallic coatings - Measurement of coating thickness - Coulometric method by anodic dissolution (ISO 2177:2003); German version EN ISO 2177:2004

EN ISO 1463:2004 金属和氧化物镀层.镀层厚度的测定.显微镜法 ISO 1463-2003

This International Standard describes a method forThe measurement of the local thickness of metalliccoatings, oxide layers, and porcelain or vitreous enamel coatings, byThe microscopical examination ofcross-sections using an optical microscope.

Metallic and oxide coatings - Measurement of coating thickness - Microscopical method (ISO 1463:2003)

EN ISO 2177:2004 金属覆盖层.覆盖层厚度的测量.阳极溶解库仑法 ISO 2177-2003

Metallic Coatings - Measurement of Coating Thickness - Coulometric Method by Anodic Dissolution

DIN EN ISO 3882:2003 金属和其他无机物覆层.厚度测量方法述评

Metallic and other inorganic coatings - Review of methods of measurement of thickness (ISO 3882:2003); German version EN ISO 3882:2003