21.120.10 轴 标准查询与下载

GB/T 9239.32-2017 机械振动 转子平衡 第32部分：轴与配合件平衡的键准则

GB/T 9239的本部分规定了用键连接的转子组件的单个零部件(轴和配合件)平衡的唯一准则。 旨在使所有被平衡的零部件具有适配性，以便它们在组装后能够满足转子组件整体的平衡允差和(或)振动限值的要求。 本部分规定了在平衡用键装配的转子组件的单个零部件时使用半键，它还规定了按所使用的键准则对所平衡部件的标记方法。 本部分适用于在平衡机上、在转子自身的轴承上或在现场平衡的转子。键准则也适用于测量尚未组装上配合件，且带有键槽的转子的剩余不平衡量和(或)振动量。 除了与轴的轴线平行安装的等截面的矩形或正方形平键之外，本部分也适用于安装在锥形轴上的键、半圆键、楔键、销和其他特殊的键。半键准则的原理还适用特殊形状的键和定位的专用键。

Mechanical vibration—Rotor balancing—Part32：Shaft and fitment key convention

GB/T 1570-2005 圆锥形轴伸

本标准规定了1：10圆锥形轴伸(以下简称圆锥形轴伸)的型式和尺寸。 本标准适用于一般机器之间的联结并传递运动和转矩的场合。

Conical shaft ends

GB/T 12217-2005 机器 轴高

本标准规定了主动和从动机器轴高的基本尺寸及其公差。 本标准适用于主动机器和从动机器。

Machines-Shaft heights

GB/T 1569-2005 圆柱形轴伸

本标准规定了圆柱形轴伸(以下简称轴伸)的直径和长度系列。 本标准适用于一般机器之间的联结并传递运动和转矩的场合。

Cylindrical shaft ends

GB/T 1570-1990 圆锥形轴伸

本标准规定了1：10圆锥形轴伸（以下简称圆锥形轴伸）的型式和尺寸。 本标准适用于一般机器之间的联结并传递转矩的场合。

Conical shaft ends

GB/T 1569-1990 圆柱形轴伸

本标准规定了圆柱形轴伸（以下简称轴伸）的直径和长度系列。 本标准适用于一般机器之间的联结并传递转矩的场合。

Cylindrical shaft ends

T/QGCML 1385-2023 汽车用花键轴

本文件规定了汽车用花键轴的术语定义、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于汽车用花键轴的生产和检验。（以下简称“花键轴”）

Automobile spline shaft

T/ZJDJ 001-2022 新能源汽车用驱动电机轴

　技术要求 一般要求 电机轴应符合本标准的规定,并按经规定程序批准的产品图样及技术文件制造。如有特殊需要时，按用户与制造厂的协议执行。 材料要求 优先推荐使用GB/T 3077-2015中的牌号为20CrMnTi、20CrNiMo、40Cr、42CrMo的合金钢或GB/T 5216-2004中牌号为20CrMnTiH、20CrNiMoH、40CrH、42CrMoH的合金钢。 热处理要求 4.3.1　低碳合金钢材质 预先热处理宜采用预先正火、退火热处理工艺。正火后硬度应为HB190～220、退火后硬度应不大于HRB80；带状组织应不大于2级,晶粒度不小于5级,若有球化退火其球化度不小于4级。 终极热处理宜采用终艺渗碳淬火、碳氮共渗热处理工艺。处理后表面硬度应为HRC58～63，表面组织针状马氏体及残奥组织应不大于4级；芯部硬度HRC30～45，低碳马氏体及铁素体不大于4级；有效硬化层宜为0.3～1.3mm，允许根据轴的强度扭矩自行确定。 4.3.2　中碳合金钢材质 预先热处理宜采用调质热处理工艺，调质后硬度应为HRC28～32，相应要求应符合表1规定。 终极热处理宜采用感应淬火工艺，处理后表面硬度应为HRC50～58，见硬层深度宜为0.5～5mm,允许根据轴的强度扭矩自行确定，相应要求应符合表2规定。 表1　预先热处理工艺相关要求 序号　材料　预先热处理工艺　硬度　备注 1　20CrMnTi　退火、正火　退火HRB

Motor shaft of new energy vehicle-Specifications

DIN 3689-1:2021 轴环连接 次摆线 H 型材 第1部分：几何形状和尺寸

This document defines the geometry and dimensions of hypotrochoidal connection profiles (H-profiles). The hypotrochoidal curves (H-profiles) offer technically interesting contours for modern positive shaft-hub connections. The characteristics of the H-profiles are the possibiliti

Shaft to collar connection - Hypotrochoidal H-profiles - Part 1: Geometry and dimensions

KS B 0406-2020 轴直径

Diameter of Shafts

ASTM A503/A503M-15(2020) 锻造曲轴的超声波检验标准规范

1.1 This is an acceptance specification for the ultrasonic inspection of forged steel crankshafts having main bearing journals or crankpins 4 in. [100 mm] or larger in diameter. 1.2 This specification covers the testing equipment required and the test procedure to be followed, and it defines the critical and noncritical areas and limits of acceptance. 1.3 This specification is intended to cover both continuous grain flow (CGF) crankshafts for medium and high speed diesel engines as well as solid (slab) forged crankshafts for other applications. 1.4 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standard. Within the text and tables, the SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 Unless the order specifies the applicable “M” specification designation, the inch-pound units shall be used. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Ultrasonic Examination of Forged Crankshafts

DIN 5481:2018 锯齿花键

Serration splines and constant gab angle of 60° with number of teeth from 28 to 42 in a nominal size of 7mm to 60mm are fixed.

Serration splines

GSO ISO 496:2015 旋转和从动设备 轴高度

  Scope is not provided for this standard

Driving and driven machines -- Shaft heights

JB/T 12510-2014 中厚钢板压力校平液压机

Medium thick steel plate pressure leveling hydraulic press

DIN 5480-2:2015-03 基于参考直径的渐开线花键. 第2部分: 标称和检验尺寸

Involute splines based on reference diameters - Part 2: Nominal and inspection dimensions

DIN 743-3 Berichtigung 1:2014 轴和柄负载能力的计算.第3部分:材料强度.勘误表

Calculation of load capacity of shafts and axles - Part 3: Strength of materials, Corrigendum to DIN 743-3:2012-12

SAE J501-2014 轴端

No Scope Available

Shaft Ends

KS B 6874-2013 凹版印刷机连接印版滚筒用锥体

Taper cone for connecting printing cylinder of gravure printing press

KS B 0408-2013 1/10 锥形轴端

1/10 Conical shaft ends

KS B ISO 496-2013 主动机和从动机 轴高

Driving and driven machines－Shaft heights