21.260 润滑系统 标准查询与下载

GB/T 38276-2019 润滑系统 术语和图形符号

Lubrication system—Terminology and graphical symbols

GB/T 38275-2019 润滑系统 检验规范

Lubrication system—Inspection specification

GB/T 38274-2019 润滑系统 能效评定方法

Lubrication system—Efficiency assessment method

GB/T 25969-2010 家用太阳能热水系统主要部件选材通用技术条件

本标准规定了家用太阳能热水系统主要部件的选材原则、技术要求、检验方法、检验规则。 本标准适用于贮热水箱容积不大于0.6m家用太阳能热水系统主要部件。

Specification of material selecting for main parts of domestic solar water heating system

GB/T 13608-2009 合理润滑技术通则

本标准规定了合理润滑的术语和定义、合理润滑设计、润滑剂产品供应、润滑剂使用和润滑剂报废及再利用等技术要求。 本标准适用于需要给予润滑的设备的设计与制造以及使用与管理；润滑剂生产；润滑剂的使用与管理；报废润滑剂的处理与再利用。

General principle for rational lubrication technology

GB/T 17186-1997 钢制管法兰连接强度计算方法

本标准规定了用于钢制管法兰的A、B两种强度法兰计算方法。 本标准的法兰计算方法A主要用于公称压力PN为2.0、5.0、11.0、15.0、26.0及42.0MPa的钢制管法兰。 本标准的法兰计算方法B主要用于公称压力PN为0.25、0.6、1.0、1.6、2.5及4.0MPa的钢制管法兰。

Calculating method for the strength of steel pipe flanged joint

GB/T 13608-1992 合理润滑技术通则

本标准规定了润滑技术合理化的技术要求和润滑技术采取合理化措施后的经济效益计算方法。 本标准适用于需要给予油脂润滑的设备和仪器仪表的设计与制造，也适用于设备和仪器仪表的使用及润滑剂的生产与贮运。

General principle for rational lubrication technology

GB/T 1156-1979 旋套式注油油杯 基本型式与尺寸

Sleeve type drip-feed lubricating cups--Types and dimensions

T/QGCML 976-2023 钢丝绳清洁润滑保养系统

本文件规定了钢丝绳清洁润滑保养系统（以下简称“系统”）的系统结构、基本参数、技术要求、试验方法、检验规则、标志、标签和使用说明书、包装、运输和贮存。 本文件适用于水电站、船、闸、港口、码头、矿山等多场合钢丝绳设备的清洁、润滑和保养。

Wire rope cleaning and lubrication maintenance system

T/QGCML 977-2023 开式齿轮喷射润滑系统

本文件规定了开式齿轮喷射润滑系统（以下简称“系统”）的术语和定义、系统结构、基本参数、技术要求、试验方法、检验规则、标志、标签和使用说明书、包装、运输和贮存。 本文件适用于电厂、矿山、冶金、建材、造纸等机械设备的开式齿轮副的润滑系统。

Open Gear Jet Lubrication System

KS B 2807-2022 重型润滑嘴

Heavy duty lubricating nipples

ASTM D7217-22 用高频线性振荡（SRV）试验机测定固体粘结薄膜的极限压力特性的标准试验方法

1.1 This test method covers a procedure for determining extreme pressure properties of solid bonded films under high-frequency linear-oscillation motion using the SRV test machine. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Extreme Pressure Properties of Solid Bonded Films Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

ASTM F1460/F1460M-18(2022) 油喷口扩散剂的标准应用规范

1.1 This practice covers uniform procedures for determining and reporting the dosage rate of oil spill dispersant application equipment. 1.2 This practice is applicable to spray systems employing booms and nozzles and is not fully applicable to other systems such as fire monitors, sonic distributors, or fan-spray guns. 1.3 This practice is applicable to systems for use on ships, boats, helicopters, or airplanes. 1.4 This practice is one of four related to dispersant application systems using booms and nozzles. One is on design, one on calibration, one on deposition, and one on the use of the systems. Familiarity with all four standards is recommended. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Calibrating Oil Spill Dispersant Application Equipment Boom and Nozzle Systems

ASTM F1413/F1413M-18(2022) 溢油分散剂应用设备的标准指南:吊杆和喷嘴系统

1.1 This guide covers design criteria, requirements, material characteristics, and essential features for oil spill dispersant application systems. This guide is not intended to be restrictive to a specific configuration. 1.2 This guide covers spray systems employing booms and nozzles and is not fully applicable to other systems such as fire monitors, sonic distributors, or fan-spray guns. 1.3 This guide covers systems for use on ships, boats, helicopters, or airplanes. 1.4 This guide is one of several related to dispersant application systems using booms and nozzles. One is on design, one on calibration, one on deposition measurements, and one on the use of the systems. Familiarity with all four guides is recommended. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Oil Spill Dispersant Application Equipment: Boom and Nozzle Systems

ASTM E2793-22 E274摩擦测量系统和设备的评估、校准和相关性的标准指南

1.1 This guide describes the evaluation, calibration, and correlation of Test Method E274/E274M friction measurement systems as conducted at an ISO 17025 accredited field test center (FTC).2 The evaluation, calibration, and correlation process, using the specialized equipment, facilities, surfaces, trained personnel, and area reference friction measurement systems (ARFMS) available at each FTC, are conducted using the procedures described below. 1.2 The FTC complies with the requirements of Guide E1890. Guide E1890 requires a more stringent calibration process and requires all ARFMS systems be correlated together once a year on three surfaces at three speeds with twelve repeats each for a total of 108 pairs. 1.3 This guide is offered as a process to identify and quantify the variables that affect system performance, to minimize the effect of these variables, and to provide a means to relate Test Method E274/E274M friction measurement systems to reference friction measurement systems. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Evaluation, Calibration, and Correlation of E274 Friction Measurement Systems and Equipment

FprEN 15427-1-1-2021 铁路应用 轮/轨摩擦管理 第 1-1 部分：设备和应用 法兰润滑剂

Railway applications - Wheel/Rail friction management - Part 1-1: Equipment and Application - Flange Lubricants

T/ZZB 2188-2021 机床润滑系统用齿轮式油脂润滑泵

本文件规定了机床润滑系统用齿轮式油脂润滑泵（以下简称“润滑泵”）术语和定义、基本要求、产品型号和基本参数、技术要求、试验方法、检验规则、标志、包装、运输、贮存以及质量承诺。 本文件适用机床润滑系统中用于输送公称压力不大于 4 MPa，流量不大于 500 mL/min，使用温度－20 ℃～+80 ℃，适用润滑脂锥入度介于 3 551/10 mm～4 701/10 mm 的带有压力开关并具有自动闭合功能的齿轮式油脂润滑泵。

Gear-grease lubrication pump for machine tool lubrication system

ASTM G204-21 微动条件下接触固体表面损伤的标准试验方法

1.1 This test method may be used for either fundamental or applications-oriented studies of fretting damage. Accordingly, data from these tests may be used to rank the wear resistance of candidate material couples for certain types of machine components whose service life is limited by fretting. 1.2 This test method uses a tribological bench test apparatus with a mechanism or device that will produce the necessary relative motion between a contacting hemispherical rider and a flat counterface. The rider is pressed against the flat counterface with a loading mass. The test method is intended for use in room temperature air. Other configurations or test parameters may be needed to investigate fretting in the presence of lubricants or other environments. 1.3 The purpose of this test method is to rub two solid surfaces together under controlled fretting conditions and to quantify the damage to both surfaces in units of volume loss. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Damage to Contacting Solid Surfaces under Fretting Conditions

ONR CEN/TS 15427-1-2-2021 铁路应用 轮/轨摩擦管理 第 1-2 部分：设备和应用 轨顶材料

Railway applications - Wheel/Rail friction management - Part 1-2: Equipment and Application - Top of Rail materials

DS/CEN/TS 15427-1-2:2021 铁路应用《轮轨摩擦管理》第 1-2 部分：设备与应用《轨道材料之巅》

Railway applications – Wheel/Rail friction management – Part 1-2: Equipment and Application – Top of Rail materials