23.040.01;75.200;83.140.30 标准查询与下载

ISO 16486-4:2016 供应气体燃料用塑料管系统. 带熔接连接和机械连接的未增塑聚酰胺 (PA-U) 管系统. 第4部分: 阀门

Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 4: Valves

ISO 16486-1:2012/Amd 1:2014 供应气体燃料用塑料管系统. 带熔接连接和机械连接的未增塑聚酰胺(PA-U)管系统. 第1部分: 总则; 修改件1

Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General; Amendment 1

ISO 16486-6:2012 气体燃料供给用塑料管道系统.带有热熔接头和机械接头的不加增塑剂的聚酰胺(PA-U)管道系统.第6部分:设计,操作和安装实施规程

This part of ISO 16486 specifies a code of practice dealing with unplasticized polyamide (PA-U) piping systems, intended to be buried outside buildings and used for the supply of gaseous fuels. It addresses the common basic principles for gas supply systems. More detailed national standards or codes of practice might exist in the ISO member countries. This part of to the above-mentioned basic principles. It is applicable to mains and service lines, the components of which are prepared for jointing by scraping and/or machining, and gives instructions for the design, storage, handling, transportation, laying conditions and fusion quality control of PA-U pipes and fittings up to and including 250 mm outside diameter, as well as subsequent joint testing, backfilling, pipe system testing, commissioning and decommissioning. The jointing methods covered by this part of ISO 16486 are butt fusion jointing and electrofusion jointing. No special precautions are necessary for areas exposed to the influence of mining and earthquakes other than those precautions mentioned in this part of ISO 16486. It is the responsibility of users of this part of ISO 16486 to take existing and new national regulations into account.

Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 6: Code of practice for design, handling and installation

ISO 16486-5:2012 气体燃料供给用塑料管道系统.带有热熔接头和机械接头的不加增塑剂的聚酰胺(PA-U)管道系统.第5部分:系统配件

This part of ISO 16486 specifies the requirements of fitness for purpose of the unplasticized polyamide (PA-U) piping system, intended to be buried and used for the supply of gaseous fuels. It also specifies the definitions of electrofusion and butt fusion joints. This part of ISO 16486 specifies the method of preparation of test piece joints and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. It also specifies the test parameters for the test methods to which it refers. and/or mechanical jointing. In conjunction with the other parts of ISO 16486, it is applicable to PA-U fittings, their joints and to joints with components of PA-U.

Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 5: Fitness for purpose of the system

ISO 22621-6:2010 最大操作电压小于并且包括2 MPa(20 bar)的燃料气体供应用塑料管道系统.聚酰胺(PA).第6部分:设计、操作和安装实施规程

This part of ISO 22621 specifies a code of practice dealing with polyamide (PA) piping systems, intended to be buried outside buildings and used for the supply of gaseous fuels. It is applicable to mains and service lines, the components of which are prepared for jointing by scraping and/or machining, and gives instructions for the design, storage, handling, transportation, laying conditions and fusion quality control of PA pipes and fittings up to and including 250 mm outside diameter, as well as subsequent joint testing, backfilling, pipe system testing, commissioning and decommissioning. The jointing methods covered by this part of ISO 22621 are butt fusion jointing and electrofusion jointing. No special precautions are necessary for areas exposed to the influence of mining and earthquakes other than those precautions mentioned in this part of ISO 22621. It is the responsibility of users of this part of ISO 22621 to take existing and new national regulations into account.

Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) - Polyamide (PA) - Part 6: Code of practice for design, handling and installation

ISO 22621-5:2010 最大操作电压小于并且包括2 MPa(20 bar)的燃料气体供应用塑料管道系统.聚酰胺(PA).第5部分:系统适用性

This part of ISO 22621 specifies the requirements of fitness for purpose of the polyamide (PA) piping system, intended to be buried and used for the supply of gaseous fuels at maximum operating pressures (MOP) up to and including 2 MPa (20 bar1)). It specifies the definitions of electrofusion and butt fusion joints. It also specifies the method of preparation of test piece joints and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. In addition, it specifies the test parameters for the test methods to which it refers. In conjunction with the other parts of ISO 22621, it is applicable to PA fittings, their joints and joints with components of PA.

Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) - Polyamide (PA) - Part 5: Fitness for purpose of the system

SANS 14692-3:2009 石油及天然气工业.玻璃纤维增强塑料(GRP)管道.第3部分:系统设计

Gives guidelines for the design of GRP piping systems. The requirements and recommendations apply to layout dimensions, hydraulic design, structural design, detailing, fire endurance, spread of fire and emissions and control of electrostatic discharge.

Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping Part 3: System design

SANS 14692-4:2009 石油及天然气工业.玻璃纤维增强塑料(GRP)管道.第4部分:制造、安装及操作

Gives requirements and recommendations for the fabrication, installation and operation of GRP piping systems for use in oil and natural gas industry processing and utility service applications. The recommendations apply to delivery, inspection, handling,

Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping Part 4: Fabrication, installation and operation

SANS 14692-2:2009 石油及天然气工业.玻璃纤维增强塑料(GRP)管道.第2部分:质量保证及制造

Gives requirements for the qualification and manufacture of GRP piping and fittings in order to enable the purchase of GRP components with known and consistent properties from any source. It is applicable to qualification procedures, preferred dimensions

Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping Part 2: Qualification and manufacture