23.040.01;91.140.40 标准查询与下载

BS PD CEN/TR 16787:2014 工业气体装置. 指南

Industrial Gas Installation. Guideline

DIN CEN/TS 1555-7:2013 气体燃料输送用塑料管道系统.聚乙烯(PE).第7部分:合格评定导则.德文版本CEN/TS 1555-7-2013

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for assessment of conformity; German version CEN/TS 1555-7:2013

PD CEN/TS 1555-7:2013 供应气体燃料的塑料管道系统 聚乙烯（PE） 第7部分：合格评定指南

This Technical Specification gives guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 1555 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures. It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001. NOTE 1 If certification is involved, the certification and inspection body is preferably compliant with EN 45011, EN 45012 or EN ISO/IEC 17020, as applicable. In conjunction with Parts 1 to 5 of EN 1555 (see Foreword), this Technical Specification is applicable to polyethylene (PE) plastics piping systems for the supply of gaseous fuels. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar1); b) an operating temperature of 20 °C as reference temperature. NOTE 2 For other operating temperatures, derating coefficients can be used; see EN 1555-5. For mechanical fittings conforming to ISO 10838-1, ISO 10838-2 or ISO 10838-3, as applicable, guidance for assessment of conformity is not given in this part of EN 1555. When requested, a quality plan based on the tests mentioned in ISO 10838-1, ISO 10838-2 or ISO 10838-3, as applicable, should be set up in agreement between user and manufacturer. EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours and additives. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity

DIN EN 1555-5:2010 气体燃料供应用塑料管道系统.聚乙烯(PE).第5部分:系统的适用性.德文版本EN 1555-5-2010

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system; German version EN 1555-5:2010

BS EN 1555-5:2010 气体燃料供应用塑料管系统.聚乙烯(PE).系统适用性

This part of EN 1555 specifies requirements of fitness for purpose of the polyethylene (PE) piping system in the field of the supply of gaseous fuels. It specifies the definitions of electrofusion, butt fusion and mechanical joints. It specifies the method of preparation of test piece joints, and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. It specifies the test parameters for the test methods referred to in this standard. In conjunction with Parts 1 to 4 of EN 1555, it is applicable to PE pipes, fittings, valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar 1); b) an operating temperature of 20 °C as reference temperature. NOTE 1 For other operating temperatures, derating coefficients should be used, see Annex A. EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE). Fitness for purpose of the system

NF T54-065-5:2010 燃气输送用塑料管道系统.聚乙烯(PE).第5部分:系统用途的适合性.

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5 : fitness for purpose of the system.

EN 1555-5:2010 燃气输送用塑料管系统 聚乙烯(PE) 第5部分:系统适用性

This part of EN 1555 specifies requirements of fitness for purpose of the polyethylene (PE) piping system in the field of the supply of gaseous fuels. It specifies the definitions of electrofusion, butt fusion and mechanical joints. It specifies the method of preparation of test piece joints, and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. It specifies the test parameters for the test methods referred to inThis standard. In conjunction with Parts 1 to 4 of EN 1555, it is applicable to PE pipes, fittings, valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar 1); b) an operating temperature of 20 ℃ as reference temperature. NOTE 1 For other operating temperatures, derating coefficients should be used, see Annex A. EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system

EN 15001-1:2009 天然气基础设施.工业设施大于0-5巴,工业和非工业设施大于5巴工作压力的天然气装置管道.第1部分:设计的详细功能要求

This European Standard specifies detailed functional requirements for the design; selection of materials; construction; inspection and testing of industrial gas installation pipework and assemblies with an operating pressure greater than 0;5 bar; and non-industrial gas installation pipework (residential and commercial) with an operating pressure greater than 5 bar in buildings; starting from the outlet of the network operator's point of delivery up to the inlet connection to the gas appliance; normally the inlet isolation valve.This standard also covers the inlet connection to the gas appliance comprising of the pipework that does not fall within the scope of the appliance standard.

Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, mater

BS EN 15001-2:2008 天然气基础设施.工业和非工业装置用工作压力≥5bar和工业装置用工作压力≥0.5bar供气装置管道工程.试运转、操作和维护用详细功能要求

This European Standard specifies detailed functional requirements for the commissioning, operation and maintenance of • industrial gas installations and assemblies with an operating pressure greater than 0,5 bar and of • non-industrial gas installations (residential and commercial) with an operating pressure greater than 5 bar, starting from the outlet of the network operator’s point of delivery up to the inlet connection to the gas appliance; normally the inlet isolation valve. This European Standard also covers the inlet connection to the gas appliance comprising of the pipework that does not fall within the scope of the appliance standard. This standard applies to gas installations operating at ambient temperatures between –20 °C and 40 °C and operating pressures up to and including 60 bar. For operating conditions outside these limitations, reference should additionally be made to EN 13480 for metallic pipework. For industrial gas installations up to and including 0,5 bar and for non-industrial (residential and commercial) gas installations up to and including 5 bar EN 1775 applies. For gas installations that do not fall within the scope of EN 1775 or other European Standards, this European Standard applies. In this European Standard, the term “gas“ refers to combustible gases, which are gaseous at 15 °C and 1 013 mbar absolute atmospheric pressure. These gases are commonly referred to as manufactured gas, natural gas or Liquefied Petroleum Gas (LPG). They are also referred to as first, second or third family gases (see table 1 of EN 437:2003). LPG storage vessels (including all ancillaries fitted directly to storage vessels) are excluded. Also excluded are LPG installations and sections of LPG installations operating at vapour pressure (e.g. between the storage vessel and its pressure regulator). In this European Standard, all pressures are gauge pressures unless otherwise stated. For gas installations within the scope of this standard, national legislation and regulations have to be taken into account. Functional requirements for design, selection of materials, construction, inspection and testing of industrial gas installations and assemblies with an operating pressure greater than 0,5 bar and of gas installations greater than 5 bar in buildings and areas intended for residential, commercial, public and mixed uses are described in prEN 15001-1.

Gas infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 2: Detailed functional requirements for commission

EN 15001-2:2008 天然气基础设施.工业和非工业装置用工作压力≥5bar和工业装置用工作压力≥0.5bar供气装置管道工程.第2部分:试运转,操作和维修用详细功能要求

This European Standard specifies detailed functional requirements for the commissioning, operation and maintenance of industrial gas installations and assemblies with an operating pressure greater than 0,5 bar and of; non-industrial gas installations (residential and commercial) with an operating pressure greater than 5 bar, starting from the outlet of the network operator's point of delivery up to the inlet connection to the gas appliance; normally the inlet isolation valve.This European Standard also covers the inlet connection to the gas appliance comprising of the pipework that does not fall within the scope of the appliance standard.This standard applies to gas installations operating at ambient temperatures between-20 ℃ and 40 ℃ and operating pressures up to and including 60 bar. For operating conditions outside these limitations, reference should additionally be made to EN 13480 for metallic pipework. For industrial gas installations up to and including 0,5 bar and for non-industrial (residential and commercial) gas installations up to and including 5 bar EN 1775 applies. For gas installations that do not fall within the scope of EN 1775 or other European Standards,This European Standard applies. InThis European Standard, the term "gas" refers to combustible gases, which are gaseous at 15 ℃ and 1013 mbar absolute atmospheric pressure. These gases are commonly referred to as manufactured gas, natural gas or Liquefied Petroleum Gas (LPG). They are also referred to as first, second or third family gases (see table 1 of EN 437:2003). LPG storage vessels (including all ancillaries fitted directly to storage vessels) are excluded. Also excluded are LPG installations and sections of LPG installations operating at vapour pressure (e. g. between the storage vessel and its pressure regulator). InThis European Standard, all pressures are gauge pressures unless otherwise stated. For gas installations within the scope of this standard, national legislation and regulations have to be taken into account. Functional requirements for design, selection of materials, construction, inspection and testing of industrial gas installations and assemblies with an operating pressure greater than 0,5 bar and of gas installations greater than 5 bar in buildings and areas intended for residential, commercial, public and mixed uses are described in prEN 15001-1.

Gas infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 2: Detailed functional requirements for commissioning

BS DD CEN/TS 1555-7:2003 飞行器燃料舱中用作爆炸抑制剂和挡板材料的纤维聚酰胺材料.试验方法

This Part of EN 1555 gives guidance for assessment of conformity to be included in the manufacturer's quality plan as part of the quality system. This Part of EN 1555 includes: a) requirements for materials, components and joints given in the applicable Parts of EN 1555; b) requirements for the manufacturer's quality system; NOTE 1 It is recommended that the quality system conforms to EN ISO 9001 [2]. c) definitions and procedures to be applied if third party certification is involved. NOTE 2 If third party certification is involved, it is recommended that the certification body is accredited to EN 45011 [3] or EN 45012 [4], as applicable. In conjunction with the other Parts of EN 1555 it is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar 1); b) an operating temperature of 20 °C as reference temperature. NOTE 3 For other operating temperatures, derating coefficients can be used, see EN 1555-5. For mechanical fittings conforming to ISO 10838-1 [5], ISO 10838-2 [6] or ISO 10838-3 [7], as applicable, guidance for assessment of conformity is not given in this part of EN 1555. When requested, a quality plan based on the tests mentioned in ISO 10838-1 [5], ISO 10838-2 [6] or ISO 10838-3 [7], as applicable, should be set up in agreement between user and manufacturer. EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours and additives. NOTE 4 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7:Guidance for the assessment of conformity

BS EN 1555-5:2004 供应气体燃料用塑料管道系统.聚乙烯(PE).系统的适用性

This part of EN 1555 specifies requirements of fitness for purpose of the polyethylene (PE) piping system in the field of the supply of gaseous fuels. It specifies the definitions of electrofusion, butt fusion and mechanical joints. It also specifies the method of preparation of test piece joints, relating to installation recommendations given in EN 12007-2:2000 and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with the other parts of EN 1555 (see Foreword) it is applicable to PE pipes, fittings, valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar; b) an operating temperature of 20 ℃ as reference temperature. NOTE 1 For other operating temperatures, derating coefficients should be used, see annex A. EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours and additives. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. note:1) 1 bar = 0,1 MPa

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Fitness for the purpose of the system

BS EN 1555-5:2002 法兰及其连接件.PN标示法兰用垫圈的尺寸.有槽法兰用聚合O形密封圈

This part of EN 1555 specifies requirements of fitness for purpose of the polyethylene (PE) piping system in the field of the supply of gaseous fuels. It specifies the definitions of electrofusion, butt fusion and mechanical joints. It also specifies the method of preparation of test piece joints, relating to installation recommendations given in EN 12007-2:2000 and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with the other parts of EN 1555 (see Foreword) it is applicable to PE pipes, fittings, valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar; b) an operating temperature of 20 ℃ as reference temperature. NOTE 1 For other operating temperatures, derating coefficients should be used, see annex A. EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours and additives. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. note:1) 1 bar = 0,1 MPa

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5:Fitness for purpose of the system