23.040.01;91.140.60 标准查询与下载

GB/T 28799.3-2012 冷热水用耐热聚乙烯（PE-RT）管道系统.第3部分：管件

GB/T 28799的本部分规定了耐热聚乙烯（ PE-RT ）管件（以下简称管件）的材料、产品分类、技术要求、试验方法、检验规则和标志、包装、运输、贮存。 本部分适用于PE-RT I型和PE-RT II型管材。 本部分与GB/T 28799.1、GB/T 28799.2配合使用,适用于建筑冷热水管道系统,包括民用与工业建筑冷热水、饮用水和采暖系统等。 本部分不适用于灭火系统。

Plastics piping systems for hot and cold water installations.Polyethylene of raised temperature resistance(PE-RT).Part3:Fittings

GB/T 28799.1-2012 冷热水用耐热聚乙烯(PE-RT)管道系统.第1部分：总则

GB/T 28799的本部分规定了冷热水用耐热聚乙烯(PE-RT)管道系统的术语和定义、符号和缩略语、使用条件级别、材料和卫生要求。 本部分适用于用PE-RT I型和PE-RT II型材料生产的管道系统。 本部分与GB/T 28799.2、GB/T 28799.3配合使用,适用于建筑冷热水管道系统,包括民用与工业建筑冷热水、饮用水和采暖系统等。 本部分不适用于灭火系统。

Plastics piping systems for hot and cold water installations.Polyethylene of raised temperature resistance(PE-RT).Part 1:General

BS EN ISO 13056:2018 塑料管路系统. 热冷水压力系统真空密封性试验方法

Plastics piping systems. Pressure systems for hot and cold water. Test method for leaktightness under vacuum

BS EN ISO 15876-5:2017 冷热水装置用塑料管道系统.聚丁烯.系统的适用性

Plastics piping systems for hot and cold water installations. Polybutene (PB). Fitness for purpose of the system

BS EN ISO 15876-1:2017 冷热水装置用塑料管道系统.聚丁烯.总则

Plastics piping systems for hot and cold water installations. Polybutene (PB). General

EN ISO 15876-1:2017 冷热水用塑料管道系统(PB)Polybutene -第1部分:一般(ISO 15876-1:2017)

Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General

ISO 15876-1:2017 热水和冷水装置用塑料管系统. 聚丁烯(PB). 第1部分: 总则

Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 1: General

GOST R 56927-2016 供水用定向未增塑聚氯乙稀管. 规格

Pipes made of oriented unplasticized polyvinylchloride for water supply. Specifications

GOST R 56730-2015 区域供暖用隔热塑料软管. 通用规格

Plastic flexible pipes with thermal insulation for district heating. General specifications

DIN CEN/TS 12201-7:2014 供水, 压力条件下排水和污水用塑料管道系统. 聚乙烯 (PE). 第7部分:一致性评估指南; 德文版本CEN/TS 12201-7-2014

Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity; German version CEN/TS 12201-7:2014

BS PD CEN/TS 12201-7:2014 供水, 压力条件下排水和污水用塑料管道系统. 聚乙烯 (PE). 一致性评估指南

Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE). Guidance for the assessment of conformity

PD CEN/TS 12201-7:2014 压力下供水、排水和污水处理用塑料管道系统 聚乙烯（PE） 第7部分：合格评定指南

This part of EN 12201 gives guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 12201 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures. It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001. NOTE 1 If certification is involved, the certification and inspection body is preferably compliant with EN ISO/IEC 17065 , EN ISO/IEC 17021 or EN ISO/IEC 17020, as applicable. In conjunction with Parts 1 to 5 of EN 12201 (see Foreword) this document is applicable to polyethylene (PE) plastics piping systems for water supply, and for drainage and sewerage under pressure. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) allowable operating pressure, PFA, up to 25 bar1); b) an operating temperature of 20 °C as a reference temperature; c) buried in the ground; d) sea outfalls; e) laid in water; f) above ground, including pipes suspended below bridges. NOTE 2 For applications operating at constant temperature greater than 20 °C and up to 40 °C, see EN 12201-1:2011, Annex A. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.

Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity

ASTM F2769-14 升温的 (PE-RT) 热水和冷水管道及分配系统用聚乙烯的标准规格

1.1 This specification establishes requirements for polyethylene of raised temperature (PE-RT) plastic hot- and cold-water tubing and distribution systems components made in one standard dimension ratio and intended for 100 psig (6.9 bar) water service up to and including a maximum working temperature of 180°F (82°C). Components are comprised of tubing, fittings, valves and manifolds. Tubing may incorporate an optional polymeric inner, middle or outer layer. Testing of Specification F1807 and F2159 fittings and PE-RT tubing to the requirements of this standard indicate that these fittings are appropriate for use with PE-RT piping systems. Requirements and test methods are included for materials, workmanship, dimensions and tolerances, burst pressure, sustained pressure, oxidative resistance, temperature cycling tests, bend strength and environmental stress cracking. Also included are tests related to system malfunctions. The components covered by this specification are intended for use in residential and commercial, hot and cold, potable water distribution systems. 1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. Note 1: Suggested hydrostatic design stresses and hydrostatic pressure ratings for tubing and fittings are listed in Appendix X1. UV labeling guidelines are provided in Appendix X2. Design, assembly, and installation considerations are provided in Appendix X3. An optional performance qualification and an in-plant quality control program are recommended in Appendix X4. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems

DIN EN ISO 15874-1:2013 冷热水装置用塑料管道系统.聚丙烯(PP).第1部分:总论(ISO 15874-1-2013).德文和英文版本EN ISO 15874-1-2013

Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General (ISO 15874-1:2013); German and English version EN ISO 15874-1:2013

DIN EN ISO 15874-5:2013 冷热水装置用塑料管道系统.聚丙烯(PP).第5部分:系统的适用性(ISO 15874-5-2013).德文和英文版本EN ISO 15874-5-2013

Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO 15874-5:2013); German and English version EN ISO 15874-5:2013

PD CEN/TR 12108:2012 塑料管道系统—指导压力管道系统安装在建筑物的热水和冷水用于人类消费

This European Technical Report recommends practices to be followed in the application and installation of thermoplastics pipes and associated fittings. These fall within the scope of EN 806-1 and, EN ISO 15874, EN ISO 15875, EN ISO 15876, EN ISO 15877 and EN ISO 22391 to be used for hot and/or cold water distribution intended for human consumption inside buildings.This document can also be used for heating installations if applicable, except for under floor heating for which EN 12164 can apply. Guidance is also given on acceptable methods of jointing polybutylene (PB), crosslinked polyethylene (PE-X), polypropylene (PP), chlorinated poly(vinyl chloride) (PVC-C) and Polyethylene of raised temperature resistance (PE-RT) pipes and associated fittings, together with recommendations for their storage, handling and transportation.

Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption

ISO 13056:2011 塑料管路系统.热冷水压力系统真空密封性试验方法

Plastics piping systems - Pressure systems for hot and cold water - Test method for leaktightness under vacuum

GOST R 54468-2011 直接受热,冷热水网络用热绝缘软管.一般规范

Flexible pipes with thermal insulation for district heating, hot and cold water networks. General specifications

DIN EN ISO 15874-1:2010 热水和冷水装置用塑料管系统. 聚丙烯(PP). 第1部分: 总则(ISO/DIS 15874-1-2010); 德文版本prEN ISO 15874-1-2010

Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General (ISO/DIS 15874-1:2010); German version prEN ISO 15874-1:2010

ANSI/ASTM F2769:2010 耐热聚乙烯(Pe-Rt)塑料热水和冷水管道和配电系统用规范

Specification For Polyethylene Of Raised Temperature (Pe-Rt) Plastic Hot And Cold-Water Tubing And Distribution Systems