23.040.01;91.140.80 标准查询与下载

BS PD CEN/TS 1453-2:2017 建筑物内污物和废水排放(低温和高温)用带结构壁管的塑料管道系统.未增塑的聚氯乙烯(PVC-U).符合性评定指南

Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings. Unplasticized poly(vinyl chloride) (PVC-U). Guidance for the assessment of conformity

ASTM A888-15 下水管, 雨水管, 污水管和排气管道用无衬套铸铁管和配件

1.1 This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage. 1.2 The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification. 1.3 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the applicable requirements given in this specification.2 1.3.1 Lengths:   Figures EDP/ASA Identification Numbers for Hubless Pipe Fig. 1 10 ft (3.0 m) in sizes and 5 ft. (1.5 m) 11/2 , 2, 3, 4, 5, 6, 8, 10, 12, and 15 in. Fig. 1, Fig. 2 Method of Specifying Fittings Fig. 3 1.3.2 Fittings:  Quarter Bend Fig. 5 Quarter Bend, Reducing

Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

DIN EN 1329-1:2014 建筑物污物和污水排放(低温和高温)用塑料管道系统.未增塑聚氯乙烯(PVC-U).第1部分:管道、配件和系统规范

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system; German version EN 1329-1:2014

EN 1329-1:2014 建筑物结构内污物和废水排放(低和高温)用塑料管道系统.硬塑聚氯乙烯(PVC-U).第1部分:管材,管件和系统规

This part of EN 1329 specifies the requirements for solid wall unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and the system intended for:- soil and waste discharge applications (low and high temperature) inside buildings (application area code "B"); - soil and waste discharge applications (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD"). NOTE 1 The intended use is reflected in the marking of products by "B" or "BD". NOTE 2 For use buried in ground within the building structure are intended only those components (marked with "BD") with nominal outside diameters equal to or greater than 75 mm. This part of EN 1329 is also applicable to PVC-U pipes, fittings and the system intended for the following purposes; - ventilating part of the pipework in association with discharge applications; - rainwater pipework within the building structure. It also specifies the test parameters for the test method referred to in this European Standard. This European Standard covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. For external above ground application additional requirements depending on the climate should be agreed between the manufacturer and the user. NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 24. NOTE 5 Joints and adhesives are considered to be part of the system as covered in the scope.

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system

DIN CEN/TS 1329-2:2012 建筑物结构内污物和废水排放 (低温和高温) 用塑料管道系统. 未增塑聚氯乙烯 (PVC. U). 第2部分:一致性评估指南; 德文版本CEN/TS 1329-2-2012

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity; German version CEN/TS 1329-2:2012

DIN CEN/TS 1455-2:2012 建筑结构内土壤和废弃物排出(低温与高温)用塑料管系统. 丙烯腈-丁二烯-苯乙烯共聚物(ABS). 第2部分: 一致性评估指南; 德文版本CEN/TS 1455-2-2012

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Guidance for the assessment of conformity; German version CEN/TS 1455-2:2012

DIN CEN/TS 1566-2:2012 建筑物结构内污物和废水排放 (低温和高温) 用塑料管道系统. 氯化聚氯乙烯 (PVC-C). 第2部分:一致性评估指南; 德文版本CEN/TS 1566-2-2012

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Guidance for the assessment of conformity; German version CEN/TS 1566-2:2012

DIN CEN/TS 1565-2:2012 建筑结构内土壤和废弃物排出(低温与高温)用塑料管系统. 苯乙烯-共聚物共混物. 第2部分: 一致性评估指南; 德文版本CEN/TS 1565-2-2012

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene-copolymer blends (SAN+PVC) - Part 2: Guidance for the assessment of conformity; German version CEN/TS 1565-2:2012

PD CEN/TS 1566-2:2012 建筑建构中排土壤和废弃物(高低温)的塑料管道系统 聚乙烯(PVC-C) 一致性评估指南

This Technical Specification gives guidance for the assessment of conformity of materials (compounds/formulations), products and assemblies in accordance with EN 1566-1 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of third-party certification procedures. NOTE 1 It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001. NOTE 2 If third-party certification is involved, it is recommended that the certification body is accredited to EN 45011, EN 45012 or EN ISO/IEC 17021, as applicable. NOTE 3 In order to help the reader, a basic test matrix is given in Annex A. In conjunction with EN 1566-1,This document is applicable to solid-wall piping systems made of chlorinated poly(vinyl chloride) (PVC-C) intended to be used for the following purposes: for soil and waste discharge systems (low and high temperature) inside buildings (application area code "B"); for soil and waste discharge systems (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD"). NOTE 4This is reflected in the marking of products by "B" or "BD".

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Guidance for assessment of conformity

BS EN 15012:2007 塑料管道系统.建筑结构内部的粪便和废弃物排放系统.管道、配件及其连接件的性能特性

This document specifies performance requirements for non-pressure plastics pipes, fittings and their joints intended for soil and waste applications:  inside the building (application area code "B"),  buried in ground within the building structure (application area code "BD") and with a diameter greater than or equal to 75 mm, and gives associated test methods for verification and evaluation of conformity with this document.

Plastics piping systems - Soil and waste discharge systems within the building structure - Performance characteristics for pipes, fittings and their joints

DIN EN 15012:2008 塑料管系统.建筑结构内污物和废弃物排放系统.管道、配件及其连接件用性能特点

This document specifies performance requirements for non-pressure plastics pipes, fittings and their joints intended for soil and waste applications: -- inside the building (application area code "B"), -- buried in ground within the building structure (application area code "BD") and with a diameter greater than or equal to 75 mm, and gives associated test methods for verification and evaluation of conformity with this document.

Plastics piping systems - Soil and waste discharge systems within the building structure - Performance characteristics for pipes, fittings and their joints; English version of DIN EN 15012:2008-02

NF T54-977:2008 塑料管道系统.建筑结构内部的污泥和废水排放系统.管道、配件及其连接件的性能特性

Plastics piping systems - Soil and waste discharge systems within the building structure - Performance characteristics for pipes, fittings and their joints.

CEN EN 15012-2007 塑料管道系统 建筑结构内的土壤和废物排放系统 管道、配件及其接头的性能特征

This document specifies performance requirements for non-pressure plastics pipes, fittings and their joints intended for soil and waste applications: ? inside the building (application area code "B"), ? buried in ground within the building structure (application area code "BD") and with a diameter greater than or equal to 75 mm, and gives associated test methods for verification and evaluation of conformity with this document.

Plastics piping systems — Soil and waste discharge systems within the building structure — Performance characteristics for pipes, fittings and their joints

BS DD CEN/TS 12666-2:2006 非承压地下排放和污水用塑料管道系统.聚乙烯(PE).符合性评定指南

Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Guidance for the assessment of conformity

BS DD ENV 1451-2:2001 建筑物内污物和污水排放(高、低温)用塑料管道系统.聚丙烯(PP).符合性评定指南

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Guidance for the assessment of conformity

DD ENV 1451-2-2001 建筑物内粪水和废物排放的塑料管道系统(低温和高温).聚丙烯.符合性评定指南

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polypropylene (PP). Guidance for the assessment of conformity

DD ENV 1455-2-2001 建筑物内粪和废物排放的塑料管道系统(低温和高温).丙烯腈-丁二烯-苯乙烯共聚物.符合性评定指南

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Acrylonitrile-butadiene- styrene (ABS). Guidance for the assessment of conformity

DD ENV 1329-2-2001 建筑物内粪水和废物排放的塑料管道系统(低温和高温).未增塑聚氯乙烯（PVC－U）.符合性评定指南

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U). Guidance for the assessment of conformity

BS DD ENV 1519-2:2001 建筑物内污物污水排放(高、低温)用塑料管道系统.聚乙烯(PE).符合性评定指南

This Part of EN 1519 gives guidance for the assessment of conformity to be included in the manufacturer's quality plan as part of the quality system. This prestandard includes: a) requirements for materials, components, joints and assemblies given in EN 1519-1 :1999; b) requirements for the manufacturer's quality system; NOTE 1 It is recommended that the quality system conforms to EN IS0 9001, as applicable. c) definitions and procedures to be applied if third party certification is involved. NOTE 2 If third party certification is involved, it is recommended that the certification body is accredited to EN 4501 1 or EN 4501 2, as applicable. This Part of EN 1519 is applicable to solid-wall piping systems made of polyethylene (PE) in the field of soil and waste discharge (low and high temperature) - inside buildings (application area code "B") and - inside buildings and buried in ground within the building structure (application area code "BD").

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Guidance for the assessment of conformity

DD ENV 1519-2-2001 建筑物内土壤和废物排放的塑料管道系统(低温和高温).聚乙烯.符合性评定指南

This Part of EN 1519 gives guidance for the assessment of conformity to be included in the manufacturer's quality plan as part of the quality system. This prestandard includes: a) requirements for materials, components, joints and assemblies given in EN 1519-1 :1999; b) requirements for the manufacturer's quality system; NOTE 1 It is recommended that the quality system conforms to EN IS0 9001, as applicable. c) definitions and procedures to be applied if third party certification is involved. NOTE 2 If third party certification is involved, it is recommended that the certification body is accredited to EN 4501 1 or EN 4501 2, as applicable. This Part of EN 1519 is applicable to solid-wall piping systems made of polyethylene (PE) in the field of soil and waste discharge (low and high temperature) - inside buildings (application area code "B") and - inside buildings and buried in ground within the building structure (application area code "BD").

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE). Guidance for the assessment of conformity