23.040.20;91.140.60;93.025 标准查询与下载

ISO 10639:2017 压力和无压力给水塑料管道系统.基于不饱和聚酯树脂的玻璃增强热固性塑料(GRP)系统

This document specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of water supply with or without pressure, including, but not limited to, raw water, irrigation, cooling water, potable water, salt water, sea water, penstocks in power plants, processing plants and other water-based applications. This document is applicable to GRP UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in direct buried installations. NOTE 1 For the purpose of this document, the term polyester resin (UP) also includes vinyl-ester resins (VE). NOTE 3 This document can also apply for other installations, such as slip-lining rehabilitation of existing pipes. NOTE 2 Piping systems conforming to this document can also be used for non-buried applications, provided the influence of the environment and the supports are considered in the design of the pipes, fittings and joints. NOTE 4 This document is also referenced in ISO 25780, which specifies requirements for GRP-pipes used for jacking installation. The requirements for the hydrostatic pressure design of pipes referring to this document meet the requirements of ISO/TS 20656-1 and the general principle for the reliability of structures detailed in design practices and address the probability of failure, as well as possible consequences of failures. The design practices are based on a partial safety factor concept, as well as on risk management engineering. This document is applicable to pipes, fittings and their joints of nominal sizes from DN 50 to DN 4000 which are intended to be used for the conveyance of water at temperatures up to 50 °C, with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together. Clause 4 specifies the general aspects of GRP UP piping systems intended to be used in the field of water supply with or without pressure. Clause 5 specifies the characteristics of pipes made from GRP UP with or without aggregates and/or fillers. The pipes may have a thermoplastics or thermosetting resin liner. Clause 5 also specifies the test parameters for the test methods referred to in this document. Clause 6 specifies the characteristics of fittings made from GRP UP, with or without a thermoplastics or thermosetting resin liner, intended to be used for conveyance of water. Clause 6 specifies the dimensional and performance requirements for bends, branches, reducers, saddles and flanged adaptors. Clause 6 covers requirements to prove the structural design of fittings. It is applicable to fittings made using any of the following techniques: — fabrication from straight pipes; — moulding by 1) filament winding, 2) tape winding, 3) contact moulding, and  1  4) hot or cold compression moulding. Clause 7 is applicable to the joints to be used in GRP UP piping systems to be used for the conveyance of water, both buried and non-buried. It covers requirements to prove the design of the joint. Clause 7 specifies type test performance requirements for the following joints as a function of the declared nominal pressure rating of the pipeline or system: a) socket-and-spigot (including double-socket) joints or mechanical joints; c) cemented or wrapped joints; b) locked socket-and-spigot joints; d) bolted flange joints.

Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin

KS M ISO 22391-2:2015 冷热水装置用塑料管道系统.耐升温的聚乙烯(PE-RT).第2部分:管道

Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance(PE-RT) — Part 2: Pipes

JIS K 6762 AMD 1:2014 给水用双层壁聚乙烯管(修改件1)

Double wall polyethylene pipes for water supply (Amendment 1)

JIS K 6761 AMD 1:2014 通用聚乙烯管(修改件1)

Polyethylene pipes for general purposes (Amendment 1)

ISO 4427-2:2007/Amd 1:2014 塑料管系统. 供水用聚乙烯(PE)管和配件. 第2部分: 管; 修改件1

Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Part 2: Pipes; Amendment 1

BS PD ISO/TR 4191:2014 供水用塑料管系统. 未增塑聚氯乙烯(PVC-U)和定向PVC-U (PVC-O). 安装指南

Plastics piping systems for water supply. Unplasticized poly(vinyl chloride)(PVC-U) and oriented PVC-U (PVC-O). Guidance for installation

ISO/TR 4191:2014 供水用塑料管道系统.未增塑聚氯乙烯(PVC-U)和定向PVC-U (PVC-O).安装导则

Plastics piping systems for water supply - Unplasticized poly(vinyl chloride)(PVC-U) and oriented PVC-U (PVC-O) - Guidance for installation

DS/CEN/TR 852:2011 供人类饮用水运输用塑料管道系统 迁移评估 实验室导出迁移值解释指南

This Technical Report is applicable to plastics pipes, joints and fittings to be used for the transport of water intended for human consumption and raw water used for the manufacture of water intended for human consumption.It gives guidance on:a) the number of successive migration periods to be carried out;b) how to interpret M values calculated from successive migration periods;c) a method for converting M values into values that reflect field use conditions;d) acceptance criteria for the duplicate M values obtained by testing in accordance with EN ISO 8795.

Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Guidance on the interpretation of laboratory derived migration values

DS/EN ISO 1452-5:2011 压力下供水和地下和地上排水和污水处理用塑料管道系统 未增塑聚（氯乙烯）（PVC-U） 第5部分：系统适用性

This part of ISO 1452 specifies the characteristics for the fitness for purpose of unplasticized poly(vinyl chloride) (PVC-U) piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure.It also specifies the test parameters for the test methods referred to in this part of ISO 1452.In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-4, it is applicable to joints andassemblies with components of PVC-U, other plastics and non-plastics materials intended to be used for the following:a) water mains and services buried in ground;b) conveyance of water above ground for both outside and inside buildi

Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 5: Fitness for purpose of the system

LST EN ISO 22391-2:2010 冷热水装置用塑料管道系统 耐高温聚乙烯（PE-RT） 第2部分：管道（ISO 22391-2:2009）

Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 2: Pipes (ISO 22391-2:2009)

BS EN ISO 22391-2:2009 冷热水装置用塑料管道系统.耐升温的聚乙烯(PE-RT).管道

This part of ISO 22391 specifies the characteristics of pipe made of - polyethylene of raised temperature resistance (PE-RT), Type I, and - polyethylene of raised temperature resistance (PE-RT), Type II, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1. This part of ISO 22391 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. In conjunction with the other parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT, as well as of other plastics and non-plastics materials, respectively, used for hot and cold water installations. It is applicable to pipes with or without a barrier layer or layers. It is not applicable to values of design temperature, maximum design temperature or malfunction temperature in excess of those specified in ISO 22391-1. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Pipes

ISO 22391-2:2009 冷热水装置用塑料管道系统.耐升温的聚乙烯(PE-RT).第2部分:管道

Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 2: Pipes

EN ISO 22391-2:2009 冷热水装置用塑料管道系统.耐升温的聚乙烯(PE-RT).第2部分:管道

This part of ISO 22391 specifies the characteristics of pipe made of

Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 2: Pipes (ISO 22391-2:2009)

SANS 22391-2:2008 冷热水装置用塑料管道系统.耐升温的聚乙烯(PE-RT).第2部分:管道

Specifies the characteristics of pipe made from polyethylene of raised temperature resistance (PE-RT), intended to be used for hot and cold water installations within buildings for the conveyance of water - whether or not the water is intended for human

Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) Part 2: Pipes

SANS 4427-2:2008 塑料管道系统.给水用聚乙烯(PE)管和管件.第2部分:管道

Specifies the pipes made from polyethylene (PE) intended for the conveyance of water for human consumption, including raw water prior to treatment and water for general purposes.

Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Part 2: Pipes

DS/EN ISO 8795:2001 供人类饮用水运输用塑料管道系统 迁移评估 塑料管道和配件及其接头迁移值的测定

This standard specifies a method for the determination of the migration of constituents from the internal surface of plastics pipes, fittings and joints. Organoleptic and microbiological assessments are not included. This standard is applicable to all plastics pipes, fittings and joints to be used for the transport of water intended for human consumption and raw water used for the manufacturing of water intended for human consumption. It covers all constituents which are extractable by water from a finished pipe, fitting or joint. It provides for a change in procedure as necessary depending upon the size of the pipe, fitting or joint.

Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values for plastics pipes and fittings and their joints

DS/ENV 1452-7:2001 供水塑料管道系统 未增塑聚（氯乙烯）（PVC-U） 第7部分：合格评定指南

This European Prestandard gives guidance for the assessment of conformity intended to be included in the manufacturer's quality plan as part of the quality system. This prestandard includes: a) requirements for materials, components, joints and assemblies given in Parts 1 to 5 of EN 1452:1999; b) requirements for the manufacturer's quality system; c) definitions and procedures to be applied if third party certification is involved. In conjunction with Parts 1 to 5 of EN 1452:1999 it is applicable to PVC-U piping systems intended to be used for the following: a) water mains and services buried in ground; b) conveyance of water above ground for both outside a

Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 7: Guidance for the assessment of conformity