23.040.45;23.040.60 标准查询与下载

BS DD ISO/TS 19911:2010 塑料管线和配件.特征聚乙烯(PE)插口端头配件用技术文件格式

Plastics pipes and fittings - Format of a technical file for characterizing PE spigot end fittings

LST EN 803-2002 塑料管道系统 压力管道弹性密封环型接头用注塑成型热塑性塑料配件 无端推力时耐短期内压的试验方法

Plastics piping systems - Injection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping - Test method for resistance to a short-term internal pressure without end thrust

LST EN 804-2002 塑料管道系统 压力管道用溶剂粘合接头用注塑承插管件 耐短期内部静水压力的试验方法

Plastics piping systems - Injection-moulded socket fittings for solvent-cemented joints for pressure piping - Test method for resistance to a short-term internal hydrostatic pressure

ANSI/ASTM F1986:2001 冷热饮用水系统用2型多层管压合配件和压合接头的规范

This specification covers requirements for multilayer pipe type 2 and compression fittings for hot and cold drinking-water systems, with a maximum pressure rating of 1000 kPa (145 psi) at 82?C (180?F). Note 1Multilayer Pipe Type 2-Construction-based pressure rated pipe comprising more than one layer in which at least 60 % of the wall thickness is polymeric material. Multilayer pipe type 2 is produced using a butt-welded aluminum pipe as a core, with an extruded inside layer of crosslinked polyethylene (PEX). An adhesive layer is used to bond the inside layer to the wall of the aluminum pipe. An outer layer of polyethylene (PE) and an adhesive layer are extruded to the outer wall of the aluminum pipe. Multilayer pipe type 2 is produced in configurations 1 and 2, as referenced in Fig. 1. This specification includes compression fittings, which are referenced in Fig. 2. Specifications for thread or solder adapters for use with pipe and fittings meeting the requirements of this specification are given in Annex A1 and Annex A2. The following precautionary caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The values stated in either SI units or in inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-water Systems

ANSI/ASTM F1987:2001 循环加热系统用2型多层管、压合配件和压合接头的规范

This specification covers requirements for multilayer pipe type 2 and compression fittings for hydronic heating systems, with a maximum pressure/temperature range of 1000 kPa (145 psi), at 82?C (180?F). Note 1Multilayer Pipe Type 2-Construction-based pressure rated pipe comprising more than one layer in which at least 60 % of the wall thickness is polymeric material. Multilayer pipe type 2 is produced using a butt-welded aluminum pipe as a core, with an extruded inside layer of crosslinked polyethylene (PEX). An adhesive layer is used to bond the inside layer to the wall of the aluminum pipe. An outer layer of polyethylene (PE) and an adhesive layer are extruded to the outer wall of the aluminum pipe. Multilayer pipe type 2 is produced in Configurations 1 and 2, as shown in Fig 1. This specification includes compression fittings, which are referenced in Fig. 2. Specifications for threaded or solder adapters for use with pipe and fittings meeting the requirements of this specification are given in Annex A1 and Annex A2. The following safety hazards caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this specification. Note 2Multilayer pipe type 2, configurations 1 and 2, for hydronic heating systems are not compatible for drinking water use.

Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hydronic Heating Systems

SR EN 804-1996 塑料管道系统．溶剂的喷射铸模插件．压力管道用的水泥接头．抗短期内部静水力压力的测试方法

Plastics piping systems - Injection-moulded socket fittings for solvent-cemented joints for pressure piping - Test method for resistence to a short-term internal hydrostatic pressure

DIN EN 803:1994 塑料管道系统.压力管道用橡胶密封圈连接件的热塑喷铸管件.无端部拉力的抗瞬时内压的试验方法; 德文版本 EN 803:1994

The document specifies a test method for checking the resistance of injection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping to a short-term internal pressure without end thrust.

Plastics piping systems - Injection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping - Test method for resistance to a short-term internal pressure without end thrust; German version EN 803:1994

DIN EN 804:1994 塑料管道系统.压力管道用带胶粘套管连接件的热塑喷铸管件.抗流体静力瞬时内压能力的试验方法; 德文版本 EN 804:1994

The document specifies a test method for checking the resistance of injection-moulded socket fittings for solvent-cemented joints for pressure piping systems to a short-term internal hydrostatic pressure.

Plastics piping systems - Injection-moulded socket fittings for solvent-cemented joints for pressure piping - Test method for resistance to a short-term internal hydrostatic pressure; German version EN 804:1994

EN 803:1994 塑料管道系统.压力管道用橡胶密封圈连接件的热塑喷铸管件.无端部拉力的抗瞬时内压的试验方法

This standard specifies a method for testingThe resistance to internal hydrostatic pressure at 20 of any injection-mouldedThermoplastics fittings with elastic sealing ring type joints forThermoplastics pressure pipes having a nominal diameter, less than or equal to 315 mm, whereThe joint is not intended to withstand hydrostatic and thrust.

Plastics piping systems - Injection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping - Test method for resistance to a short-term internal pressure without end thrust

EN 804:1994 塑料管道系统.压力管道溶焊接头的喷射铸造插接部件 瞬时内部液压阻力的试验方法

The document specifies a test method for checkingThe resistance of injection-moulded socket fittings for solvent-cemented joints for pressure piping systems to a short-term internal hydrostatic pressure.

Plastics piping systems - Injection-moulded socket fittings for solvent-cemented joints for pressure piping - Test method for resistance to a short-term internal hydrostatic pressure

BS 4346-3:1982 未增塑聚氯乙烯压力管的接头及配件.第3部分:溶粘剂规范

Requirements for cements for jointing thermoplastics pressure and non-pressure pipes.

Joints and fittings for use with unplasticized PVC pressure pipes - Specification for solvent cement

BS 5114:1975 与聚乙烯管共用的连结件和压制配件性能要求规范

Resistance to hydrostatic pressure, external pressure and pull-out of assembled joints and effect on water and opacity.

Specification for performance requirements for joints and compression fittings for use with polyethylene pipes

BS 4346-2:1970 未增塑聚氯乙烯压力管用接头及配件规范.第2部分:主要为未增塑聚氯乙烯的机械接头和配件

Material, dimensions, appearance, marking, sampling, tests for stress relief, resistance to sulphuric acid, opacity, effect on water, pressure effects.

Joints and fittings for use with unplasticized PVC pressure pipes. Mechanical joints and fittings, principally of unplasticized PVC