23.100.10 泵和马达 标准查询与下载
共找到 290 条与 泵和马达 相关的标准，共 20 页
本文件确立了一个容积式液压泵的源流量脉动和源阻抗的测试程序。 本文件适用于稳态条件下,泵激频率在50 Hz~400 Hz 的范围内的所有类型和尺寸规格的容积式泵。 本文件以计算高阻抗压力波动作为示例。测试程序的方法和理论基础解释在附录A中给出。测试程序称为双压力/双系统方法。评级如下: a)超过10 个单独的泵激频率谐波的源流量脉动(标准诺顿模型中)幅值(m3/s)和相位(°);3 b)超过10 个单独的泵激频率谐波的源流量脉动(修正模型中)幅值(m /s)、相位(°)和时域波形;5 /m )和相位(c)超过10 个单独的泵激频率谐波的源阻抗幅值(N·s °); d)超过10 个单独的泵激频率谐波的高阻抗压力波动(MPa),压力波动谐波f1 ~f10 的均方根平均值。
Hydraulic fluid power—Determination method of pressure ripple levels generated in systems and components—Part 1:Hydraulic pumps(precise method)
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2022-10-12
- 实施
- 2022-10-12
本文件规定了液压泵的流体压力波动特征值的测试程序(最大误差为+1dB~-3dB)。 本文件适用于液压泵压力波动特征的测量与数据处理。
Hydraulic fluid power—Determination method of pressure ripple levels generated in systems and components—Part 2: Hydraulic pumps(simplified method)
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2022-10-12
- 实施
- 2022-10-12
Hydraulic fluid power—Test code for the determination of noise level of hydraulic motors
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2017-11-01
- 实施
- 2018-05-01 00:00:00.0
本标准规定了在稳态工况和规定的连续转速下容积式液压泵和马达空载排量的测定方法。被试元件作为泵进行试验时,在轴端输入机械能,油口输出液压能;而被试元件作为马达进行试验时,从油口输入液压能,轴端输出机械能。
Hydraulic fluid power.positive displacement pumps and motors.Determination of derived capacity
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2012-12-31
- 实施
- 2013-10-01
本标准规定了液壓傳動用容積式長、馬達和整体传动装置稳态性能和效率的测定方法,以及在稳态条件下对试验装置.试验程序的要求和试验结果的表达。 本标准适用于容积式液压泵、马达和整体传动装置。
Hydraulic fluid power.Positive displacement pumps, motors and integral transmissions.Methods of testing and presenting basic steady state performance
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2011-06-16
- 实施
- 2012-03-01
本标准规定了电控液压泵(以下简称泵)的稳态和动态性能特性的试验方法。注本标准仅涉及与电控装置相关的泵特性试验方法。 本标准所涉及的泵都具有与输入电信号成比例地改变输出流量或压力的功能。这些泵可以是负载敏感控制泵、伺服控制泵，也可以是电控变量泵。 测量准确度分为A、B、C三级，详细见附录A。
Hydraulic fluid powder.Electrically controlled hydraulic pumps.Test methods to determine performance characteristics
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2009-03-16
- 实施
- 2009-11-01
GB/T 20421的本部分规定了定量或变量容积式旋转液压马达的低速特性的测定方法。 本方法包括了在低速条件下的试验，在这种速度下，可能产生对马达稳定持续的转矩输出有重要影响的液压脉冲频率，并且会影响到马达所连接的系统。 测量的准确度划分为A、B、C三个等级，在附录A中给出说明。
Hydraulic fluid power.Determination of characteristics of motors.Part 1:At constant low speed and at constant pressure
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2006-08-22
- 实施
- 2007-01-01
GB/T 20421的本部分规定了定量或变量容积式液压马达在恒流量和恒转矩下低速特性的测定方法。 本方法包括了在低速条件下的试验，在这种速度下，可能产生对马达稳定持续的转矩输出有重要影响的液压脉冲频率，并且会影响到马达所连接的系统。 测量的准确度分别为A、B、C三个等级，在附录A中给出说明。
Hydraulic fluid power.Determination of characteristics of motors.Part 3:At constant flow and at constant torque
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2006-08-22
- 实施
- 2007-01-01
GB/T 20421的本部分描述了测定旋转液压马达起动性的两种方法。 这是两种相似的测量方法，恒转矩法（见第6章）和恒压力法（见第7章）。由于获得的结果是相同的，所以两种方法没有优劣之分。 在附录A中给出附加物理量及字母符号的说明。 测量的准确度划分为A、B、C三个等级，在附录B中给出说明。
Hydraulic fluid power.Determination of characteristics of motors.Part 2:Startability
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2006-08-22
- 实施
- 2007-01-01
本标准规定了在用喷油泵试验台的技术要求、校验方法和校验规则。 本标准适用于在用喷油泵试验台（以下简称试验台）的校验。
Calibrating rule of using fuel injection pump test-bench
- ICS
- 23.100.10
- CCS
- J94
- 发布
- 1998-05-08
- 实施
- 1998-12-01
本标准规定了计量泵的型式与基本参数、技术要求、试验方法和检验规则、标志、包装及贮存。 本标准适用于输送温度为-30～100℃、粘度为0.3～800mm/s、不含固体颗粒的腐蚀性或非腐蚀性液体的柱塞计量泵和隔膜计量泵（以下简称“泵”）。
Metering pump
- ICS
- 23.100.10
- CCS
- J71
- 发布
- 1996-12-23
- 实施
- 1997-07-01
本标准规定了液压泵和马达的安装法兰和轴伸的尺寸系列及标记。 本标准适用于采用菱形、方形、矩形安装法兰和轴伸的液压泵和马达。 本标准不适用于有特殊要求的液压泵和马达。
Hydraulic fluid power-Positive displacement pumps and motors-Dimensions and identification code for mounting flanges and shaff ends Part1:Two-and four-hole flanges and shaft ends
- ICS
- 23.100.10
- CCS
- K13
- 发布
- 1994-08-29
- 实施
- 1995-07-01
Hydraulic fluid power—Positive displacement pumps and motors—Dimensions and identification code for mounting flanges and shaft ends—Part 1:Two-and four-hole flanges and shaft ends
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 1994-08-29
- 实施
- 1995-07-01
本标准规定了液压泵和马达用多边形安装法兰（包括圆形安装法兰）与轴伸的尺寸系列和标记。 本标准适用于采用多边形发装法兰（包括圆形安装法兰）和轴伸的各类液压泵和马达。
Hydraulic pump and motor mounting flange and shaft extension ruler marking and marking, polygonal flange (including circular flange)
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 1993-01-11
- 实施
- 1993-10-01
本标准规定了以液压油为工作介质的容积式液压泵和液压马达在稳态工况下空载排量的测定方法。
Hydraulic fluid power--Positive displacement pumps and motors--Determination of derived capacity
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 1987-06-12
- 实施
- 1988-01-01
Hydraulic Pumps Part 1: Vane Pumps
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2023-12-29
- 实施
- 2024-07-01
Hydraulic Pumps Part 3: Axial Piston Pumps
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2023-12-29
- 实施
- 2024-07-01
The purpose of IEC 60545:2021 is to establish, in a general way, suitable procedures for commissioning and operation of hydraulic machines and associated equipment, and to indicate how such machines and equipment should be commissioned and operated. Commissioning and operation of the associated equipment are not described in detail in this document but is considered in the commissioning and operation procedure as a separate step. Machines of up to about 15 MW and reference diameters of about 3 m are generally covered by IEC 62006. It is understood that a guideline of this type will be binding only if the contracting parties have agreed upon it. The guidelines exclude matters of purely commercial interest, except those inextricably connected with the conduct of commissioning and operation. The guidelines are not concerned with waterways, gates, drainage pumps, cooling-water equipment, generators, motor-generators, electrical equipment (e.g. circuit breakers, transformers) etc., except where they cannot be separated from the hydraulic machinery and its equipment. Wherever the guidelines specify that documents, drawings or information are supplied by a supplier (or by suppliers), each individual supplier should furnish the appropriate information for its own supply only. This second edition cancels and replaces the first edition published in 1976 and the first edition of IEC 60805 published in 1985. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) the focus is on the commissioning and operation of the hydraulic machine. Interfaces to the electric machine are mentioned only for a better understanding of the context; b) the definitions of tests for commissioning and adjustable speed are updated to state of the art; c) the record sheets ‘measurements during erection’ are excluded (see IEC 63132 (all parts)); d) the maintenance is excluded (see IEC 62256).
Guidelines for commissioning and operation of hydraulic turbines, pump-turbines and storage pumps
- ICS
- 23.100.10
- CCS
- 发布
- 2023-09-10
- 实施
本文件规定了工程机械用斜盘式液压轴向柱塞泵（以下简称“柱塞泵”）的术语和定义、分类和基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以液压油液或性能相当的其他液体为工作介质，额定压力不大于45 MPa的用于工程机械的斜盘式轴向柱塞泵。
Swash plate hydraulic axial piston pump for engineering machinery
- ICS
- 23.100.10
- CCS
- C344
- 发布
- 2023-09-01
- 实施
- 2023-09-15
