25.080.20;25.080.40 标准查询与下载

KS B ISO 3686-2:2014 带垂直轴固定高度工作台的高准确度六角和单轴坐标钻床和镗床的试验条件.准确度的试验.第2部分:带移动工作台的移动式凿岩机

Test conditions for high accuracy turret and single spindle coordinate drilling and boring machines with table of fixed height with vertical spindle — Testing of the accuracy — Part 2: Portal type machines with moving table

KS B ISO 3686-1:2014 带垂直轴固定高度工作台的高准确度六角和单轴坐标钻床和镗床的试验条件.准确度的试验.第1部分:单柱式凿岩机

Test conditions for high accuracy turret and single spindle coordinate drilling and boring machines with table of fixed height with vertical spindle — Testing of the accuracy — Part 1: Single column type machines

ANSI B11.8-2001 机床.带或不带自动控制的手动铣床、钻床和镗床用安全要求

This American National Standard specifies safety requirements for the design, construction, operation and maintenance (including installation, dismantling and transport) of manually controlled milling, drilling, and boring machines. This standard also ap

Machine Tools - Safety Requirements for Manual Milling, Drilling and Boring Machines with or without Automatic Control

ANSI B11.23-2001 组合加工中心机床和自动数控铣床、钻床和镗床的安全要求

This standard specifies the safety requirements for the design, construction, operation and maintenance (including installation, dismantling and transport) of machining centers and automatic numerically controlled milling, drilling and boring machines.

Safety Requirements for Machining Centers and Automatic Numerically Controlled Milling, Drilling and Boring Machines

BS ISO 3686-1:2000 带垂直主轴固定高度工作台的高准确度六角和单轴坐标钻床和镗床的试验条件.准确度的试验.单柱式机床

This part of ISO 3686 specifies, with reference to ISO 230-1; both geometric tests and machining tests on vertical spindle, single column type coordinate drilling and boring machines. It also specifies the applicable tolerances corresponding to the above-mentioned tests. It should be noted that, besides drilling and boring operations, it may be possible to carry out light milling operations with these machines. However, this part of ISO 3686 does not deal with jig boring machines or machining centres. This part of ISO 3686 deals only with the verification of the accuracy of the machine. It does not apply to the testing of the machine operation (vibrations, abnormal noises, the stick-slip motion of components, etc.), nor the machine characteristics (such as speeds, feeds, etc.), which should generally be carried out before testing the accuracy. This part of ISO 3686 provides the terminology used for the principle components of the machine and indicates the designation of the axes in accordance with ISO 841.

Test conditions for high accuracy turret and single spindle coordinate drilling and boring machines with table of fixed height with vertical spindle - Testing of the accuracy - Single column type machines

BS ISO 3686-2:2000 带垂直主轴固定高度工作台的高准确度六角和单轴坐标钻床和镗床的试验条件.准确度的试验.带移动工作台的轻便式机床

This part of ISO 3686 specifies, with reference to ISO 230-1, both geometric tests and machining tests on vertical spindle, portal type coordinate drilling and boring machines. It also specifies the applicable tolerances corresponding to the above-mentioned tests. It should be noted that, besides drilling and boring operations, it may be possible to carry out light milling operations with these machines. However, this part of ISO 3686 does not deal with jig boring machines or machining centres. This part of ISO 3686 deals only with the verification of accuracy of the machine. It does not apply to the testing of the machine operation (vibrations, abnormal noises, stick-slip motion of components, etc.), nor the machine characteristics (such as speeds, feeds, etc.), which should generally be carried out before testing the accuracy. This part of ISO 3686 provides the terminology used for the principle components of the machine and indicates the designation of the axes in accordance with ISO 841.

Test conditions for high accuracy turret and single spindle coordinate drilling and boring machines with table of fixed height with vertical spindle - Testing of the accuracy - Portal type machines with moving table

ISO 3686-2:2000 高精度立式转塔和单轴工作台不升降坐标钻镗床检验条件 精度检验 第2部分:带活动工作台的龙门式机床

This part of ISO 3686 specifies, with reference to ISO 230-1, both geometric tests and machining tests on vertical spindle, portal type coordinate drilling and boring machines. It also specifies the applicable tolerances corresponding to the above-mentioned tests. It should be noted that, besides drilling and boring operations, it may be possible to carry out light milling operations with these machines. However, this part of ISO 3686 does not deal with jig boring machines or machining centres. This part of ISO 3686 deals only with the verification of accuracy of the machine. It does not apply to the testing of the machine operation (vibrations, abnormal noises, stick-slip motion of components, etc.), nor the machine characteristics (such as speeds, feeds, etc.), which should generally be carried out before testing the accuracy. This part of ISO 3686 provides the terminology used for the principle components of the machine and indicates the designation of the axes in accordance with ISO 841.

Test conditions for high accuracy turret and single spindle coordinate drilling and boring machines with table of fixed height with vertical spindle - Testing of the accuracy - Part 2: Portal type machines with moving table

ISO 3686-1:2000 高精度立式转塔和单轴工作台不升降坐标钻镗床检验条件 精度检验 第1部分:单柱式机床

This part of ISO 3686 specifies, with reference to ISO 230-1; both geometric tests and machining tests on vertical spindle, single column type coordinate drilling and boring machines. It also specifies the applicable tolerances corresponding to the above-mentioned tests. It should be noted that, besides drilling and boring operations, it may be possible to carry out light milling operations with these machines. However, this part of ISO 3686 does not deal with jig boring machines or machining centres. This part of ISO 3686 deals only with the verification of the accuracy of the machine. It does not apply to the testing of the machine operation (vibrations, abnormal noises, the stick-slip motion of components, etc.), nor the machine characteristics (such as speeds, feeds, etc.), which should generally be carried out before testing the accuracy. This part of ISO 3686 provides the terminology used for the principle components of the machine and indicates the designation of the axes in accordance with ISO 841.

Test conditions for high accuracy turret and single spindle coordinate drilling and boring machines with table of fixed height with vertical spindle - Testing of the accuracy - Part 1: Single column type machines

NF E60-116:1999 带水平主轴的镗床和铣床的试验条件.准确度试验.第2部分:台式机床

Test conditions for boring and milling machines with horizontal spindle. Testing of the accuracy. Part 2 : table-type machines.

NF E60-119:1998 带水平主轴的镗床和铣床的试验条件.精确度试验.第4部分:可移动床柱的多刀刨床

Test conditions for boring and milling machines with horizontal spindle. Testing of the accuracy. Part 4 : planer type machines with movable column.

NF E60-118:1998 带水平主轴的镗床和铣床的试验条件.精确度试验.第3部分:带有可拆卸的固定工件夹具台的卧式机器

Test conditions for boring and milling machines with horizontal spindle. Testing of the accuracy. Part 3 : floor type machines with detached, stationary work-holding table.

ISO 3070-4:1998 卧式镗铣床检验条件 精度检验 第4部分:带移动立柱的台式机床

This part of ISO 3070 specifies, with reference to ISO 230-1 and ISO 230-2, geometric tests, machining tests and tests for checking accuracy and repeatability of positioning by numerical control, on general purpose, normal accuracy, planer type horizontal spindle boring and milling machines with movable column. These types of machine tool are defined in subclauses 3.2 and 3.3 of ISO 3070-0:1982. This part of ISO 3070 also specifies the applicable tolerances corresponding to the above mentioned tests. These machines can be provided with spindle heads of different types corresponding in most cases to figures: 4(spindle head with sliding boring spindle and milling spindle) 5(spindle head with sliding boring spindle and with facing head) 6(spindle head with ram or milling ram) of ISO 3070-0:1982. In addition, it should be noted that this part of ISO 3070 concerns machines which have movement of the table along the X-axis, a vertical movement of the spindle head along the Y-axis, a movement of the column along the W-axis and may include a rotary or indexing table. This part of ISO 3070 deals only with the verification of the accuracy of the machine. It does not apply to the testing of the machine operation (vibration, abnormal noise, stick-slip motion of components, etc.) nor to machine characteristics (such as speeds, feeds, etc.), as such checks are generally carried out before testing the accuracy.

Test conditions for boring and milling machines with horizontal spindle - Testing of the accuracy - Part 4: Planer type machines with movable column

ISO 3070-3:1997 卧式镗铣床检验条件 精度检验 第3部分:带分离式工件夹持固定工作台的落地式机床

This part of ISO 3070 specifies, with reference to ISO 230-1 and ISO 230-2, geometric tests, machining tests and tests for checking accuracy and repeatability of positioning by numerical control, on general purpose, normal accuracy, floor type boring and milling machines with horizontal spindle. These types of machine tool are defined in 3.1 of ISO 3070-0:1982. This part of ISO 3070 also specifies the applicable tolerances corresponding to the above-mentioned tests. These machines can be provided with spindle heads of different types corresponding in most cases to figures 4(spindle head with sliding boring spindle and milling spindle), 5(spindle head with sliding boring spindle and with facing head) and 6(spindle head with ram or milling ram) of ISO 3070-0:1982. It should be noted that this part of ISO 3070 concerns machines which have a movement of the column or column saddle on the bed (X-axis), a vertical movement of the spindle head (Y-axis), a movement of boring spindle or ram (Z-axis) and possibly a feed movement of radial facing slide in the facing head (U-axis). Some machines also have an intermediate saddle having slideway between column and bed to achieve additional movement of the column parallel to the spindle axis (W-axis). This part of ISO 3070 also includes the work-holding fixed table, an independent but necessary part of the machine as defined in ISO 7572. This part of ISO 3070 deals only with the verification of the accuracy of the machine. It does not apply to the testing of the running of the machine (vibration, abnormal noise, stick-slip motion of components, etc.) nor to machine characteristics (such as speeds, feeds, etc.), as such checks are generally carried out before testing the accuracy.

Test conditions for boring and milling machines with horizontal spindle - Testing of the accuracy - Part 3: Floor type machines with detached, stationary work-holding table

ISO 3070-2:1997 卧式镗铣床检验条件 精度检验 第2部分:台式机床

This part of ISO 3070 specifies, with reference to ISO 230-1 and ISO 230-2, geometric tests, tests and tests for checking accuracy and repeatability of positioning by numerical control, on general purpose, normal accuracy, table type boring and milling machines with horizontal spindle. These types of machine tools are defined in sub-clause 3.1 of ISO 3070-0:1982. This part of ISO 3070 also specifies the applicable tolerances corresponding to the above mentioned tests. These machines can be provided with spindle heads of different types corresponding in most cases to figures: 4(spindle head with sliding boring spindle and milling spindle) 5(spindle head with sliding boring spindle and with facing head) 6(spindle head with ram or milling ram) of ISO 3070-0:1982. In addition, it should be noted that this part of ISO 3070 concerns machines which have both longitudinal (W-axis) and transverse (X-axis) movement of the table, a vertical movement of the spindle head (Y-axis) and may include a rotary or indexing table. This International Standard deals only with the verification of the accuracy of the machine. It does not apply to the testing of the running of the machine (vibration, abnormal noise, stick-slip motion of components, etc.) nor to machine characteristics (such as speeds, feeds, etc.), as such checks are generally carried out before testing the accuracy.

Test conditions for boring and milling machines with horizontal spindle - Part 2: Table-type machines

CSN 20 0462-1989 金属加工机械钻孔机尺寸系列

Schválení ST SEV 5944-87 a ST SEV 5945-87 doporu?ilo federální ministerstvo v?eobecného strojírenství ?SSR. Zpracovatel a oborové normaliza?ní st?edisko: TST — koncernov? v?zkumn? ústav obráběcích stroj? a obrábění — V?OSO Praha, I?O 009 628, Jaroslav Dolava Pracovník Federálního ú?adu pro normalizaci a mě?ení: Ing. Pavel Dvo?ák

The metal working machines. The drilling and boring off machines. The series. The sizes