25.220.60 标准查询与下载

GB/T 31361-2015 无溶剂环氧液体涂料的防腐蚀涂装

本标准规定了用于金属材料和混凝土材料防腐蚀无溶剂环氧液体涂料的涂层分类、材料要求、涂装工艺规范、试验方法、检测规则、成品标志等要求。本标准适用于金属材料和混凝土材料无溶剂环氧液体涂料防腐蚀涂装,也适用于其他与之相容的涂层材料及基材防腐蚀涂装。本标准不适用于装饰涂层和功能涂层。

Anti-corrosion painting of solvent-free liquid epoxy coating

GB/T 28699-2012 钢结构防护涂装通用技术条件

GB/T28699—2012 钢结构防护涂装通用技术条件本标准规定了钢结构防护涂装的涂层体系技术要求、检、验方法、检、测及验收规则及典型的涂层体系y规定了涂装作业的安全、卫生和环境保护的要求a 本标准适用于钢结构及钢结构附属件的防护涂装。

Steel structure protection general requirements of coatings

GB/T 18593-2010 熔融结合环氧粉末涂料的防腐蚀涂装

本标准规定了钢铁等金眉材料进行熔融结合环氧粉末涂料防腐蚀涂装的材料、工艺规范、涂层性能耍求及试验方法。 本标准不适用于装饰性涂装″

Anti-corrosive painting of fusion bonded epoxy coating powders

GB/T 24596-2009 球墨铸铁管和管件.聚氨酯涂层

本标准规定了球墨铸铁管和管件内外聚氨酯防腐涂层的技术要求、试验方法和检验规则等。 本标准适用于输送不超过50℃的水及污水的聚氨酯内涂层、环境温度不超过50℃的聚氨酯外涂层。

Ductile iron pipes and fittings.Polyurethane coatings

GB/T 18593-2001 熔融结合环氧粉末涂料的防腐蚀涂装

本标准规定了钢铁材料熔融结合环氧粉末涂料防腐蚀涂装的材料、工艺规范、涂层性能要求及试验方法。 本标准不适用于装饰性涂装。 当本标准应用于接触食品的管道或结构件的涂装时，涂层必须符合GB 9686食品容器内壁聚酰胺环氧树脂涂料卫生标准的规定。

Anti-corrosive painting of fusion bonded epoxy coating powders

GB/T 17459-1998 球墨铸铁管 沥青涂层

本标准规定了球墨铸铁管壁涂装的平均厚度为0.07mm沥青涂层的要求及测试方法，球墨铸铁管符合GB/T13295或GB/T13294，用于地下管道。 注：根据GB/T17457-1998《球墨铸铁管水泥砂浆离心法衬层一般要求》，球墨铸铁管的水泥砂浆衬层如用于输送特殊腐蚀性液体时，允许在水泥砂浆衬层上增加涂层。

Ductile iron pipes--Bitumen coating

ASTM D2793-99(2024) 木板基材上有机涂层耐结块性的标准试验方法

Standard Test Method for Block Resistance of Organic Coatings on Wood Panel Substrates

ASTM D4708-24 有机涂层均匀自由膜制备的标准实施规程

1.1  This practice covers the preparation of free films of organic coatings for use in determining the physical properties of the coatings. 1.2  The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Uniform Free Films of Organic Coatings

ASTM D2134-19(2024) 用斯沃德型硬度摇杆测定有机涂层硬度的标准试验方法

1.1  This test method covers the determination of the relative degree of surface hardness of organic coatings using a specific apparatus used in the coatings industry. 1.2  The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3  This test method does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Hardness of Organic Coatings with a Sward-Type Hardness Rocker

ASTM D6083/D6083M-24 屋面用液体丙烯酸涂料的标准规范

Standard Specification for Liquid-Applied Acrylic Coating Used in Roofing

T/GDEIA 5-2023 反渗透膜功能涂布机

本文件规定了反渗透膜功能涂布机生产技术要求的术语和定义、型号和型式、基本参数、设备组成、技术要求、试验方法、检验规则、标志、包装、运输和贮存等。

Reverse osmosis coating machine

DB37/T 4660-2023 浮桥承压舟船壳涂装技术要求

Technical requirements for hull coating of pontoon pressure boats

ASTM D7835/D7835M-23 用机械摩擦机测定有机涂层耐溶剂性的标准试验方法

Standard Test Method for Determining the Solvent Resistance of an Organic Coating Using a Mechanical Rubbing Machine

ASTM A975-23 双扭六角网石笼和护坡（金属涂层钢丝或聚氯乙烯涂层金属涂层钢丝）标准规范

Standard Specification for Double-Twisted Hexagonal Mesh Gabions and Revet Mattresses (Metallic-Coated Steel Wire or Metallic-Coated Steel Wire With Poly(Vinyl Chloride) (PVC) Coating)

23/30477705 DC BS EN 13523-3 卷材涂层金属 测试方法 第3部分：色差和同色异谱 仪器比较

BS EN 13523-3. Coil coated metals. Test methods - Part 3. Colour difference and metamerism. Instrumental comparison

23/30477717 DC BS EN 13523-10 卷材涂层金属 测试方法 第10部分：耐荧光紫外线辐射和水凝结

BS EN 13523-10. Coil coated metals. Test methods - Part 10. Resistance to fluorescent UV radiation and water condensation

23/30477702 DC BS EN 13523-29 卷材涂层金属 测试方法 第29部分：耐环境污染性（沾污和剥离）

BS EN 13523-29. Coil coated metals. Test methods - Part 29. Resistance to environmental soiling (Dirt pick-up and striping)

23/30477714 DC BS EN 13523-22 卷材涂层金属 测试方法 第22部分：色差 视觉对比

BS EN 13523-22. Coil coated metals. Test methods - Part 22. Colour difference. Visual comparison

23/30477696 DC BS EN 13523-8 卷材涂层金属 测试方法 第8部分：耐盐雾（雾）性能

BS EN 13523-8. Coil coated metals. Test methods - Part 8. Resistance to salt spray (fog)

23/30477699 DC BS EN 13523-21 卷材涂层金属 测试方法 第21部分：户外暴露面板的评估

BS EN 13523-21. Coil coated metals. Test methods - Part 21. Evaluation of outdoor exposed panels