27.060.10 液体和固体燃料燃烧器 标准查询与下载

GB/T 37433-2019 低功率燃油燃烧器通用技术要求

General specification for small oil burners

GB/T 19839-2005 工业燃油燃气燃烧器通用技术条件

本标准规定了工业燃油和燃气燃烧器的术语和定义，要求，试验方法，检验规则，标志，包装、运输和贮存等。 本标准适用于输出功率不小于60Kw的机械通风的工业燃油、燃气燃烧器（以下简称燃烧器）的设计、制造和验收。本标准不适用于自然通风的燃烧器的设计、制造和验收。

General specification for industrial oil and gas burners

T/CIET 418-2024 氨燃料燃烧装置技术要求

本文件规定了氨燃料工业燃烧装置的术语和定义、分类、系统组成、要求、试验方法、检验规则、技术文件与标识、包装运输和贮存、安装、调试和维护。 本文件适用于各种工业炉窑全氨或掺氨燃料燃烧装置（以下简称燃烧器），不适用于氨燃料电池、氨发动机、氨燃烧锅炉和民用氨燃烧装置。

Technical requirements for ammonia fuel combustion apparatus

T/CIET 417-2024 氨燃料陶瓷辊道窑技术要求

本文件规定了氨燃料陶瓷辊道窑技术的术语和定义、基本要求、燃烧装置和燃烧操作、储存和厂内输送、安全和应急管理和环境保护。 本文件适用于使用氨燃料的陶瓷辊道窑。

Technical requirements for ammonia fuel ceramic roller kiln

T/HITNBA 0001-2023 连续式生物质热解炭化成套设备

3.术语和定义:3.1 生物质;3.2 生物质热解;3.3 连续式热;3.4 连续式生物质热解炭化成套生产装备;3.5 进料处理量;3.6 热解炭化器;3.7 供热温度;3.8 热解炭化温度;3.9  热解炭化压力;3.10 原料炭化最小含水率;3.11 预热温度;3.12 进料温度;3.13 热解炭化反应时间;3.14 炭产率;3.15 热解炭化;3.16 炭化速率;3.17 生物质挥发分;3.18 不凝可燃气;3.19 焦油和木醋液;3.20 故障;3.21 可靠度; 4.产品型号; 5.主要技术参数; 6.技术要求:6.1 外观;6.2 一般要求;6.3 使用环境要求;6.4 功能要求;6.5 成套设备性能要求;6.6 技术要求;6.7 电气要求;6.8 安装要求;6.9 环保要求;6.10 涂漆和外观要求; 7.试验:7.1 一般要求的检测;7.2 使用环境要求的检测;7.3 功能要求的检测;7.4 成套设备性能要求的检测;7.5 技术要求的检测;7.6 安全要求的检测;7.7 安装要求的检测;7.8 环保要求的检测;7.9 涂漆和外观要求的检测;7.10 空负荷运转前试验;7.11 空负荷运转试验;7.12 负荷运转试验; 8.检验规则:8.1 检验分类;8.2 出厂检验;8.3 安装调试检验;8.4 型式检验; 9.标志、包装、运输与贮存;

Continuous biomass pyrolysis and carbonization complete set of equipment

ASTM D5986-23 用气相色谱法/傅立叶变换红外光谱法测定成品汽油中含氧物、苯、甲苯、C8–C12芳烃和总芳烃的标准试验方法

Standard Test Method for Determination of Oxygenates, Benzene, Toluene, C8–C12 Aromatics and Total Aromatics in Finished Gasoline by Gas Chromatography/Fourier Transform Infrare

GSO ASTM D6550:2023 用超临界流体色谱法测定汽油中烯烃含量的标准试验方法

  Scope is not provided for this standard

Standard Test Method for Determination of Olefin Content of Gasolines by Supercritical-Fluid Chromatography

BS 5410-3:2023 液体燃料燃烧 用于液体燃料备用发电机、熔炉、窑炉、烤箱和其他工业用途的装置 实践守则

Learn more about how to use this standard by downloading our free Executive Briefing here:  https://www.bsigroup.com/en-GB/standards/bs-5410-3/   What is BS 5410-3 - Installations for liquid fuelled standby generators about? BS 5410-3:2023 is the third national standard in a series of standards on the design, installation, commissioning and maintenance of liquid-fuel-using equipment. It provides recommendations and guidance for liquid fuel-consuming equipment used in conjunction with industrial installations. The other standards within the series include: BS 5410-1:2019 Code of practice for liquid fuel firing - Installations for space heating and hot water supply purposes for domestic buildings BS 5410-2:2018 Code of practice for liquid fuel firing - Non-domestic installations Who is BS 5410-3 - Installations for liquid fuelled equipment for? Designers and users of liquid fuel firing installations Specifiers Installers Building owners Local authority and Environment Agency inspection personnel Liquid fuel delivery firms

Liquid fuel firing. Installations for liquid fuelled standby generators, furnaces, kilns, ovens and other industrial purposes. Code of practice

KS B 8021-2022 燃油器具试验方法通则

General rules for test methods of oil burning appliances

KS B 8020-2022 燃油器具结构通则

General rules for structure of oil burning appliances

ASTM D6426-22 测定中间馏分燃料油可过滤性的标准试验方法

1.1 This test method covers a procedure for determining the filterability of distillate fuel oils within the viscosity range from 1.70 mm2 /s to 6.20 mm2 /s (cSt) at 40 °C. NOTE 1—ASTM specification fuels falling within the scope of this test method are Specification D396 Grade No. 2, Specification D975 Grade No. 2-D, and Specification D2880 Grade No. 2-GT. NOTE 2—The test method has been used with lower viscosity middle distillate fuels such as Specification D396 Grade No. 1, Specification D975 Grade No. 1-D, and Specification D2880 Grade No. 1-GT, but the precision has not been studied and therefore the stated precision has not been validated for these grades. 1.2 This test method is not applicable to fuels that contain undissolved water. 1.3 The values stated in SI units are to be regarded as standard. 1.3.1 Non-SI units, specifically U.S. customary units such as temperature in degrees Fahrenheit and pressure in pounds per square inch gauge (psig), are included for information. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Filterability of Middle Distillate Fuel Oils

ASTM D6448-16(2022) 用过的润滑油生产工业燃烧器燃料的标准规范

1.1 This specification covers four grades of fuel oil made in whole or in part with hydrocarbon-based used or reprocessed lubricating oil or functional fluids, such as preservative and hydraulic fluids. The four grades of fuel are intended for use in various types of fuel-oil-burning industrial equipment under various climatic and operating conditions. These fuels are not intended for use in residential heaters, small commercial boilers, combustion engines, or marine applications, 1.1.1 Grades RFO4, RFO5L, RFO5H, and RFO6 are used lubricating oil blends, with or without distillate or residual fuel oil, or both, of increasing viscosity and are intended for use in industrial burners equipped to handle these types of recycled fuels. NOTE 1—For information on the significance of the terminology and test methods used in this specification, see Appendix X1. 1.2 This specification is for use in contracts for the purchase of fuel oils derived from used lubricating oil and for the guidance of consumers of such fuels. This specification does not address the frequency with which any particular test must be run. 1.3 Nothing in this specification shall preclude observance of national or local regulations, which can be more restrictive. In some jurisdictions, used oil is considered a hazardous waste and fuels from used oil are required to meet certain criteria before use as a fuel. NOTE 2—For United States federal requirements imposed on used oil generators, transporters and transfer facilities, reprocessors, marketers, and burners, see 40 CFR 279. NOTE 3—The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865. 1.4 The values stated in SI units are to be regarded as standard; non-SI units, when given, are for information only. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Industrial Burner Fuels from Used Lubricating Oils

CSA B140.1 Série-2022 喷雾和蒸气油燃烧器

1 Domaine d’application 1.1 Application Cette norme vise : a) les brûleurs à mazout à pulvérisation (peu importe les dimensions, le taux d’allumage ou la qualité* du mazout) conçus principalement pour être installés dans des appareils à air chaud, à eau chaude et à vapeur; * La qualité du mazout devrait être conforme à CSA B140.0, à l’exception de la qualité B6-B20, qui est décrite dans ASTM D396. b) les brûleurs à mazout à pulvérisation qui font partie d’un ensemble dans des appareils comme des fours, des appareils de chauffage, des cuisinières et des générateurs d’air chaud spéciaux; c) les brûleurs à pulvérisation intégrés qui font partie d’un appareil complet; et d) certains composants et accessoires (p. ex., ensembles de pompes et dispositifs de sûreté- combustion) pour les brûleurs à mazout à pulvérisation. 1.2 But Cette norme stipule les prescriptions minimales relatives aux gicleurs conçus pour installation sur des brûleurs à mazout à pulvérisation sous pression. Cette norme comprend les prescriptions relatives à la fabrication, au marquage et au rendement, afin d’assurer un fonctionnement uniforme des gicleurs. L’objectif de ces prescriptions est de déterminer l’uniformité du débit, de l’angle nominal et du modèle nominal de jet, de tout lot de gicleurs semblablement identifiés, produit subséquemment par rapport à un lot original, plutôt que de comparer ces caractéristiques à une quelconque valeur absolue ou spécifiée. Les prescriptions s’appliquent aux gicleurs qui sont : a) de la plage de capacité allant jusqu’à 7,6 L/h (2 gal US/h) inclusivement; et b) principalement prévus pour utilisation avec du mazout pas plus lourd que celui de qualité nº2 et pour des mazouts de qualité B6-B20. Note : Les gicleurs conçus pour utilisation sur un brûleur spécifique peuvent aussi être évalués selon les exigences dans cette norme. 1.3 Exclusion Cette norme ne s’applique pas aux brûleurs à pulvérisation allumés manuellement. 1.4 Terminologie Dans cette norme, le terme « doit » indique une exigence, c’est-à -dire une prescription que l’utilisateur est obligé de respecter pour assurer la conformité à la norme; « devrait » indique une recommandation ou ce qu’il est conseillé mais non obligatoire de faire; et « peut » indique une possibilité ou ce qu’il est permis de faire. Les notes qui accompagnent les articles ne comprennent pas de prescriptions ni de recommandations. Elles servent à séparer du texte les explications ou les renseignements qui ne font pas proprement partie de la norme. Les notes au bas des figures et des tableaux font partie de ceux-ci et peuvent être rédigées comme des prescriptions. Les annexes sont qualifiées de normatives (obligatoires) ou d’informatives (facultatives) pour en préciser l’application. 1.5 Unités de mesure Les valeurs indiquées en unités SI sont les valeurs officielles dans cette norme. Les valeurs entre parenthèses sont données à titre d’information et pour fin de comparaison seulement.

Spray and Vapor Oil Burners

CSA B140.1 Series-2022 雾化式和汽化式燃油燃烧器

1 Scope 1.1 Application This Standard applies to a) oil burners of the atomizing type (irrespective of size, firing rate, or grade* of fuel oil) that are designed primarily for installation in warm-air, hot-water, and steam-heating equipment; * The grade of fuel oil should be as specified in CSA B140.0, except for grade B6-B20, which is specified in ASTM D396. b) atomizing-type oil burners that are a part of an assembly in appliances such as ovens, heaters, ranges, and special furnaces; c) integral atomizing-type burners, where they are part of a complete appliance; and d) certain components and accessories (e.g., fuel units and combustion safety controls) for atomizingtype oil burners. 1.2 Intent This Standard states the minimum requirements for nozzles that are designed for installation in oil burners of the pressure atomizing type. This Standard includes requirements for construction, marking, and performance to provide consistent operation of nozzles. The intent of the requirements is to determine the consistency of flow rate, nominal spray angle, and nominal spray pattern for any subsequent production lot of similarly identified nozzles to an original lot, rather than to compare these characteristics to any absolute or specified values. The requirements apply to nozzles that are a) of the capacity range up to and including 7.6 L/h (2 US gph); and b) primarily intended for use with fuel oil not heavier than grade No. 2, and for fuel oils of grade B6-B20. Note: Nozzles designed for use in a specific burner may also be evaluated to the requirements in this Standard. 1.3 Exclusion This Standard does not apply to manually lighted atomizing burners. 1.4 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.5 Units of measurement The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only.

Atomizing- and vapourizing-type oil burners

ASTM D6615-22 Jet B宽切航空涡轮燃料标准规范

1.1 This specification covers the use of purchasing agencies in formulating specifications for purchases of aviation turbine fuel under contract. 1.2 This specification defines one specific type of aviation turbine fuel for civil use. This fuel has advantages for operations in very low temperature environments compared with other fuels described in Specification D1655. This fuel is intended for use in aircraft that are certified to use such fuel. 1.3 This specification does not define the quality assurance testing and procedures necessary to ensure that fuel in the distribution system continues to comply with this specification after batch certification. Such procedures are defined elsewhere, for example in ICAO 9977, EI/JIG Standard 1530, JIG 1, JIG 2, API 1543, API 1595, and ATA-103. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Jet B Wide-Cut Aviation Turbine Fuel

CSA B140.0-2022 燃油设备：一般要求

1 Scope 1.1 Application This Standard provides minimum requirements for oil-burning equipment, including a) fuel oil filters; b) draft regulators; c) flue pipe mounted heat reclaimers; d) through-the-wall venting systems; e) systems that supply outside combustion air; and f) used-oil-burning equipment. 1.2 Intended use This Standard is to be used in conjunction with the other Standards in the CSA B140 series, as applicable, to form a complete Standard for a particular type of oil-burning appliance or equipment. 1.3 Correlation with the CSA B140 series of Standards Each of the other Standards in the CSA B140 series covers construction requirements, marking, instructions, and detailed testing procedures for a single classification or a closely related group of oil- burning equipment. 1.4 Units of measurement The values given in SI (metric) units are the units of record for the purpose of this Standard. The values given in parentheses are for information and comparison only. 1.5 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Oil-burning equipment: General requirements

KS B 6201-2022 压力喷射燃烧器

Pressure injection burners

KS B 8902-2022 木屑颗粒锅炉的安装方法

The methods for installing wood pellet boiler

KS B ISO 22968-2022 强制通风燃油燃烧器

Forced draught oil burners

KS B 6203-2022 固定式蒸汽锅炉最高工作压力和过热蒸汽温度

Maximum working pressure and super heated steam temperature of stationary steam boilers