共找到 895 条与 相关的标准,共 60 页
Technical Specifications for Fittings of 1000kV AC Overhead Transmission Lines
Technical Specifications for 1000kV Substation Fittings
本标准规定了架空输电线路运行状态监测系统组成与分类.技术要求.试验方法.检验规则产品的标志、`包装、.运输保管及贮存等。本标准适用于交直流架空输电线路运行状态监测系统。
Monitoring system of operating status for overhead transmission lines
Engineering data handover specification for power transmission and transformation
Insulating aerial device for 10kV live working
Maintenance specification of transmission line of voltage-source converter based high voltage direct current (VSC-HVDC)
Guide to UV imaging detection of electrical equipments in high altitude regions—Part 2: Transmission lines
Short-circuit current calculation in three-phase a.c.systems—Part 4: Currents during two separate simultaneous line-to-earth short circuits and partial short-circuit currents flowing through earth
Rigid gas-insulated transmission lines for rated voltage of 72.5kV and above
Technology guide for preventing bird-related outages of overhead transmission lines
Specified failure load series and coupling dimensions for electric power fittings
Short-circuit current calculation in three-phase a.c.systems—Part 5: Examples
Short-circuit current calculation in three-phase a.c.systems—Part 3:Data of electrical equipment
Distributed fault diagnosis system of transmission lines
Short-circuit current calculation in three-phase a.c. systems—Part 2: Factors for the calculation of short-circuit currents
General technical specification for on-line monitoring device on overhead transmission lines
本标准规定了交、直流架空输电线路故障巡视的故障分类、巡视前准备、巡视内容及故障性质与故障类型判别。 本标准适用于66 kV及以上交、直流架空输电线路的故障巡视。
Technical guide of fault inspection for overhead transmission line
本标准规定了电力金具的主要名词术语。 本标准适用于制定电力金具标准,编写、翻译专业文献、教材及书刊。与电力金具有关的其他领域亦可参照使用。
Terminology for electric power fittings
本标准规定了±800 kV直流架空输电线路导线配套金具的一般技术要求、设计与制造、连接与紧固、检验与试验、标志与包装等。本标准适用于±800 kV直流架空输电线路导线用配套金具。
Technical specification for fittings of ± 800 kV DC overhead transmission line
GB/T 15544的本部分适用于额定频率为50 Hz或60 Hz的低压、高压三相交流系统中的短路电流计算。当系统标称电压为500 kV及以上,并且含有远距离交流输电线路时,需特殊考虑。本部分提出的短路点等效电压源法,是一种简洁实用的短路电流计算方法,其计算结果一般情况下具有可接受的精度。如果能够得到相同的计算精度,不排斥采用其他计算方法,如叠加法。用叠加法计算得到的短路电流,依赖于某一特定潮流,因此不一定是最大短路电流。本部分涉及的短路形式包括平衡短路故障和不平衡短路故障。对于人为或意外发生的一个线路导体与大地间短路,以下两种情况的物理特性和影响不同(导致不同的计算目的),必须明确加以区分:--在中性点直接接地或经阻抗接地的系统中,导体对地短路;--在中性点不接地或谐振接地系统中,发生一处导体对地短路故障,该短路故障的计算不在本部分研究范围内。在中性点不接地或谐振接地系统中,同时发生两个独立单相接地短路故障时,短路电流的计算参照IEC 60909-3。短路电流和短路阻抗也可通过系统试验、系统分析仪器测量或通过数字计算机确定。在现有低压系统中,能够在预期的短路点通过测量得到短路阻抗。短路阻抗的计算通常基于电力设备的额定参数以及系统的拓扑结构,这种方法的优点是既可应用于现有系统,也可应用于规划系统。通常情况下,应计算两种不同幅值的短路电流:--最大短路电流,用于选择电气设备的容量或额定值;--最小短路电流,用于选择熔断器、设定保护定值或校核感应电动机启动。本部分不适用于受控条件(短路试验站)下人为短路和飞机、船舶用电气设备的短路计算。
Short-circuit current calculation in three-phase a.c.systems.Part 1:Calculation of currents
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号