31.040 电阻器 标准查询与下载

GB/T 18806-2002 电阻应变式压力传感器总规范

本标准规定了电阻应变式压力传感器（以下简称传感器）的定义、命名方法及型号代号、基本参数和优先值、技术要求、试验方法、验收规则及标志、包装、贮存的要求。 本标准适用于电阻应变式压力传感器的研制、生产和验收。

General specification for the resistance strain pressure transducer/sensor

GB/T 13823.18-1997 振动与冲击传感器的校准方法 互易法校准

本标准详细规定了互易法对加速度传感器进行绝对校准所用仪器及测试步骤。 本标准适用于直线型加速度传感器，校准频率范围40～1250Hz，加速度10～100m/s。本方法在参考点（160Hz，100m/s）和放大器增益档位置于参考位置时，校准不确定度为1％。

Methods for the calibration of vibration and shock pick-ups. Primary vibration calibration by reciprocity method

GB 4547-1991 玻璃容器 抗热震性和热震耐久性试验方法

Glass containers－Thermal shock resistance and thermal shock endurance－Test methods

GB/T 7017-1986 电阻器非线性测量方法

本标准规定的非线性测量方法适用于电阻器。这个方法仅在制造厂和用户协商同意后才使用。

Method of measurement of non-linearity in resistors

KS C IEC 60915-2020 电子设备用电容器和电阻器 主轴端部、套管以及安装单孔、套管安装、主轴操作电子元件的首选尺寸

Capacitors and resistors for electronic equipment－Preferred dimensions of spindle ends, bushes and for the mounting of single-hole, bush-mounted, spindle-operated electronic components

EN IEC 61643-331:2020 低压浪涌保护元件 第331部分：金属氧化物变阻器（MOV）的性能要求和测试方法

IEC 61643-331:2020 is available as IEC 61643-331:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61643-331:2020 is a test specification for metal oxide varistors (MOV), which are used for applications up to 1 000 V AC or 1 500 V DC in power lines, or telecommunication, or signalling circuits. They are designed to protect apparatus or personnel, or both, from high transient voltages. This document applies to MOVs having two electrodes and hybrid surge protection components. This document also does not apply to mountings and their effect on the MOV’s characteristics. Characteristics given apply solely to the MOV mounted only in the ways described for the tests. This third edition cancels and replaces the second edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - a Varistor MCOV rating assurance test; - an energy rating test (2ms); - revised Dielectric strength and insulation resistance tests.

Components for low-voltage surge protection - Part 331: Performance requirements and test methods for metal oxide varistors (MOV)

KS C IEC 61643-331-2019 低压浪涌保护器用元件 第331部分：金属氧化物压敏电阻(MOV)规范

Components for low－voltage surge protective devices－Part 331：Specification for metal oxide varistors(MOV)

EN IEC 61643-331:2018 低压电涌保护器元件 第331部分：金属氧化物变阻器（MOV）的性能要求和测试方法

Components for low-voltage surge protective devices - Part 331: Performance requirements and test methods for metal oxide varistors (MOV)

SJ/T 10774-2017 电子元器件详细规范 低功率非线绕固定电阻器 RT14型碳膜固定电阻器 评定水平E

本标准规定了低功率非线绕固定电阻器RT14型碳膜固定电阻器的外形尺寸、最大额定值和电特性，试验条件和检验要求

Detail specification for electronic components.Fixed low- power non-wirewound resistors.Type RT14 carbon film fixed resistors.Assessment level E

EN 60063:2015 电阻器和电容器的首选编号系列

IEC 60063:2015 provides series of preferred values for the resistance of resistors and for the capacitance of capacitors. The definition of such series with a defined numeric resolution is a basic prerequisite for the marking and coding of capacitors and resistors with their respective capacitance or resistance values as described in IEC 60062. This edition includes the following significant technical changes with respect to the previous edition: - revision of the information on a relationship between an E Series and the tolerance of a resistance or capacitance value of a respective component; - introduction of advice on a possible deduction from the marking of a component to an associated E Series and also to an associated tolerance; - complete editorial revision.

Preferred number series for resistors and capacitors

KS C IEC 61643-331-A:2015 低压电涌保护装置用元件.第331部分:金属氧化物压敏电阻(MOV)规范

Component for low-voltage surge protective devices — Part 331: Specification for metal oxide varistors(MOV)

GSO IEC 60301:2014 电容器和电阻器接线端子的优选直径

This International Standard gives a series of preferred diameters of the finished wire terminations of capacitors and resistors for use in electronic equipment.

Preferred diameters of wire terminations of capacitors and resistors

GSO IEC 60063:2014 电阻器和电容器的首选数字系列 第二版（1963 年）包含 第1号修正案（1967 年）和 第2号修正案（1977 年）

Abstract: Gives preferred values for fixed resistors and capacitors for ordinary and close tolerances of resistors and capacitors used in electronic equipment.

Preferred number series for resistors and capacitors. Second edition (1963) incorporating Amendments No. 1 (1967) and No. 2 (1977)

GSO IEC 60915:2014 电子设备用电容器和电阻器 轴端、衬套和安装单孔、衬套安装、轴操作电子元件的首选尺寸

This International Standard is applicable to variable capacitors, potentiometers and variable resistors for use in electronic equipment. The dimensions given in this standard have been selected from IEC 60390 and IEC 60620 because the ranges of dimensions included in these standards were considered too large and contained too many variants for capacitors and resistors for electronic equipment. Consequently this standard contains preferred dimensions for shaft ends and bushes and for the mounting of single-hole, bush-mounted, shaft-operated variable capacitors, variable resistors and potentiometers. If other dimensions not listed in this standard have to be used, it is recommended to select them also from the above-mentioned standards.

Capacitors and resistors for use in electronic equipment - Preferred dimensions of shaft ends, bushes and for the mounting of single-hole, bush-mounted, shaft-operated electronic components

GSO IEC 61643-331:2014 低压浪涌保护装置元件 第331部分：金属氧化物压敏电阻 (MOV) 规范

This part of IEC 61643 is a test specification for metal oxide varistors (MOV), which are used for applications up to 1 000 V a.c. or 1 500 V d.c. in power line, or telecommunication, or signalling circuits. They are designed to protect apparatus or personnel, or both, from high transient voltages. This specification applies to MOVs having two electrodes and does not deal with hybrid devices. This specification also does not apply to mountings and their effect on the MOV’s characteristics. Characteristics given apply solely to the MOV mounted only in the ways described for the tests.

Components for low-voltage surge protective devices - Part 331: Specification for metal oxide varistors (MOV)

GSO IEC 60717:2014 具有单向端子的电容器和电阻器所需空间的确定方法

This International Standard applies to capacitors and resistors with unidirectional wire terminations intended for use in electronic equipment. This standard provides a method for determination of the space required by capacitors and resistors with unidirectional wire terminations. NOTE Instead of measuring the actual space, it may be sufficient to ensure that a component fits into the maximum space for which it is designed. This may be achieved by means of fixed gauges.

Method for the determination of the space required by capacitors and resistors with unidirectional terminations

KS C IEC 61643-331-A:2014 低压电涌保护器元件第331部分:金属氧化物压敏电阻器（MOV）规范

Component for low-voltage surge protective devices — Part 331: Specification for metal oxide varistors(MOV)

KS C IEC 61643-331-A-2014 低压电涌保护器元件第331部分:金属氧化物压敏电阻器（MOV）规范

Component for low-voltage surge protective devices — Part 331: Specification for metal oxide varistors(MOV)

GSO IEC 60440:2013 如何测量电阻器的非线性

IEC 60440:2012 specifies a method of measurement and associated test conditions to assess the magnitude of non-linear distortion generated in a resistor. This method is applied if prescribed by a relevant component specification, or if agreed between a customer and a manufacturer. This International Standard cancels and replaces the Technical Report IEC/TR 60440, published in 1973. The major changes with regard to the Technical Report are: - change of the principle parameter's term from "third harmonic attenuation" to "third harmonic ratio"; - addition of advice on the prescription of requirements in a relevant component specification; - addition of a set of recommended measuring conditions for a specimen with a rated dissipation of less than 100 mW; - a complete editorial revision.

Method of measurement of non-linearity in resistors

EN 60301:2012 电容器和电阻器导线终端的首选直径

IEC 60301:2012 gives a series of preferred diameters of the finished wire terminations of capacitors and resistors for use in electronic equipment. This third edition cancels and replaces the second edition, published in 1971, and its Amendment 1, published in 1972, and constitutes a technical revision. The main technical changes with respect to the second edition are the following: - employment of SI units only in the normative part of this standard, causing transfer of all imperial dimensions from Table 1 to the informative Annex A, - addition of two smaller diameters of wire terminations in Table 1, and - tightening of the tolerance ranges defined by minimum and maximum diameters in Table 1.

Preferred diameters of wire terminations of capacitors and resistors