31.220.99 其他机电零部件 标准查询与下载

T/ZLJYXH 5-2023 循环再使用电梯电控件通用技术要求

1.标志 2.外观 3.结构完整性 4.连通性 5.功能性要求 6.安全性能要求 7.环境试验要求 8.限用物质限量要求

General technical requirements for recycling elevator electrical controls

SJ/T 11539-2015 接触式图像传感器通用规范

本标准规定了接触式图像传感器的要求、试验方法、质量评定程序及标志、包装、运输、贮存等。 本标准适用于接触式图像传感器的设计和制造。本标准是制定产品标准的依据。

General specification for contact image sensor

SJ/T 11538-2015 热打印头通用规范

本标准规定了热打印头的要求、试验方法、质量评定程序及标志、包装、运输、贮存等。本标准适用于热打印头的设计和制造。本标准是制定产品标准的依据。

General specification for thermal print head

DB43/T 963-2014 电梯用超级电容节能应急平层装置

Supercapacitor energy-saving emergency leveling device for elevators

DS/EN 61811-55/Corr.1:2007 全有或全无机电继电器 第55部分：空白详细规范 评估质量的机电全有或全无电信继电器 两个转换触点，11 x 7,5 mm（最大）底座

This part of IEC 61811 is a blank detail specification applicable to electromechanical all-or-nothing telecom relays of assessed quality. Relays according to this standard are provided for the operation in telecommunication applications. However, as electromechanical all-or-nothing relays they are also suitable for particular industrial and other applications. This standard selects from IEC 61810-7 and other sources the appropriate methods of test to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications in accordance with IEC 61811-1. Detailed test schedules a

Electromechanical all-or-nothing relays - Part 55: Blank detail specification - Electromechanical all-or-nothing telecom relays of assessed quality - Two change-over contacts, 11 x 7,5 mm (max.) base

JB/T 10501-2005 电力半导体器件用管壳瓷件

本标准规定了电力半导体器件用管壳瓷件(以下简称瓷件)的型号、尺寸、技术要求、检验规则、标志和包装等。 本标准适用于电力半导体器件的平板形管壳和KL16型以上螺栓形管壳的瓷件。

Ceramic parts of case for power semiconductor devices

DS/EN 61811-10:2003 质量评估的机电初级继电器 第10部分：分规范 工业应用继电器

This part of IEC 61811 is a sectional specification that covers electromechanical elementary (non-specified time all-or-nothing) relays of assessed quality for industrial application. NOTE: Electromechanical all-or-nothing telecom relays of assessed quality are covered by IEC 61811-50. It is based on the basic relay standard IEC 61810-1 as well as on the generic specification IEC 61811-1 and selects from IEC 61810-7 the appropriate test and measurement procedures to be used in detail specifications derived from this specification. Moreover, it contains a basic test schedule to be used in the preparation of such specifications. Detailed test schedules are gi

Electromechanical elementary relays of assessed quality - Part 10: Sectional specification - Relays for industrial application

DS/EN 61811-11:2003 经评估质量的机电初级继电器 第11部分：空白详细规范 工业用继电器

This part of IEC 61811 is a blank detail specification applicable to electromechanical elementary (non-specified time all-or-nothing) relays of assessed quality for industrial application. It is based on the generic IEC 61811-1 and the sectional specification IEC 61811-10 and selects from IEC 61810-7 the appropriate test and measurement procedures to be used in detail specifications derived rom this specification. Morover it contains a basic test schedule to be used in the preparation of such specifications.

Electromechanical elementary relays of assessed quality - Part 11: Blank detail specification - Relays for industrial application

DS/EN 61811-51:2003 全有或全无机电继电器 第51部分：空白详细规范 质量评估的机电全有或全无电信继电器 非标准化类型和结构

This part of IEC 61811 is a blank detail specification applicable to electromechanical all-or-nothing telecom relays of assessed quality. Relays according to this standard are provided for operation in telecommunication applications. However, as electromechanical all-or-nothing relays they are also suitable for particular industrial and other applications. This standard selects from IEC 61810-7 and other sources the appropriate methods of tests to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications in accordance with IEC 61811-1.

Electromechanical all-or-nothing relays - Part 51: Blank detail specification - Electromechanical all-or-nothing telecom relays of assessed quality - Non-standardized types and construction

DS/EN 61811-55:2003 全有或全无机电继电器 第55部分：空白详细规范 评估质量的机电全有或全无电信继电器 两个转换触点，11 x 7,5 mm（最大）底座

This part of IEC 61811 is a blank detail specification applicable to electromechanical all-or-nothing telecom relays of assessed quality. Relays according to this standard are provided for the operation in telecommunication applications. However, as electromechanical all-or-nothing relays they are also suitable for particular industrial and other applications. This standard selects from IEC 61810-7 and other sources the appropriate methods of test to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications in accordance with IEC 61811-1. Detailed test schedules a

Electromechanical all-or-nothing relays - Part 55: Blank detail specification - Electromechanical all-or-nothing telecom relays of assessed quality - Two change-over contacts, 11 x 7,5 mm (max.) base

DS/EN 61811-53:2003 全有或全无机电继电器 第53部分：空白详细规范 评估质量的机电全有或全无电信继电器 两个转换触点，14 mm x 9 mm 底座

This part of IEC 61811 is a blank detail specification applicable to electromechanical all-or-nothing telecom relays of assessed quality. Relays according to this standard are provided for operation in telecommunication applications. However, as electromechanical all-or-nothing relays they are also suitable for particular industrial and other applications. This standard selects from IEC 61810-7 and other sources the appropriate methods of test to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications in accordance with IEC 61811-1.

Electromechanical all-or-nothing relays - Part 53: Blank detail specification - Electromechanical all-or-nothing telecom relays of assessed quality - Two change-over contacts, 14 mm x 9 mm base

DS/EN 61811-54:2003 全有或全无机电继电器 第54部分：空白详细规范 评估质量的机电全有或全无电信继电器 两个转换触点，15 x 7.5 mm 底座

This part of IEC 61811 is a blank detail specification applicable to electromechanical all-or-nothing telecom relays of assessed quality. Relays according to this standard are provided for the operation in telecommunication applications. However, as electromechanical all-or-nothing relays they are also suitable for particular industrial and other applications. This standard selects from the future IEC 61810-7 and other sources the appropriate methods of test to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preperation of such specifications in accordance with IEC 61811-1.

Electromechanical all-or-nothing relays - Part 54: Blank detail specification - Electromechanical all-or-nothing telecom relays of assessed quality - Two change-over contacts, 15 x 7,5 mm base

DS/EN 61811-52:2003 全有或全无机电继电器 第52部分：空白详细规范 评估质量的机电全有或全无电信继电器 两个转换触点，20 mm x 10 mm 底座

This part of IEC 61811 is a blank detail specification applicable to electromechanical all-or-nothing telecom relays of assessed quality. Relays according to this standard are provided for operation in telecommunication applications. However, as electromechanical all-or-nothing relays they are also suitable for particular industrial and other applications. This standard selects from the future IEC 61810-7 and other sources the appropriate methods of test to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications in accordance with IEC 61811-1.

Electromechanical all-or-nothing relays - Part 52: Blank detail specification - Electromechanical all-or-nothing telecom relays of assessed quality - Two change-over contacts, 20 mm x 10 mm base

DS/EN 61811-50:2003 机电全有或全无继电器 第50部分：分规范 质量评估的机电全有或全无电信继电器

This part of IEC 61811 is a sectional specification and applies to electromechanical all-or-nothing telecom relays of assessed quality. Relays according to this standard are provided for operation in telecommunication applications. However, as electromechanical all-or-nothing relays they are also suitable for particular industrial and other applications. This standard selects from IEC 61810-7 and other sources the appropriate methods of test to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications. Detailed test schedules are contained in the blank detail spec

Electromechanical all-or-nothing relays - Part 50: Sectional specification - Electromechanical all-or-nothing telecom relays of assessed quality

SJ 20813-2002 铝和铝合金化学转化膜规范

Specification for chemical conversion on aluminum and aluminum alloys

DS/EN 61811-1:2000 质量评估的机电非指定时间全有或全无继电器 第1部分：通用规范

This generic specification applies to electromechanical non-specified-time all-or-nothing relays of assessed quality. In order to permit assessment of the quality of electromechanical all-or-nothing relays, this specification contains the definition of procedures to be followed for qualification approval and quality conformance inspection. Within the IECQ quality assessment system, this generic specification, together with the relevant sectional and detail specifications, is used for relay qualification approval (third-party assessment by independent certification bodies). Approved relays will be granted an IECQ Certificate of Approval authorizing the use o

Electromechanical non-specified time all-or-nothing relays of assessed quality - Part 1: Generic specification

DS/EN 129202+A1:1998 空白详细规范：带陶瓷或铁氧体磁芯的线绕电感器-评估等级 P

The document contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with CECC.

Blank detail specification: Wirewound inductors with ceramic or ferrite core - Assessment level P

DS/EN 129102+A1:1998 空白详细规范：评定质量的线绕表面贴装电感器-评定等级 P

The document contains a blank detail specification for wirewound surface mounting inductors for assessed quality, assessment level P.

Blank detail specification: Wirewound surface mounting inductors of assessed quality - Assessment level P

DS/EN 129100+A1:1998 分规范：线绕表面贴装电感器

This specification applies to wire wound fixed rectangular shaped surface mounting (SM) inductors with a magnetic or non-magnetic core for use in electronic equipment. These inductors are intended to be mounted directly onto substrates or boards by their terminations. It presribes preferred ratings and characteristics and selects from CECC 29000 (EN 129000:1993) the appropriate quality assessment procedures and measuring methods and gives general performance requirements for this type of inductor.

Sectional specification: Wirewound surface mounting inductors

DS/EN 129200+A1:1998 分规范：射频电路用铜线绕制陶瓷或铁氧体磁芯固定电感器

This specification applies to fixed inductors for radiofrequency circuits with magnetic or non magnetic core wound with copper wire for use in electronic equipment. It presribes preferred ratings and characteristics and selects from CECC 29000 (EN 129000:1993) the appropriate quality assessment procedures and measuring methods and gives general performance requirements for this type of inductor.

Sectional specification: Fixed inductors with ceramic or ferrite core wound with copper wire for RF circuits