33.060.30;33.060.40;33.160.01 标准查询与下载

IEC 60728-1-1:2014 电视信号, 声音信号和交互服务用电缆网络. 第1-1部分: 双向家庭网络用射频电缆

Cable networks for television signals, sound signals and interactive services - Part 1-1: RF cabling for two way home networks

BS EN 60728-1-1:2010 电视信号,声音信号和交互式服务用电缆网络.双向家用网络用射频(RF)电缆

This part of IEC 60728 provides the requirements and describes the implementation guidelines of RF cabling for two-way home networks; it is applicable to any home network that distributes signals provided by CATV/MATV/SMATV cable networks (including individual receiving systems) having a coaxial cable output. It is also applicable to home networks where some part of the distribution network uses wireless links, for example in place of the receiver cord. This part of IEC 60728 is therefore applicable to RF cabling for two-way home networks with wired cords or wireless links inside a room and primarily intended for television and sound signals operating between about 5 MHz and 3 000 MHz. The frequency range is extended to 6 000 MHz for distribution techniques that replace wired cords with a wireless two-way communication inside a room (or a small number of adjacent rooms) that uses the 5 GHz to 6 GHz band. In a building divided into apartment blocks, the distribution of the signals inside the home starts from the home network interface (HNI) up to the system outlet or terminal input. The requirements at the system outlet are given in IEC 60728-1, Clause 5 and the requirements at the HNI are given in IEC 60728-1, Clause 7. In Clause 5 of this standard additional requirements are given. This standard deals with various possibilities to distribute signals in a home network, using coaxial cables, balanced pair cables, fibre optic cables (glass or plastic) and also wireless links inside a room (or a small number of adjacent rooms) to replace wired cords. This standard gives references to basic methods of measurement of the operational characteristics of the home cable network in order to assess its performance. All requirements refer to the performance limits, which are obtained between the input(s) at the home network interface (HNI) and the output at any system outlet when terminated in a resistance equal to the nominal load impedance of the system, unless otherwise specified. Where system outlets are not used, the above applies to the terminal input. Clause 5 defines the performance limits measured at system outlet or terminal input for an unimpaired (ideal) test signal applied at the HNI. Under normal operating conditions for any analogue channel and meeting these limits, the cumulative effect of the impairment of any single parameter at the HNI and that due to the home network will produce picture and sound signals not worse than Grade four on the five-grade impairment scale contained in ITU-R BT.500. These requirements are given in IEC 60728-1-2. For digitally modulated signals the quality requirement is a QEF (Quasi Error Free) reception. This standard describes the physical layer connection for home networks. Description of protocols required for Layer 2 and higher layers is out of the scope of this standard. Logical connections between devices within the home network are therefore not always guaranteed.

Cable networks for television signals, sound signals and interactive services. RF cabling for two way home networks

IEC 60728-1-1:2010 电视信号、声音信号和交互式服务用电缆网络.第1-1部分:双向家用网络用射频(RF)电缆

This part of IEC 60728 provides the requirements and describes the implementation guidelines of RF cabling for two-way home networks; it is applicable to any home network that distributes signals provided by CATV/MATV/SMATV cable networks (including individual receiving systems) having a coaxial cable output. It is also applicable to home networks where some part of the distribution network uses wireless links@ for example in place of the receiver cord. This part of IEC 60728 is therefore applicable to RF cabling for two-way home networks with wired cords or wireless links inside a room and primarily intended for television and sound signals operating between about 5 MHz and 3 000 MHz. The frequency range is extended to 6 000 MHz for distribution techniques that replace wired cords with a wireless two-way communication inside a room (or a small number of adjacent rooms) that uses the 5 GHz to 6 GHz band. In a building divided into apartment blocks@ the distribution of the signals inside the home starts from the home network interface (HNI) up to the system outlet or terminal input. The requirements at the system outlet are given in IEC 60728-1@ Clause 5 and the requirements at the HNI are given in IEC 60728-1@ Clause 7. In Clause 5 of this standard additional requirements are given. This standard deals with various possibilities to distribute signals in a home network@ using coaxial cables@ balanced pair cables@ fibre optic cables (glass or plastic) and also wireless links inside a room (or a small number of adjacent rooms) to replace wired cords. This standard gives references to basic methods of measurement of the operational characteristics of the home cable network in order to assess its performance. All requirements refer to the performance limits@ which are obtained between the input(s) at the home network interface (HNI) and the output at any system outlet when terminated in a resistance equal to the nominal load impedance of the system@ unless otherwise specified. Where system outlets are not used@ the above applies to the terminal input. NOTE 1 If the home network is subdivided into a number of parts@ using different transmission media (e.g. coaxial cabling@ balanced cabling@ optical cabling@ wireless links) the accumulation of degradations should not exceed the figures given below. NOTE 2 Performance requirements of return paths as well as special methods of measurement for the use of the return paths in cable networks are described in IEC 60728-10. Clause 5 defines the performance limits measured at system outlet or terminal input for an unimpaired (ideal) test signal applied at the HNI. Under normal operating conditions for any analogue channel and meeting these limits@ the cumulative effect of the impairment of any single parameter at the HNI and that due to the home network will produce picture and sound signals not worse than Grade four on the five-grade impairment scale contained in ITU-R BT.500. These requirements are given in IEC 60728-1-2. For digitally modulated signals the quality requirement is a QEF (Quasi Error Free) reception. This standard describes the physical layer connection for home networks. Description of protocols required for Layer 2 and higher layers is out of the scope of this standard. Logical connections between devices within the home network are therefore not always guaranteed.

Cable networks for television signals, sound signals and interactive services - Part 1-1: RF cabling for two way home networks