33.180.20;33.180.30 标准查询与下载

IEC 62343-3-1:2016 动态模块.第3-1部分:性能规范模块.动态通道均衡器

This part of IEC 62343 provides a performance specification template for the dynamic channel equalizer (DCE). The object of this performance specification template is to provide a framework for the preparation of detail specifications on the product or performance of dynamic channel equalizers. Additional specification parameters may be included for product specifications or performance specifications. However, specification parameters specified in this standard should not be removed from the product specifications or performance specifications. Technical information regarding dynamic channel equalizers and their applications in DWDM systems is described in IEC TR 62343-6-1.

Dynamic modules - Part 3-1: Performance specification templates - Dynamic channel equalizers

IEC 62149-2:2014 光纤有源元件及器件的性能标准.第2部分:850 nm离散垂直空穴表面发射激光器件

"This part of IEC 62149 covers the performance specification for 850-nm discrete vertical cavity surface emitting laser (VCSEL) devices of transverse multimode types used for fibre optic telecommunication and optical data transmission applications. The performance standard contains a definition of the product performance requirements together with a series of sets of tests and measurements with clearly defined conditions@ severities@ and pass/fail criteria. The tests are intended to be run on a ""once-off"" basis to prove any product's ability to satisfy the performance standard's requirements. A product that has been shown to meet all the requirements of a performance standard can be declared as complying with the performance standard@ but should then be controlled by a quality assurance/quality conformance program. Depending on the modulation speeds@ sub-categorized specifications are defined. Types A1@ A2@ A3 and A4 correspond to 1@25 Gbit/s@ 2@5 Gbit/s@ 4@25 Gbit/s and 10 Gbit/s VCSELs@ respectively. Each sub-categorized specification is also defined by separate details depending on the device types@ such as specifications for a VCSEL device without a monitor photodiode (case a) and for a VCSEL device with a monitor photodiode (case b)."

Fibre optic active components and devices - Performance standard - Part 2: 850 nm discrete vertical cavity surface emitting laser devices

IEC 62148-15:2014 光纤有源元件及器件.包装和接口标准.第15部分:离散垂直空腔表面发射激光器封装

This part of IEC 62148 covers the physical dimension and interface specifications for the discrete vertical cavity surface emitting laser (VCSEL) devices in optical telecommunication and optical data transmission applications. The intent of this standard is to adequately specify the physical requirements of VCSEL devices that will enable mechanical interchangeability of laser devices or transmitters complying with this standard both at the printed circuit wiring board and for any panelmounting requirement.

Fibre optic active components and devices - Package and interface standards - Part 15: Discrete vertical cavity surface emitting laser packages

IEC 62149-3:2014 纤维光学有源元件和器件. 性能标准. 第3部分: 2,5-Gbit/s至40-Gbit/s纤维光学传输系统用调制器集成激光二极管发射器

This part of IEC 62149 covers the performance specification for optical modulators monolithically integrated with laser diodes for 2@5 Gbit/s to 40 Gbit/s multi-channel fibre optic transmission systems. This performance standard contains a definition of the product performance requirements together with a series of sets of tests and measurements with clearly defined conditions@ severities and pass/fail criteria. The tests are intended to be run as an initial design verification to prove any product's ability to satisfy the performance standard's requirements. This standard is only applicable for on-off keying format. A product that has been shown to meet all the requirements of a performance standard can be declared as complying with the performance standard@ but should then be controlled by a quality assurance program.

Fibre optic active components and devices - Performance standards - Part 3: Modulator-integrated laser diode transmittersfor 2,5-Gbit/s to 40-Gbit/s fibre optic transmission systems

IEC 62149-8:2014 纤维光学有源元件和器件. 性能标准. 第8部分: 晶种反射半导体光放大器设备

"This part of IEC 62149 covers the performance specification for seeded reflective semiconductor optical amplifier (RSOA) devices used for fibre optic telecommunication and optical data transmission applications. The performance standard contains a definition of the product performance requirements together with a series of sets of tests and measurements with clearly defined conditions@ severities@ and pass/fail criteria. The tests are intended to be run on a ""once-off"" basis to prove any product's ability to satisfy the performance standard's requirements. A product that has been shown to meet all the requirements of a performance standard can be declared as complying with the performance standard@ but should then be controlled by a quality assurance/quality conformance program."

Fibre optic active components and devices - Performance standard - Part 8: Seeded reflective semiconductor optical amplifier devices

IEC 62149-9:2014 纤维光学有源元件和器件. 性能标准. 第9部分: 晶种反射半导体光放大器收发器

"This part of IEC 62149 covers the performance specification for seeded reflective semiconductor optical amplifier (RSOA) transceivers used for the fibre optic telecommunication and optical data transmission applications. The performance standard contains a definition of the product performance requirements together with a series of sets of tests and measurements with clearly defined conditions@ severities@ and pass/fail criteria. The tests are intended to be run on a ""once-off"" basis to prove any product's ability to satisfy the performance standard's requirements. A product that has been shown to meet all the requirements of a performance standard can be declared as complying with the performance standard@ but should then be controlled by a quality assurance/quality conformance program."

Fibre optic active components and devices - Performance standards - Part 9: Seeded reflective semiconductor optical amplifier transceivers

IEC 61291-1:2012 光学放大器.第1部分:总规范

"Scope and object This part of IEC 61291 applies to all commercially available optical amplifiers (OAs) and optically amplified assemblies. It applies to OAs using optically pumped fibres (OFAs based either on rare-earth doped fibres or on the Raman effect)@ semiconductors (SOAs)@ and waveguides (POWAs). The object of this standard is: ?C to establish uniform requirements for transmission@ operation@ reliability and environmental properties of OAs; ?C to provide assistance to the purchaser in the selection of consistently high-quality OA products for his particular applications. Parameters specified for OAs are those characterizing the transmission@ operation@ reliability and environmental properties of the OA seen as a ""black box"" from a general point of view. In the sectional and detail specifications a subset of these parameters will be specified according to the type and application of the particular OA device or assembly."

Optical amplifiers - Part 1: Generic specification

IEC 62149-1:2011 纤维光学有源元件和器件.性能标准.第1部分:总则和指南

Fibre optic active components and devices - Performance standards - Part 1: General and guidance

IEC TR 62343-6-6:2011 动态模块.第6-6部分:动态模块的光学单元用故障模式效应分析

This part of IEC 62343, which is a technical report, describes failure mode effect analysis (FMEA) for optical units of dynamic modules. FMEA is one of the effective and useful analysis methods to determine the reliability evaluation test items and conditions which are defined in future reliability qualification documents. In order to estimate the lifetime for a module, there is a typical procedure. The first step is to identify the dominant failure modes. The second step is to determine the acceleration tests according to these failure modes. The third step is to carry out the test. The fourth step is to estimate the acceleration factors. Finally, the fifth step is to calculate the lifetime of the dynamic module. The IEC 61300-2 series defines environment and mechanical tests. This technical report describes the dominant failure mode for dynamic modules and relevant tests from the IEC 61300-2 series.

Dynamic modules - Part 6-6: Failure mode effect analysis for optical units of dynamic modules

BS EN 62149-2:2009 光纤有源组件和设备.性能标准.850 nm离散垂直空腔表面发射激光设备

This part of IEC 62149 covers the performance specification for 850-nm discrete vertical cavity surface emitting laser (VCSEL) devices of transverse multimode types used for the fibre optic telecommunication and optical data transmission application. The performance standard contains a definition of the product performance requirements together with a series of sets of tests and measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are intended to be run on a “once-off” basis to prove any product’s ability to satisfy the performance standard’s requirements. A product that has been shown to meet all the requirements of a performance standard can be declared as complying with the performance standard, but should then be controlled by a quality assurance/quality conformance program. Depending on the modulation speeds, subcategorized specifications are defined. Types A1, A2 and A3 correspond to 1,25 Gbit/s, 2,5 Gbit/s and 4,25 Gbit/s VCSELs, respectively. Each subcategorized specification is also defined by separate details depending on the device types, such as specifications for a VCSEL device without a monitor photodiode (Case a) and for a VCSEL device with a monitor photodiode (Case b).

Fibre optic active components and devices - Performance standards - 850 nm discrete vertical cavity surface emitting laser devices

IEC 62150-4:2009 纤维光学有源元件和器件.试验和测量规程.第4部分:应用时域光学检测系统检测相对强度噪声

This part of IEC 62150 specifies test and measurement procedures for relative intensity noise (RIN). It applies to lasers@ laser transmitters@ and the transmitter portion of transceivers. This procedure examines whether the device or module satisfies the appropriate performance specification. The procedure is applicable to single longitudinal mode (SLM). An optional section of the procedure presents a controlled return loss to the device-under-test@ but is only applicable to devices coupled to SMF. The method described in this standard@ using a time-domain detection system@ provides a single value for RIN that averages the noise over the transmission bandwidth. The measurement is made on a modulated laser capturing the RIN value under normal operating conditions. It also measures RINOMA@ an alternative definition@ as described in IEEE 802.3-2005. An alternative RIN measurement method uses a photoreceiver and electrical spectrum analyzer and provides RIN vs. electrical frequency. This method provides a RIN value averaged over particular electrical band determined by a filter. For a filter bandwidth and characteristic that duplicates the filtering in a transmission system@ this technique provides a result that is appropriate to determine the noise for such a system. This method is based on the measurement of total intensity noise including and does attempt to subtract the effects of thermal and shot noise. Background on laser intensity noise is given in Annex A.

Fibre optic active components and devices - Test and measurement procedures - Part 4: Relative intensity noise using a time-domain optical detection system

IEC 62148-16:2009 光纤有源元件和设备.包装和接口标准.第16部分:与LC连接器接口一同使用的发射器和接收器部件

Fibre optic active components and devices - Package and interface standards - Part 16: Transmitter and receiver components for use with the LC connector interface

IEC 62149-2:2009 光纤有源元件及器件的性能标准.第2部分:850 nm离散垂直空穴表面发射激光器件

Fibre optic active components and devices - Performance standards - Part 2: 850 nm discrete vertical cavity surface emitting laser devices

IEC 62148-11:2009 光纤有源元件及器件.包装和接口标准.第11部分:14针有源器件模块

Fibre optic active components and devices - Package and interface standards - Part 11: 14-pin active device modules