49.025.10 钢 标准查询与下载

BS EN 3525:2023 航空航天系列 钢 15CrMoV6 (1.7334) 空气融化了 经过硬化和回火 盘子 6mm≤a≤20mm 1,080 MPa ≤ Rm ≤ 1,280 MPa

Aerospace series. Steel 15CrMoV6 (1.7334). Air melted. Hardened and tempered. Plates. 6 mm ≤ a ≤ 20 mm. 1 080 MPa ≤ Rm ≤ 1 280 MPa

ASTM A989/A989M-23 高温设备用热等静压合金钢法兰、配件、阀门和零件的标准规范

1.1 This specification covers hot isostatically-pressed, powder metallurgy, alloy steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts made to specified dimensions or to dimensional standards, such as in ASME Specification B16.5. 1.2 Several grades of alloy steels are included in this specification. 1.3 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.4 This specification is expressed in both inch-pound units and in SI units. Unless the order specifies the applicable “M” specification designation (SI units), however, the material shall be furnished to inch-pound units. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.6 The following safety hazards caveat pertains only to test methods portions, 8.1, 8.2, and 9.5 – 9.7 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Hot Isostatically-Pressed Alloy Steel Flanges, Fittings, Valves, and Parts for High Temperature Service

BS EN 2003-2:2023 航空航天系列 钢 测试方法-悬臂梁冲击试验

1   Scope This document specifies the Izod impact test method for steel products used for aerospace applications. It shall be applied when referred to in the EN technical specification or material standard unless otherwise specified on the drawing, order or inspection schedule.

Aerospace series. Steels. Test methods - Izod impact test

BS EN 4628:2022 航空航天系列 钢 X4CrNiMo16-5-1(1.4418)空气融化了 经过硬化和回火 酒吧 从≤200mm 1150MPa≤Rm≤1300MPa

1   Scope This document specifies the requirements relating to: Steel X4CrNiMo16-5-1 (1.4418) Air melted Hardened and tempered Bars D e  ≤ 200 mm 1 150 MPa ≤  R m  ≤ 1 300 MPa for aerospace applications. NOTE Other common designations: — AIR: Z 8 CND 17-04. — Only the chemical composition according to this document is considered.

Aerospace series. Steel X4CrNiMo16-5-1 (1.4418). Air melted. Hardened and tempered. Bars. De ≤ 200 mm. 1 150 MPa ≤ Rm ≤ 1 300 MPa

BS EN 4884:2022 航空航天系列 钢 X3CrNiMoAl（1.4534）真空感应熔化和自耗电极重熔 固溶处理和沉淀处理 机加工用棒材 a或D≤200毫米 1200MPa ≤ Rm ≤ 1350MPa

This document specifies the requirements relating to: Steel X3CrNiMoAl (1.4534) Vacuum induction melted and consumable electrode remelted Solution treated and precipitation treated Bars for machining a or D ≤ 200 mm for aerospace applications.

Aerospace series. Steel X3CrNiMoAl (1.4534). Vacuum induction melted and consumable electrode remelted. Solution treated and precipitation treated. Bars for machining. a or D ≤ 200 mm. 1 200 MPa ≤ Rm ≤ 1 350 MPa

BS EN 3479:2022 航空航天系列 钢 X5CrNiCu15-5（1.4545）自耗电极重熔 固溶处理和沉淀处理 盘子 6毫米＜ A ？ 20 毫米 1070兆帕？ R M ？ 1220兆帕

1   Scope This document specifies the requirements relating to: Steel X5CrNiCu15-5 (1.4545) Consumable electrode remelted Solution treated and precipitation treated Plates 6 mm <  a ≤ 20 mm 1 070 MPa ≤ R m ≤ 1 220 MPa for aerospace applications.

Aerospace series. Steel X5CrNiCu15-5 (1.4545). Consumable electrode remelted. Solution treated and precipitation treated. Plates. 6 mm < a ? 20 mm. 1 070 MPa ? Rm ? 1 220 MPa

BS EN 4883:2022 航空航天系列 钢 X5CrNiCu 17-4（1.4542）空气融化了 固溶处理和沉淀处理 盘子 6毫米≤a≤100毫米 Rm≥1070MPa

This document specifies the requirements relating to: Steel X5CrNiCu 17-4 (1.4542) Air melted Solution treated and precipitation treated Plates 6 mm ≤ a ≤ 100 mm Rm ≥ 1 070 MPa for aerospace applications.

Aerospace series. Steel X5CrNiCu 17-4 (1.4542). Air melted. Solution treated and precipitation treated. Plates. 6 mm ≤ a ≤ 100 mm. Rm ≥ 1 070 MPa

BS EN 3364:2022 航空航天系列 钢 X5CrNiCu15-5(1.4545)自耗电极重熔、软化 锻造库存 a或D≤300毫米

1   Scope This document specifies the requirements relating to: Steel X5CrNiCu15-5 (1.4545) Consumable electrode remelted, softened Forging stock a or D ≤ 300 mm for aerospace applications.

Aerospace series. Steel X5CrNiCu15-5 (1.4545). Consumable electrode remelted, softened. Forging stocks. a or D ≤ 300 mm

BS EN 4627:2022 航空航天系列 钢 X4CrNiMo16-5-1(1.4418)空气融化了 经过硬化和回火 锻件 De≤200毫米 1150 MPa ≤ Rm ≤ 1300 MPa

1   Scope This document specifies the requirements relating to: Steel X4CrNiMo16-5-1 (1.4418) Air melted Hardened and tempered Forgings D e  ≤ 200 mm 1 150 MPa ≤  R m  ≤ 1 300 MPa for aerospace applications. NOTE Other common designations: — AIR: Z 8 CND 17-04. — Only the chemical composition according to this document is considered.

Aerospace series. Steel X4CrNiMo16-5-1 (1.4418). Air melted. Hardened and tempered. Forgings. De ≤ 200 mm. 1 150 MPa ≤ Rm ≤ 1 300 MPa

BS EN 4904:2022 航空航天系列 钢 36NiCrMo16（1.6773）1000MPa ≤ Rm ≤ 1200MPa 酒吧 100毫米≤D≤250毫米

This document specifies the requirements relating to: Steel 36NiCrMo16 (1.6773) Bars for aerospace applications.

Aerospace series. Steel 36NiCrMo16 (1.6773). 1 000 MPa ≤ Rm ≤ 1 200 MPa. Bars. 100 mm ≤ D ≤ 250 mm

BS EN 4882:2022 航空航天系列 钢 X5CrNiCu 17-4（1.4542）空气融化了 固溶处理和沉淀处理 板材和带材 A ？ 6 毫米 R M ？ 1070兆帕

This document specifies the requirements relating to: Steel X5CrNiCu 17-4 (1.4542) Air melted Solution treated and precipitation treated Sheets and strips a ≤ 6 mm Rm ≥ 1 070 MPa for aerospace applications.

Aerospace series. Steel X5CrNiCu 17-4 (1.4542). Air melted. Solution treated and precipitation treated. Sheets and strips. a ? 6 mm. Rm ? 1 070 MPa

BS EN 2573:2022 航空航天系列 钢 X6CrNiTi18-10（1.4541）空气融化了 软化了 电线 0.25 毫米 ≤ De ≤ 3 毫米 Rm≤780兆帕

1   Scope This document specifies the requirements relating to: Steel X6CrNiTi18–10 (1.4541) Air melted Softened Wires 0,25 mm ≤  D e  ≤ 3 mm R m  ≤ 780 MPa for aerospace applications. Material number: 1.4541. ASD-STAN designation: FE-PA3601.

Aerospace series. Steel X6CrNiTi18-10 (1.4541). Air melted. Softened. Wires. 0,25 mm ≤ De ≤ 3 mm. Rm ≤ 780 MPa

ASTM A646/A646M-17(2022) 航空航天用优质钢和合金坯料的标准规范

1.1 This specification covers premium quality alloy steel semifinished rolled or forged blooms and billets for reforging into critical parts such as aircraft landing-gear forgings. 1.2 Blooms and billets, hereinafter referred to as blooms, are semifinished steel products, hot rolled or forged to approximate cross-sectional dimensions. Blooms may be square, round, hexagonal, octagonal, or rectangular in section. For the purposes of this specification, minimum bloom section size will be 16 in.2 [103 cm2 ]. 1.3 This specification covers two basic classifications of steel: 1.3.1 Class I—Vacuum-induction melted or consumableelectrode vacuum melted, or other suitable processes which will satisfy the quality requirements of this specification. 1.3.2 Class II—Air-melted vacuum degassed. 1.3.3 Class III—Air melted electric furnace ladle refined and vacuum degassed. 1.4 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standard. Within the text and tables, the SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 Unless the order specifies the applicable “M” specification the material shall be furnished to the inch-pound units. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Premium Quality Alloy Steel Blooms and Billets for Aircraft and Aerospace Forgings

PN-EN 4825-2021-10 E 航空航天系列 - 钢 X12CrNiMoV12-3（1.4938）- 空气熔炼和自耗电极重熔 - 调质 - 棒材 - De ≤150 mm - 900 MPa ≤Rm ≤1 100 MPa

Aerospace series -- Steel X12CrNiMoV12-3 (1.4938) -- Air melted and consumable electrode remelted -- Hardened and tempered -- Bars -- De ≤ 150 mm -- 900 MPa ≤ Rm ≤ 1 100 MPa

PN-EN 4700-002-2021-10 E 航空航天系列 钢和耐热合金 锻造产品 技术规范 第002部分：棒材和型材

Aerospace series -- Steel and heat resisting alloys -- Wrought products -- Technical specification -- Part 002: Bars and sections

OENORM EN 3361-2021 航空航天系列 钢 X5CrNiCu15-5（1.4545） 自耗电极重熔 固溶处理和沉淀处理 板材和带材 a <= 6mm 1070 MPa <= Rm <= 1220 MPa

Aerospace series - Steel X5CrNiCu15-5 (1.4545) - Consumable electrode remelted - Solution treated and precipitation treated - Sheets and strips - a <= 6mm - 1070 MPa <= Rm <= 1220 MPa

OENORM EN 4904-2021 航空航天系列 钢 36NiCrMo16 1000 MPa <= Rm <= 1200 MPa 棒材 100 <= D <= 250 mm

Aerospace series - Steel 36NiCrMo16 - 1000 MPa <= Rm <= 1200 MPa - Bars - 100 <= D <= 250 mm

OENORM EN 3364-2021 航空航天系列 钢 X5CrNiCu15-5（1.4545） 自耗电极重熔、软化 锻坯 a 或 D <= 300 mm

Aerospace series - Steel X5CrNiCu15-5 (1.4545) - Consumable electrode remelted, softened - Forging stocks - a or D <= 300 mm

OENORM EN 4825-2021 航空航天系列 钢 X12CrNiMoV12-3（1.4938） 空气熔炼和自耗电极重熔 淬火和回火 棒材 De ≤150 mm 900 MPa ≤Rm ≤1100 MPa

Aerospace series - Steel X12CrNiMoV12-3 (1.4938) - Air melted and consumable electrode remelted - Hardened and tempered - Bars - De ≤ 150 mm - 900 MPa ≤ Rm ≤ 1100 MPa

21/30442582 DC BS EN 3361 航空航天系列 钢 X5CrNiCu15 5 (1.4545) 自耗电极重熔 固溶处理和沉淀处理 板材和带材 a≤6mm 1 070 MPa ≤ Rm ≤ 1 220 MPa

BS EN 3361. Aerospace series. Steel X5CrNiCu15 5 (1.4545). Consumable electrode remelted. Solution treated and precipitation treated. Sheets and strips. a ≤ 6mm. 1 070 MPa ≤ Rm ≤ 1 220 MPa