59.060.30 矿物纤维和金属纤维 标准查询与下载

GB/T 6646.1-1986 温石棉纤维干式分级方法

本标准适用于机选石棉纤维商业等级的划分。

Method for dry classification of chrysotile asbestos fibre

GB/T 6646.2-1986 温石棉纤维长度湿式分级方法

本标准适用于机选温石棉纤维长度分布和-200目粉尘含量的测定。

Method for wet classification of chrysotile asbestos fibre by length distribution

GB/T 6646.3-1986 温石棉纤维长度快速湿式分级方法

本标准适用于机选3～6级温石棉纤维长度分布和-200目粉尘含量的测定。

Method for rapid wet classification of chrysotile asbestos fibre by length distribution

GB/T 6646.4-1986 温石棉比表面积测定方法

本标准适用于机选石棉比表面积的测定，测量范围为20～400dm2/g。

Method for specific surface area of chrysotile asbestos

GB/T 6646.5-1986 温石棉中砂粒与未解离石棉含量测定方法

本标准适用于机选3～6级温石棉中砂粒与未解离石棉含量的测定。

Method for determination of grit and crude content in chrysotile asbestos

GB/T 6646.6-1986 温石棉水分测定方法

本标准适用于温石棉中水分的测定。有两种方法可选择，一种是水分仪法；另一种是干燥箱法。

Test method for moisture content of chrysotile asbestos

T/CFIA P6-2023 玄武岩纤维直接纱

主要技术内容包括： 分类和代号 外观 氧化铁含量 纤维直径 线密度 含水率 可燃物含量 力学性能 耐候性 耐碱盐性能 耐温性能 硬挺度 短切率、分散率

Basalt fiber direct yarn

T/CFIA P5-2023 玻璃纤维开刀丝

本标准包括条款9章。 条款包括：范围、规范性引用文件、术语和定义、分类和代号、要求、试验方法、检验规则、标志和包装、运输和贮存。 玻璃纤维开刀丝代号包括以下要素： a）表示玻璃纤维开刀丝的英文字母GC； b）玻璃类型，E表示无碱玻璃、C表示中碱玻璃，其它玻璃种类参照GB/T 4202执行； c）表示开刀丝形态的英文字母，团状为B、条状为S、混杂状为M； d）表示开刀丝等级的拉丁数字编号。 示例1.I级团状无碱玻璃纤维开刀丝表示为：GC-EB-I 示例2：III级混杂状中碱玻璃纤维开刀丝表示为：GC-CM-III 技术要求方面： 1）外观质量：色泽应均匀，不团聚，不应有影响使用的污渍、霉斑等。 2）玻璃成分：按GB/T 18369执行。 3）含水率和含杂率按照标准相关指标确定评级。

Glass fiber cutting thread

T/CFIA P2-2022 本体彩色连续玻璃纤维纱

本文件规定了本体彩色连续玻璃纤维纱的产品代号、要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于通过本体着色纤维玻璃拉制的本体彩色连续玻璃纤维纱。

Noumenon colored continuous glass fiber yarn

ASTM E2016-22 工业用编织金属丝布的标准规范

1.1 This specification covers industrial woven wire fabric, referred to as wire cloth, for general use including the separation of particles. Wire cloth can be made of any primary metal or metal alloy wire that is suitable for weaving. This specification does not apply to the following special types of wire cloth: filter cloth or dutch weave (see Appendix X1), fourdrinier and cylinder cloth, galvanized hardware cloth, insect wire screening, spiral weave wire cloth, testing sieve cloth, or welded wire cloth. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Industrial Woven Wire Cloth

ASTM E2016-20 工业编织线布标准规格

Standard Specification for Industrial Woven Wire Cloth

T/ZZB 0749-2018 双面同花数码喷墨印花桑蚕丝围巾

本标准规定了双面同花数码喷墨印花桑蚕丝围巾的术语和定义、规格标示、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺等。 本标准适用于桑蚕长丝含量为100%的双面同花数码喷墨印花围巾产品，不适用于14 岁及以下的儿童和婴幼儿产品。

Double-side digital ink jet printing mulberry silk scarves

DIN SPEC 25714:2017-09 玄武岩纤维 技术规范

This DIN SPEC in accordance with the PAS procedure was developed within a workshop set up on a temporary basis. The document was developed and approved by authors named in the foreword. This DIN SPEC specifies a designation system, test criteria, test methods and requirements for the marking, packaging and storage of rovings that are produced from molten basalt in a (thermal) melt-spinning process and that are used in the production of textiles as reinforcing fibres for use with plastics, hydraulic dies or in other applications. Textured yarns, yarns from staple fibres and pre-impregnated rovings are not covered in this DIN SPEC.

Basalt fibers - Technical specification; Text in German and English

KS K 0304-2015 石棉的鉴别法

Identification of asbestos

KS K 0321-2014 铜氨人造丝的鉴定

Identification of cuprammonium rayon

ASTM D1573/D1573M-95(2009)e1 石棉纺织品热老化的标准试验方法

Standard Test Method for Heat Aging of Asbestos Textiles

ABNT NBR 14025-2008 非织造布 - 抗水渗透的测定 - 静水压试验

This standard pescribes the method for determination of the resistance of nonwovens, with or without repellent finishings, to the penetration of water when submitted to the hydrostatic pressure.

Nonwoven - Determination of resistance to water penetration - Hydrostatic pressure test

ANSI/ASTM E2016:1999 工业纺织金属丝布规范

This practice is intended to measure and evaluate fenestration assemblies and impact protection systems for resistance to impact energies under specified conditions. Window and dooor assemblies covered by this practice also include individual components such as the glazing in-fill. This practice is a standard procedure for determining the ability of glazed panels, fenestration assemblies, fenestration components and impact protection systems to resist applied impact energies. Warning: This standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Specification for Industrial Woven Wire Cloth

CNS 4891-1996 聚丙烯月青棉状纤维（收缩型）

本标准适用于放缩型聚丙烯晴棉状纤维。

Polyacrylonitrile Staple Fibers (Shrinkable Type)

ASTM D628/D628M-95(2009)e1 石棉套管的标准规范

1.1 This specification covers woven and braided asbestos tubular sleeving having a minimum of 75 mass % of asbestos fiber, excluding the mass of other inorganic strands which may be present. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 Warning—Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysoltile asbestos, refer to “Safe Use of Chrysotile Asbestos: A Manual on Preventive and Control Measures.” 1.4 The following safety hazards caveat pertains only to the test methods, Section 13, described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific safety hazard, see 1.3.

Standard Specification for Asbestos Tubular Sleeving