590 标准查询与下载

DS 2168:1991 轮胎翻新

Formålet med denne standard er at sikre, at der ved fremstil-lingen af regummierede dæk efter standarden anvendes ma-terialer og processer af en høj kvalitet med henblik på at opnå tilfredsstillende egenskaber, herunder rundhed, balance, slid-styrke og sikkerhed. Standarden fastlægger minimumskrav til fremstillingen af regummierede dæk, herunder regummieringsvirksomheder-nes maskinpark, samt inspektioner og prøvninger til kvali-tetskontrol af produktionen. Standarden omfatter personbildæk, varebildæk (C-dæk) samt lastbildæk.

Retreading of tyres for automobiles

DS/ISO 6310:1988 道路车辆.制动闸衬.压缩性.试验程序

This International Standard specifies a method for testing and measuring the compressibility of brake linings.

Road vehicles. Brake linings. Compressibility. Test procedure

DS/ISO 7629:1988 道路车辆.制动闸衬.园形制动垫片.试验后表面和材料伤残的评定

This International Standard identifies the types of flaws of surface and material after testing of disc brake pads, and specifies the method of measuring these flaws and of setting out the results. This International Standard applies to disc brake pads intended for fitting to the brakes of road vehicles.

Road vehicles. Brake linings. Disc brake pads. Evaluation of surface and material flaws after testing

DS/ISO 5676:1986 农业和林业拖拉机和机械.液压管接头.制动回路

Denne internationale standard gælder kun for hydrauliske bremsekoblinger. Bremsesystemet er regulerbart og fungerer ved trykforøgelse inden for et arbejdsområde mellem 10 og 15MPa(100og 150 bar). Disse koblinger bruges til at tilslutte eller afbryde bremsesystemet, når bugserede landbrugs- eller skovbrugsmaskiner til- eller frakobles.

Tractors and machinery for agriculture and forestry. Hydraulic coupling. Braking circuit

DS/ISO 6815:1986 林业机械. 悬挂装置. 尺寸

This International Standard lays down the essential dimensions of two types of hitches on self-propelled forestry machinery for the attachment of towed implements f itted with drawbars having ring type hitches. Outline requirements for those drawbars, which are necessary to ensure compatibility, are also specified.

Machinery for forestry. Hitches. Dimensions

DS/ISO 5696:1986 牵引式农业车辆. 制动和制动装置. 实验室试验方法

This International Standard specifies a method of bench testing of brakes and their control devices in order to determine their suitability for use on trailed agricultural vehicles.

Trailed agricultural vehicles. Brakes and braking devices. Laboratory test method

DS/EN 23164:1986 土方机械．翻车和落物保护结构的试验室评估；偏转限制量规范

Earth-moving machinery. Laboratory evaluations of roll-over and falling-object protective structures. Specifications for the deflection-limiting volume

DS/ISO 5353:1986 土方机械. 驾驶座标定点

This International Standard specifies a method and a device for use in establishing the position of the seat index point for any kind of padded seat.

Earth-moving machinery and tractors and machinery for agriculture and forestry. Seat index point

DS/ISO 8759/2:1986 农业轮式拖拉机. 前端装配的悬挂装置和功率输出轴. 第2部分: 前端悬挂装置

Denne del af DS/ISO 8759 fastl?gger krav til det l?ftebare trepunktsoph?ng, der bruges til frontmontering af redskaber eller udstyr p? landbrugstraktorer Standarden g?lder for traktorer af de kategorier, der er defineret i DS/ISO 730/1 Note - DS/ISO 8759/1, fastl?gger krav til front-kraftudtag (PTO).

Agricultural wheeled tractors. Front-mounted linkage and power take-off. Part 2: Front linkage

DS/ISO 5700:1985 农业和林业轮式拖拉机. 保护结构. 稳态试验方法和验收条件

This International Standard specifies a static loading test method and the acceptance conditions for protective structures (cab or frame) of agricultural and forestry wheeled tractors.

Agricultural and forestry wheeled tractors. Protective structures. Static test method and acceptance conditions

DS/ISO 3463:1985 农业和林业轮式拖拉机.防护结构.动力试验方法和验收条件

This International Standard specifies a dynamic test method and the acceptance conditions for protective structures (cab or frame) of agricultural and forestry wheeled tractors.

Agricultural and forestry wheeled tractors. Protective structures. Dynamic test method and acceptance conditions

DS/ISO 789/5:1984 农业拖拉机.试验程序.第5部分:动力输出端(PTO).非机械传输功率

This part of ISO 789 specifies test procedures for determining the power available for power take-off systems on agricultural tractors, of the wheeled, track laying or semi-track laying type, in which power transmission is accomplished by means other than a direct mechanical coupling between the engine and the PTO output shaft. NOTE — For drawbar performance tests, see ISO 789/1. For specifica-tions, see ISO 500.

Agricultural tractors. Test procedures. Part 5: Partial power PTO. Non-mechanically transmitted power

DS 2044:1984 汽车和商业机动车辆内外胎的修理

Denne standard specificerer de minimumkrav, der stilles til ydeevne, inspektion, m?rkning og materi-alestyrke for permanente reparationer, der foretages p? bild?k og -slanger. Standarden definerer sikkerhedsd?k, men reparation af disse er ikke omfattet af standarden; fabri-kanten b?r konsulteres vedr?rende reparation. Bem?rk: Det understreges, at kun permanente reparationer kan opfattes som v?rende i overens-stemmelse med denne standard. Det er et krav, at d?kket tages af f?lgen for inspektion (se 5.1), og at reparationer af skader, der g?r gennem d?kkets karkasse, foretages med en egnet reparation p? indersiden af d?kket (se 6.2).

Repairs to tyres and tubes for cars and commercial motor vehicles

DS/ISO 5675:1983 农业拖拉机和机械.一般用途液压管接头.规范

Denne standard g?lder for koblinger til hydrauliske forbindelser, der ofte skal til- eller frakobles, for at landbrugsmaskiner kan skiftes fra traktor til traktor. Standarden omfatter ikke hydrauliske bremsesy-stemer.

Agricultural tractors. Hydraulic couplers for general purpose. Specifications

DS/ISO 789/4:1983 农业拖拉机.试验程序.第4部分:排烟测量

This part of ISO 789 specifies a method of measuring the smoke emitted by the engines of agricultural tractors operating at a steady speed.

Agricultural tractors. Test procedures. Part 4: Measurement of exhaust smoke

DS/ISO 789/6:1983 农业拖拉机.试验程序.第6部分:重心

This part of ISO 789 specifies a method of determining the position of the centre of gravity of agricultural tractors. The method is applicable to agricultural tractors having at least two axles fitted with wheels or tracks.

Agricultural tractors. Test procedures. Part 6: Centre of gravity

DS/ISO 789/2:1983 农业拖拉机.试验程序.第2部分:液压功率和提升能力

This part of ISO 789 specifies test procedures for determining the following hydraulic performance characteristics of agricultural tractors: a) the maximum vertical force which can be exerted by the hydraulic lift at the lower hitch points throughout their full range of movement; b) the maximum vertical force which can be exerted by the hydraulic lift, at a point 610 mm to the rear of the hitch points on a frame attached to the three-point linkage, throughout its full range of movement; c) the maximum hydraulic power available at an external hydraulic tapping; d) optionally, the ability of the lifting system to maintain the load in the lifted position without hydraulic power. NOTE — To ensure that the lifting capacity and the hydraulic power are adequate for effective practical use and also to allow for variation in the performance of nominally identical tractors, the measured maxi-mum performance is reported as that which would be obtained with the hydraulic fluid pressure maintained at 90 % of the pressure sus-tained by the relief valve (see 5.1.3.4).

Agricultural tractors. Test procedures. Part 2: Hydraulic power and lifting capacity

DS/ISO 789/3:1983 农业拖拉机.试验程序.第3部分:转弯直径和出清直径

This part of ISO 789 specifies a method of determining the turning and clearance diameters of agricultural tractors. The method is applicable to agricultural tractors having at least two axles fitted with pneumatic tyres or tracks.

Agricultural tractors. Test procedures. Part 3: Turning and clearance diameters

DS/ISO 3449:1982 土方机械. 下落物体防护结构. 实验室试验和性能要求

Denne standard g?lder for f?lgende f?rerbetjente maskintyper, uanset typen af det anvendte styresystem som defineret i ISO 6165: - b?ltel?ssere og gummihjulsl?ssere - b?ltetraktorer og gummihjulstraktorer - gradere - traktor-planeringsmaskiner

Earth-moving machinery. Falling-object protective structures. Laboratory tests and performance requirements

DS/ISO 3471:1982 土方机械. 防倾翻结构. 实验室试验和性能要求. 第1部分: 履带式和轮式装载机和拖拉机, 反铲式装载机, 平地机, 牵引式铲运机和绞接式翻斗车

1 Denne standard g?lder for f?lgende f?rerbetjente maskintyper, uanset typen af det anvendte styresystem som defineret i ISO 6165: - b?ltel?ssere og gummihjulsl?ssere - b?ltetraktorer og gummihjulstraktorer - gradere - traktor-planeringsmaskiner 2 Denne standard omfatter ikke: - kompaktorer - maskiner med en nominel ydelse p? mindre end 1 5 kW (20 hk) - gravemaskiner - sl?beskovlsmaskiner

Earth-moving machinery. Roll-over protective structures. Laboratory tests and performance requirements