75.180.20 加工设备 标准查询与下载
共找到 270 条与 加工设备 相关的标准，共 18 页
Lubrication, shaft sealing and oil control systems and auxiliary equipment for the petroleum, heavy chemical and natural gas industries - Part 1: General requirements
- ICS
- 75.180.20
- CCS
- J72
- 发布
- 2023-05-23
- 实施
- 2023-12-01
Lubrication, shaft sealing and control oil systems and auxiliary equipment for the petroleum, heavy chemical and natural gas industries - Part 3: Oil systems for general purposes
- ICS
- 75.180.20
- CCS
- J72
- 发布
- 2023-05-23
- 实施
- 2023-12-01
BS EN ISO 18796-2 Oil and gas industries including lower carbon energy – Internal coating of carbon steel process vessels - Part 2: Guideline for selection of coating systems
- ICS
- 75.180.20
- CCS
- 发布
- 2024-02-21
- 实施
- 2024-02-21
1.1 This test method covers a procedure for determination of the distillation characteristics of petroleum products and liquid fuels having boiling range between 20 °C to 400 °C at atmospheric pressure using an automatic micro distillation apparatus. 1.2 This test method is applicable to such products as; light and middle distillates, automotive spark-ignition engine fuels, automotive spark-ignition engine fuels containing up to 20 % ethanol, aviation gasolines, aviation turbine fuels, regular and low sulfur diesel fuels, biodiesel (B100), biodiesel blends up to 20 % biodiesel, special petroleum spirits, naphthas, white spirits, kerosines, burner fuels, and marine fuels. 1.3 The test method is also applicable to hydrocarbons with a narrow boiling range, like organic solvents or oxygenated compounds. 1.4 The test method is designed for the analysis of distillate products; it is not applicable to products containing appreciable quantities of residual material. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Micro Distillation Method)
- ICS
- 75.180.20
- CCS
- 发布
- 2024-01-25
- 实施
Oil and gas industries including lower carbon energy. Flare details for general refinery and petrochemical service
- ICS
- 75.180.20
- CCS
- 发布
- 2023-10-31
- 实施
- 2023-10-31
Oil and gas industries including lower carbon energy – Internal coating of carbon steel process vessels — Part 2: Guideline for selection of coating systems
- ICS
- 75.180.20
- CCS
- 发布
- 2023-10
- 实施
Oil and gas industries including lower carbon energy — Flare details for general refinery and petrochemical service
- ICS
- 75.180.20
- CCS
- 发布
- 2023-10
- 实施
- 2023-10
This document is applicable to dry gas sealing systems for axial, centrifugal, and rotary screw compressors and expanders as described in ISO 10439 (all parts), ISO 10440-1 and ISO 10440-2. Although intended for use primarily in oil refineries, it is also applicable to petrochemical facilities, gas plants, liquefied natural gas (LNG) facilities and oil and gas production facilities. The information provided is designed to aid in the selection of the system that is most appropriate for the risks and circumstances involved in various installations. This document does not apply to other types of shaft seals such as clearance seals, restrictive ring seals or oil seals. This document is a supplement to API Std 692, 1st edition (2018), the requirements of which are applicable with the exceptions specified in this document.
Petroleum, petrochemical and natural gas industries — Dry gas sealing systems for axial, centrifugal, and rotary screw compressors and expanders
- ICS
- 75.180.20
- CCS
- 发布
- 2023-09-10
- 实施
1 Scope This document specifies the requirements for the procedures and design criteria used for calculating the required wall thickness of new tubes and associated component fittings for petroleum, petrochemical and natural gas industries. These procedures are appropriate for designing tubes for service in both corrosive and non-corrosive applications. These procedures have been developed specifically for the design of refinery and related process-fired heater tubes (direct-fired, heat-absorbing tubes within enclosures). These procedures are not intended to be used for the design of external piping. This document does not give recommendations for tube retirement thickness. A technique for estimating the life remaining for a heater tube is described This document is a supplement to API 530, 7th edition (2015) including addendum 1 and addendum 2, the requirements of which are applicable with the exceptions specified in this document.
Petroleum, petrochemical and natural gas industries. Calculation of heater-tube thickness in petroleum refineries
- ICS
- 75.180.20
- CCS
- 发布
- 2022-11-30
- 实施
- 2022-11-30
This document specifies the requirements for the procedures and design criteria used for calculating the required wall thickness of new tubes and associated component fittings for petroleum, petrochemical and natural gas industries. These procedures are appropriate for designing tubes for service in both corrosive and non-corrosive applications. These procedures have been developed specifically for the design of refinery and related process-fired heater tubes (direct-fired, heat-absorbing tubes within enclosures). These procedures are not intended to be used for the design of external piping. This document does not give recommendations for tube retirement thickness. A technique for estimating the life remaining for a heater tube is described This document is a supplement to API 530, 7th edition (2015) including addendum 1 and addendum 2, the requirements of which are applicable with the exceptions specified in this document.
Petroleum, petrochemical and natural gas industries - Calculation of heater-tube thickness in petroleum refineries (ISO 13704:2022)
- ICS
- 75.180.20
- CCS
- 发布
- 2022-11-16
- 实施
- 2023-02-28
This documentspecifies the requirements for the procedures and design criteria used forcalculatingthe required wall thickness of new tubes and associated component fittings for petroleum, petrochemical and natural gas industries. These procedures are appropriate for designing tubes for service in both corrosive and non-corrosive applications. These procedures have been developed specifically for the design of refinery and related process-fired heater tubes (direct-fired, heat-absorbing tubes within enclosures). These procedures are not intended to be used for the design of external piping. This document does not give recommendations for tube retirement thickness. A technique for estimating the life remaining for a heater tube is described This document is a supplement to API 530, 7th edition (2015) including addendum 1 and addendum 2, the requirements of which are applicable with the exceptions specified in this document.
Petroleum, petrochemical and natural gas industries — Calculation of heater-tube thickness in petroleum refineries
- ICS
- 75.180.20
- CCS
- 发布
- 2022-10-24
- 实施
本文件规定了过氧化氢生产用聚结分离器（以下简称“分离器”）的分类和命名、要求、检验规则、标志、出厂文件、包装及运输。 本文件适用于过氧化氢生产用的聚结分离器。
Coalescence separator for hydrogen peroxide production
- ICS
- 75.180.20
- CCS
- C352
- 发布
- 2022-06-22
- 实施
- 2022-06-29
Petroleum, petrochemical and natural gas industries. Dry gas sealing systems for axial, centrifugal, and rotary screw compressors and expanders
- ICS
- 75.180.20
- CCS
- 发布
- 2021-12-31
- 实施
- 2021-12-31
This document is applicable to dry gas sealing systems for axial, centrifugal, and rotary screw compressors and expanders as described in ISO 10439 (all parts), ISO 10440-1 and ISO 10440-2. Although intended for use primarily in oil refineries, it is also applicable to petrochemical facilities, gas plants, liquefied natural gas (LNG) facilities and oil and gas production facilities. The information provided is designed to aid in the selection of the system that is most appropriate for the risks and circumstances involved in various installations. This document does not apply to other types of shaft seals such as clearance seals, restrictive ring seals or oil seals. This document is a supplement to API Std 692, 1st edition (2018), the requirements of which are applicable with the exceptions specified in this document.
Petroleum, petrochemical and natural gas industries - Dry gas sealing systems for axial, centrifugal, and rotary screw compressors and expanders (ISO 6368:2021)
- ICS
- 75.180.20
- CCS
- 发布
- 2021-12-01
- 实施
- 2022-03-31
This document is applicable to dry gas sealing systems for axial, centrifugal, and rotary screw compressors and expanders as described in ISO 10439 (all parts), ISO 10440-1 and ISO 10440-2. Although intended for use primarily in oil refineries, it is also applicable to petrochemical facilities, gas plants, liquefied natural gas (LNG) facilities and oil and gas production facilities. The information provided is designed to aid in the selection of the system that is most appropriate for the risks and circumstances involved in various installations. This document does not apply to other types of shaft seals such as clearance seals, restrictive ring seals or oil seals. This document is a supplement to API Std 692, 1st edition (2018), the requirements of which are applicable with the exceptions specified in this document.
Petroleum, petrochemical and natural gas industries — Dry gas sealing systems for axial, centrifugal, and rotary screw compressors and expanders
- ICS
- 75.180.20
- CCS
- 发布
- 2021-11-18
- 实施
本文件规定了生物柴油产品的储存和运输操作规范。 本文件适用于生物柴油产品的储存和运输。 本文件不适用于生产原料以及BD100生物柴油与石油柴油调和后的产品。
Biodiesel storage and transportation operating specifications
- ICS
- 75.180.20
- CCS
- F13
- 发布
- 2021-11-16
- 实施
- 2022-02-16
Petroleum, petrochemicals and natural gas industries - Internal coating and lining of carbon steel process vessels - Part 1: Technical requirements
- ICS
- 75.180.20
- CCS
- 发布
- 2021-09-09
- 实施
- 2021-09-09
This document specifies the minimum technical requirements for surface preparation, materials, application, inspection and testing of internal coating and lining systems that are intended to be applied on internal surfaces of process vessels that are subject to marked pressure/temperature changes and/or potentially corrosive conditions or processes and aggressive chemicals, used in the oil and gas industry. This document covers both new construction and maintenance works of process vessels as well as the repair of defective and deteriorated coating and lining systems. This document also provides the minimum requirements for the coated and lined samples and the criteria for their approval.
Petroleum, petrochemicals and natural gas industries — Internal coating and lining of carbon steel process vessels — Part 1: Technical requirements
- ICS
- 75.180.20
- CCS
- 发布
- 2021-07-01
- 实施
This document specifies requirements and gives recommendations for the mechanical design, material selection, fabrication, inspection, testing and preparation for shipment of shell-and-tube heat exchangers for the petroleum, petrochemical and natural gas industries. This document supplements API Std 660, 9th edition (2015), the requirements of which are applicable with the exceptions specified in this document. This document is applicable to the following types of shell-and-tube heat exchangers: heaters, condensers, coolers and reboilers. This document is not applicable to vacuum-operated steam surface condensers and feed-water heaters.
Petroleum, petrochemical and natural gas industries — Shell-and-tube heat exchangers
- ICS
- 75.180.20
- CCS
- 发布
- 2021-07-01
- 实施
This document is applicable to pressure-relieving and vapour depressuring systems. Although intended for use primarily in oil refineries, it is also applicable to petrochemical facilities, gas plants, Liquefied Natural Gas (LNG) facilities and oil and gas production facilities. The information provided is designed to aid in the selection of the system that is most appropriate for the risks and circumstances involved in various installations. This document supplements API Std 521, 6th edition (2014), the requirements of which are applicable with the exceptions specified in this document.
Petroleum, petrochemical and natural gas industries — Pressure-relieving and depressuring systems
- ICS
- 75.180.20
- CCS
- 发布
- 2021-07-01
- 实施
