77.140.30 承压钢 标准查询与下载
共找到 334 条与 承压钢 相关的标准，共 23 页
本标准规定了低压和中压锅炉用无缝钢管的尺寸、外形、重量、技术要求、试验方法、检验规则、包装、标志和质量证明书。 本标准适用于制造各种结构低压和中压锅炉及机车锅炉用的优质碳素结构钢热轧（挤、扩）和冷拔（轧）无缝钢管。
Seamless steel tubes for low and medium pressure
- ICS
- 77.140.30
- CCS
- H48
- 发布
- 1999-11-01
- 实施
- 2000-08-01
本标准规定了低温压力容器用低合金钢钢板的尺寸、外形、技术要求、试验方法、检验规则、包装、标志和质量证明书等。 本标准适用于制造-20℃～-70℃低温压力容器用厚度为6mm～100mm低合金钢钢板。
Low alloy steel plates for low temperature pressure vessels
- ICS
- 77.140.30
- CCS
- H46
- 发布
- 1996-04-05
- 实施
- 1996-10-01
本标准规定了焊接气瓶用钢板的尺寸、外形、技术要求、试验方法和检验规则等。 本标准适用于焊接气瓶用厚度为2.5～12.0mm的热轧钢板及厚度为1.5～4.0mm的冷轧钢板。
Steel plates for welded gas cylinders
- ICS
- 77.140.30
- CCS
- H46
- 发布
- 1994-12-22
- 实施
- 1995-10-01
本标准规定了无缝气瓶用钢坯的尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则和包装、标志、质量证明书等内容。 本标准适用于制造高压无缝气瓶用钢坯。
Steel blank for seamless gas cylinder
- ICS
- 77.140.30
- CCS
- H43
- 发布
- 1992-04-24
- 实施
- 1992-12-01
本标准规定用光学金相显微镜来评定球墨铸铁的显微组织。 本标准对球化分级、石墨大小、珠光体粗细、珠光体数量、分散分布的铁素体数量、磷共晶数量和渗碳体数量的评定方法作了规定，列出了评级图。 本标准适用于评定普通和低合金球墨铸铁铸态，正火、退火态的显微组织。
Metallographic test for spheroidal graphite cast iron
- ICS
- 77.140.30
- CCS
- J31
- 发布
- 1988-06-25
- 实施
- 1989-03-01
Standard Specification for Carbon Steel Forgings for Pressure Vessel Components
- ICS
- 77.140.30
- CCS
- 发布
- 2024-05-01
- 实施
Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
- ICS
- 77.140.30
- CCS
- 发布
- 2024-05-01
- 实施
Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
- ICS
- 77.140.30
- CCS
- 发布
- 2024-05-01
- 实施
Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered, Manganese-Molybdenum and Manganese-Molybdenum-Nickel
- ICS
- 77.140.30
- CCS
- 发布
- 2024-03-01
- 实施
- 2024-03-01
Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels
- ICS
- 77.140.30
- CCS
- 发布
- 2023-11-01
- 实施
Standard Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and Tempered
- ICS
- 77.140.30
- CCS
- 发布
- 2023-11-01
- 实施
Standard Specification for Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure Vessels
- ICS
- 77.140.30
- CCS
- 发布
- 2023-11-01
- 实施
Standard Specification for Age-Hardening Alloy Steel Forgings for Pressure Vessel Components
- ICS
- 77.140.30
- CCS
- 发布
- 2023-11-01
- 实施
Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
- ICS
- 77.140.30
- CCS
- 发布
- 2023-11-01
- 实施
Standard Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, Quenched and Tempered, for Welded Pressure Vessels
- ICS
- 77.140.30
- CCS
- 发布
- 2023-11-01
- 实施
Standard Specification for Pressure Vessel Plates, Carbon Steel, High-Strength Manganese
- ICS
- 77.140.30
- CCS
- 发布
- 2023-11-01
- 实施
Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum
- ICS
- 77.140.30
- CCS
- 发布
- 2023-09-01
- 实施
Standard Specification for Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure Vessels
- ICS
- 77.140.30
- CCS
- 发布
- 2023-09-01
- 实施
1.1 This specification2 covers nickel-alloy steel plates intended primarily for welded pressure vessels. 1.2 Plates under this specification are available with four strength levels and two nickel compositions as follows: Grade Nominal Nickel Content % Yield Strength, min, ksi [MPa] Tensile Strength, min, ksi [MPa] A 2.25 37 [255] 65 [450] B 2.25 40 [275] 70 [485] D 3.50 37 [255] 65 [450] E 3.50 40 [275] 70 [485] F 3.50 2 in. [50 mm] and under 55 [380] 80 [550] Over 2 in. [50 mm] 50 [345] 75 [515] 1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel
- ICS
- 77.140.30
- CCS
- 发布
- 2023-07-01
- 实施
1.1 This specification2 covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction.2 Note 1: There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards , Vol 02.04. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
- ICS
- 77.140.30
- CCS
- 发布
- 2023-06-09
- 实施
