81.060.10 原料 标准查询与下载

GB/T 38985-2020 陶瓷液体色料性能技术要求

本标准规定了陶瓷液体色料的分类、技术要求、试验方法、抽样、判定和检验规则、标志、包装、运输和贮存。 本标准适用于需要经过高温烧成形成装饰图案的陶瓷液体色料。

The character requirements for ceramic liquid pigments

GB/T 38904-2020 陶瓷液体色料元素含量测定分析方法

本标准规定了陶瓷液体色料元素含量测定分析方法的试剂、仪器和设备、样品的制备、分析方法、质量控制和试验报告。 本标准适用于陶瓷液体色料产品中元素含量的测定。 可分析陶瓷液体色料中硅、铝、铁、钙、镁、钾、钠、钛、锂、硼、锌、铅、镨、锆、锰、锡、镉、铬、钴、金、银、锑、硒、铈等元素的含量。

Methods for elemental analysis of ceramic liquid pigments

GB/T 29758-2013 陶瓷用熔块

本标准规定了陶瓷用熔块的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于陶瓷用熔块。

Frit for ceramics

GB/T 23460.1-2009 陶瓷釉料性能测试方法.第1部分:高温流动性测试.熔流法

GB/T 23460的本部分规定了陶瓷釉料高温流动性测试方法 熔流法。 本部分适用于建筑卫生陶瓷及日用陶瓷釉料高温流动性的测试。 本部分是一个相对的方法，依据本部分所得的试验结果，只有在试验釉与参比釉各项条件相同的情况下测试才具有可比性。

Test methods of ceramic glazes.Part 1:Determination of fluidity behaviour.Fusion flow test

ASTM C690-09(2024) 用电感应区技术测定氧化铝或石英粉末粒度分布的标准试验方法

Standard Test Method for Particle Size Distribution of Alumina or Quartz Powders by Electrical Sensing Zone Technique

ASTM C371-09(2024) 非塑性陶瓷粉末的丝网筛分析的标准试验方法

Standard Test Method for Wire-Cloth Sieve Analysis of Nonplastic Ceramic Powders

ASTM C1835-16(2023) 纤维增强碳化硅-碳化硅（SiC-SiC）复合结构的标准分类

1.1  This classification covers silicon carbide-silicon carbide (SiC-SiC) composite structures (flat plates, rectangular bars, round rods, and tubes) manufactured for structural components. The SiC-SiC composites consist of continuous silicon carbide fibers in a silicon carbide matrix produced by four different matrix densification methods. 1.2  The classification system provides a means of identifying and organizing different SiC-SiC composites, based on the fiber type, architecture class, matrix densification, physical properties, and mechanical properties. The system provides a top-level identification system for grouping different types of SiC-SiC composites into different classes and provides a means of identifying the general structure and properties of a given SiC-SiC composite. It is meant to assist the ceramics community in developing, selecting, and using SiC-SiC composites with the appropriate composition, construction, and properties for a specific application. 1.3  The classification system produces a classification code for a given SiC-SiC composite, which shows the type of fiber, reinforcement architecture, matrix type, fiber volume fraction, density, porosity, and tensile strength and modulus (room temperature). 1.3.1  For example, Composites Classification Code, SC2-A2C-4D10-33 —a SiC-SiC composite material/component (SC2 ) with a 95 %+ polymer precursor (A ) based silicon carbide fiber in a 2-D (2 ) fiber architecture with a CVI matrix (C ), a fiber volume fraction of 45 % (4 = 40 % to 45 %), a bulk density of 2.3 g/cc (D = 2.0 g/cc to 2.5 g/cc), an apparent porosity of 12 % (10 = 10 % to 15 %), an average ultimate tensile strength of 350 MPa (3 = 300 MPa to 399 MPa), and an average tensile modulus of 380 GPa (3 = 300 GPa to 399 GPa). 1.4  This classification system is a top level identification tool which uses a limited number of composite properties for high level classification. It is not meant to be a complete, detailed material specification, because it does not cover the full range of composition, architecture, physical, mechanical, fabrication, and durability requirements commonly defined in a full design specification. Guide C1793 provides extensive and detailed direction and guidance in preparing a complete material specification for a given SiC-SiC composite component. 1.5  Units— The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification for Fiber Reinforced Silicon Carbide-Silicon Carbide (SiC-SiC) Composite Structures

JC/T 2684-2022 六方氮化硼

本文件规定了六方氮化硼的分类与标记、要求、试验方法、检验规则以及标志、包装、运输和贮存。 本文件适用于经高温煅烧、理化处理、高温精制而成的六方氮化硼粉体，不适用于食品、化妆品等与人身安全相关行业的六方氮化硼。

Hexagonal boron nitride

T/GDAQI 92-2022 陶瓷制品 铝、银、砷等18种元素迁移量的测定 电感耦合等离子体发射光谱法

本文件规定了食品接触用陶瓷制品在食品模拟物中浸泡后铝、银、砷、钡、镉、钴、铬、铜、锂、锰、钼、镍、铅、锑、钒、锌、铁、钛迁移量测定的电感耦合等离子体发射光谱法。 本文件适用于食品接触用陶瓷制品中铝、银、砷、钡、镉、钴、铬、铜、锂、锰、钼、镍、铅、锑、钒、锌、铁、钛迁移量的测定。

Determination of migration of 18 elements such as aluminum, silver and arsenic in ceramic products Inductively coupled plasma emission spectrometry

T/QGCML 347-2022 气凝胶复合A级聚苯不燃型保温板

本文件规定了气凝胶复合A级聚苯不燃型保温板的术语和定义、分类、一般要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于气凝胶复合A级聚苯不燃型保温板的生产及检验。

Airgel composite grade A polystyrene non-combustible insulation board

T/QGCML 343-2022 纳米二氧化硅气凝胶粉体

本文件规定了纳米二氧化硅气凝胶粉体的术语和定义、分类、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于纳米二氧化硅气凝胶粉体生产及检验。

Nano silica airgel powder

T/QGCML 344-2022 纳米二氧化硅气凝胶毡

本文件规定了纳米二氧化硅气凝胶毡的术语和定义、分类、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于纳米二氧化硅气凝胶毡的生产及检验。

Nano silica airgel felt

T/QGCML 348-2022 气凝胶绝热板

本文件规定了气凝胶绝热板的术语和定义、分类、一般要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于气凝胶绝热板的生产及检验。

Airgel Insulation Panel

T/CBCSA 45-2022 陶瓷数码釉

本文件规定了陶瓷数码釉的术语和定义、分类、要求、试验方法、抽样、判定和检验规则、标志、包装、运输和贮存。

Digital ceramic glaze

ASTM C1069-09(2022) 用氮吸附法测定氧化铝或石英比表面积的标准试验方法

1.1 This test method covers the determination of the specific surface area of aluminas and silicas used in the manufacture of ceramics. The test method is a general one, permitting the use of any modern commercial nitrogen adsorption apparatus but strictly defining the outgassing procedure. Calculations are based on the Brunauer-Emmett-Teller (BET) equation. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Specific Surface Area of Alumina or Quartz by Nitrogen Adsorption

ASTM C867-94(2022) 陶瓷白瓷粘土中可溶性硫酸盐的标准试验方法（光度法）

1.1 This test method covers the determination of soluble sulfate ions present in water or a filtrate by means of a photometer measuring the turbidity of precipitated barium sulfate. A method of standardizing the photometer for this test method is also given. 1.2 Soluble sulfate ions may be removed from clays or clay-water slurries by leaching with water during mixing and subsequent filter pressing. To remove all the sulfate ions would require an impractical number of washings; therefore, this test method should be considered a control test and not a quantitative analysis for SO4 ions. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Soluble Sulfate in Ceramic Whiteware Clays (Photometric Method)

ASTM C324-01(2022) 陶瓷白瓷粘土中游离水分的标准试验方法

Standard Test Method for Free Moisture in Ceramic Whiteware Clays

ASTM C324-01(2022)e1 卫生陶瓷粘土中游离水的试验方法

1.1 This test method covers the determination of free moisture in ceramic whiteware clays. Whiteware clays may be shipped as a bulk shipment in lumps, a bulk shipment of shredded or coarsely ground clay, or in bagged lots of ground or airfloated clay. Directions are given in this test method for obtaining representative samples of the clay shipment to be used in subsequent tests for the properties of the clay in the shipment. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Free Moisture in Ceramic Whiteware Clays

ASTM C958-92(2022) 用X射线重力沉降监测法测定氧化铝或石英粒度分布的标准试验方法

1.1 This test method covers the determination of the particle size distribution of alumina or quartz powders in the range from 0.5 µm to 50 µm and having a median particle diameter from 2.5 µm to 10 µm using a sedimentation method. This test method is one of several found valuable for the measurement of particle size. Instruments used for this test method employ a constant intensity X-ray beam that is passed through a sedimenting dispersion of particles. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Particle Size Distribution of Alumina or Quartz by X-Ray Monitoring of Gravity Sedimentation

T/LZLSF 0011-2022 预包装柳州螺蛳粉原辅料采购管理指南

本文件界定了柳州螺蛳粉原辅料的术语和定义，规定了采购、验收、入库、贮藏等相关管理要求。

Purchasing Management Guide for Raw Materials and Excipients of Prepackaged Liuzhou Snail Rice Noodles