83.080.01;83.120 标准查询与下载

GOST 32656-2017 聚合物复合材料. 试验方法. 拉伸试验方法

Polymer composites. Test methods. Tensile test methods

GOST 32656-2014 聚合物复合材料. 试验方法. 拉伸试验方法

Polymer composites. Test methods. Tensile test methods

DS/EN ISO 10350-1:2008 塑料 可比单点数据的采集和呈现 第1部分：成型材料

ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions.The properties included are those presented conventionally in manufacturers' data sheets. This part of ISO 10350 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness. Part 2 of ISO 10350 deals specifically wit

Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials

LST EN ISO 20200:2005 塑料 在实验室规模试验中模拟堆肥条件下塑料材料分解程度的测定（ISO 20200:2004）

Plastics - Determination of the degree of disintegration of plastic materials under simulated composting conditions in a laboratory-scale test (ISO 20200:2004)

ISO 10350-2:2001 塑料 可比单点数据的采集和表示 第2部分：长纤维增强塑料

ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions or along different directions in the material. The properties included are those presented conventionally in manufacturers' data sheets. This part of ISO 10350 applies to reinforced thermoplastic and thermosetting materials where the reinforcement fibres are either discontinuous with a fibre length prior to processing greater than 7,5 mm or continuous (e.g. fabric, continuous-strand mat or unidirectional). Part 1 of this International Standard deals specifically with unreinforced and filled plastics, including those using fibres less than 7,5 mm in length.

Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics

NF T51-120-5:1995 塑料和复合材料 弯曲疲劳性能的测定 - 第5部分：恒力矩弯曲试验

Plastiques et composites - Détermination des propriétés de fatigue en flexion - - Partie 5 : essai en flexion à moment constant.

NF T51-120-2:1995 塑料和复合材料 弯曲疲劳性能的测定 第2部分：嵌入式样品的弯曲试验

Plastiques et composites - Détermination des propriétés de fatigue en flexion - Partie 2 : essai en flexion sur éprouvettes encastrées.

NF T51-120-6:1995 塑料和复合材料 弯曲疲劳特性的测定 - 第6部分：燃烧时弯曲的论述

Plastiques et composites - Détermination des propriétés de fatigue en flexion - - Partie 6 : essai de flexion par flambement.

NF T51-120-1:1995 塑料和复合材料 弯曲疲劳特性的测定 - 第1部分：一般原理

Plastiques et composites - Détermination des propriétés de fatigue en flexion - - Partie 1 : principes généraux.

NF T51-120-4:1995 塑料和复合材料 弯曲疲劳特性的测定 第4部分：讨论非弯曲疲劳的四个弯曲点

Plastiques et composites - Détermination des propriétés de fatigue en flexion - Partie 4 : essai en flexion quatre points sur éprouvettes non encastrées.

NF T51-120-3:1995 塑料和复合材料 弯曲疲劳特性的测定 - 第3部分：讨论非弯曲的弯曲三点

Plastiques et composites - Détermination des propriétés de fatigue en flexion - - Partie 3 : essai en flexion trois points sur éprouvettes non encastrées.