83.140.20 层压薄板 标准查询与下载

GB/T 41003.1-2021 塑料泡沫垫通用技术条件 第1部分：聚乙烯/乙烯-醋酸乙烯酯共聚物儿童泡沫垫

/乙烯-醋酸乙烯酯共聚物(本文件规定了聚乙烯(PE)EVA)儿童泡沫垫的理化性能、试验方法及检验规则。 本文件适用于以低密度聚乙烯、乙烯醋酸乙烯酯共聚物及其混合物等为主要原料,加入发泡剂、交联剂等助剂,经模压发泡法生产及后加工而制成的儿童泡沫垫。

General technical specification for plastic foam mats—Part 1:Polyethylene/ethylene vinylacetate copolymer foam mats for children

GB/T 40426.3-2021 塑料制品 装饰性实体面材 第3部分：性能的测定 非板型实体面材

本文件描述了非板型实体面材各项性能的试验方法。 本文件适用于GB/T404

Plastics—Decorative solid surfacing materials—Part 3:Determination of properties—Non-sheet solid surfacing material

GB/T 40426.2-2021 塑料制品 装饰性实体面材 第2部分：性能的测定 板型实体面材

本文件描述了板型实体面材的各性能的试验方法。 本文件适用于GB/T40426.1 规定的材料。这些方法可用于测试板型实体面材制品,但测试一般是在尺寸满足试验要求的平板上进行;所测试的平板材质和表面处理与板型实体面材相同。

Plastics—Decorative solid surfacing materials—Part 2: Determination of properties—Sheet solid surfacing material

GB/T 40426.1-2021 塑料制品 装饰性实体面材 第1部分：分类和规范

本文件规定了实体面材的术语和定义、分类、要求、试验方法、检验规则以及包装、标志、运输和贮存。 本文件适用于板型实体面材和非板型实体面材,其他具有类似用途的产品也可参照执行。

Plastics—Decorative solid surfacing materials—Part 1: Classification and specifications

GB/T 4454-1996 硬质聚氯乙烯层压板材

本标准规定了硬质聚氯乙烯层压板材（以下简称板材）的产品分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于以聚氯乙烯树脂为主要原料，加入稳定剂和其他助剂，经压延成薄片，再经层压制得的板材。

Rigid polyvinyl chloride laminated plates

ASTM D3917-23 热固性玻璃增强塑料拉挤型材的尺寸公差标准规范

Standard Specification for Dimensional Tolerance of Thermosetting Glass-Reinforced Plastic Pultruded Shapes

ASTM D6873/D6873M-23 聚合物基复合材料层压板的轴承疲劳响应的标准实施规程

Standard Practice for Bearing Fatigue Response of Polymer Matrix Composite Laminates

ASTM D3479/D3479M-19(2023) 聚合物基复合材料拉伸-拉伸疲劳的标准试验方法

Standard Test Method for Tension-Tension Fatigue of Polymer Matrix Composite Materials

ASTM D4762-23 聚合物基复合材料试验的标准指南

Standard Guide for Testing Polymer Matrix Composite Materials

ASTM D8066/D8066M-23 聚合物基复合材料层压板无缺口压缩试验的标准实践

1.1 This practice provides instructions for using the Test Method D6484/D6484M open hole compression test fixture to determine unnotched compressive strength of multi-directional laminates. The composite material forms are limited to continuous-fiber reinforced polymer matrix composites in which the laminate is both symmetric and balanced with respect to the test direction. The range of acceptable test laminates and thicknesses are described in 8.2.1. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.2.1 Within the text the inch-pound units are shown in brackets. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice Unnotched Compression Testing of Polymer Matrix Composite Laminates

ASTM D8131/D8131M-23 聚合物基复合材料层压材料锥形和阶梯接头拉伸性能的标准实施规程

1.1 This test practice defines the procedure for determination of the tensile strength of a tapered or stepped joint of polymer matrix composite materials. It is applicable to secondary bonded or co-bonded laminates with either unidirectional plies or woven fabric reinforcements. The materials to be bonded may be different material systems. In the bondline, a separate adhesive material may or may not be used (example: adhesives may be used with a prepreg system or may not be used with a wet lay-up repair system). The range of acceptable test laminates and thicknesses is described in 8.2.1. 1.2 This practice supplements Test Method D3039/D3039M for tensile loading. Several important test specimen parameters (for example, joint length, ply overlaps, step depth, and taper ratio) are not mandated by this practice, however, these parameters are required to be specified and reported to support repeatable results. 1.3 Unidirectional (0° ply orientation) tape composites, textile composites, as well as multidirectional composite laminates, can be tested. 1.4 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4.1 Within the text the inch-pound units are shown in brackets. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Tensile Properties of Tapered and Stepped Joints of Polymer Matrix Composite Laminates

ASTM C582-23 耐腐蚀设备用接触模压增强热固性塑料（RTP）层压板的标准规范

1.1 This specification covers composition, thickness, fabricating procedures, and physical property requirements for glass fiber reinforced thermoset polyester, vinyl ester, or other qualified thermosetting resin laminates comprising the materials of construction for RTP corrosion-resistant tanks, piping, and equipment. This specification is limited to fabrication by contact molding. NOTE 1—The laminates covered by this specification are manufactured during fabrication of contact-molded RTP tanks, piping, and other equipment. NOTE 2—There is no known ISO equivalent to this standard. 1.2 The values stated in inch-pound units are to be regarded as standard. The SI values given in parentheses are conversions from inch-pound units and are for information only. 1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment

ASTM D2344/D2344M-22 聚合物基复合材料及其层压板短梁强度的标准试验方法

1.1 This test method determines the short-beam strength of high-modulus fiber-reinforced composite materials. The specimen is a short beam machined from a curved or a flat laminate up to 6.00 mm [0.25 in.] thick. The beam is loaded in three-point bending. 1.2 Application of this test method is limited to continuousor discontinuous-fiber-reinforced polymer matrix composites, for which the elastic properties are balanced and symmetric with respect to the longitudinal axis of the beam. 1.3 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3.1 Within the text, the inch-pound units are shown in brackets. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates

ASTM F904-22 层压柔性材料粘合强度层分离的标准实施规程

1.1 This practice describes techniques for separating plies of laminates made from flexible materials such as cellulose, paper, plastic film, and foil to enable the measurement of the bond strength or ply adhesion of the laminate. This includes laminates made by various processes: adhesive laminates, extrusion coatings, extrusion laminates, and coextrusions. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 6.1.1. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Separation of Plies for Bond Strength of Laminated Flexible Materials

ASTM D5449/D5449M-22 环形缠绕聚合物基复合材料圆筒横向压缩性能的标准试验方法

1.1 This test method determines the transverse compressive properties of wound polymer matrix composites reinforced by high-modulus continuous fibers. It describes testing of hoop wound (90°) cylinders in axial compression for determination of transverse compressive properties. 1.2 The technical content of this test method has been stable since 1993 without significant objection from its stakeholders. As there is limited technical support for the maintenance of this test method, changes since that date have been limited to items required to retain consistency with other ASTM D30 Committee standards, including editorial changes and incorporation of updated guidance on specimen preconditioning and environmental testing. The test method, therefore, should not be considered to include any significant changes in approach and practice since 1993. Future maintenance of the test method will only be in response to specific requests and performed only as technical support allows. 1.3 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3.1 Within the text, the inch-pound units are shown in brackets. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Transverse Compressive Properties of Hoop Wound Polymer Matrix Composite Cylinders

ASTM D5450/D5450M-22 环形缠绕聚合物基复合材料圆筒横向拉伸性能的标准试验方法

1.1 This test method determines the transverse tensile properties of wound polymer matrix composites reinforced by high-modulus continuous fibers. It describes testing of hoop wound (90°) cylinders in axial tension for determination of transverse tensile properties. 1.2 The technical content of this test method has been stable since 1993 without significant objection from its stakeholders. As there is limited technical support for the maintenance of this test method, changes since that date have been limited to items required to retain consistency with other ASTM D30 Committee standards, including editorial changes and incorporation of updated guidance on specimen preconditioning and environmental testing. The test method, therefore, should not be considered to include any significant changes in approach and practice since 1993. Future maintenance of the test method will only be in response to specific requests and performed only as technical support allows. 1.3 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3.1 Within the text, the inch-pound units are shown in brackets. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Transverse Tensile Properties of Hoop Wound Polymer Matrix Composite Cylinders

ASTM E1922/E1922M-22 层压和拉挤聚合物基复合材料层间断裂韧性的标准试验方法

1.1 This test method covers the determination of translaminar fracture toughness, KTL, for laminated, molded, or pultruded polymer matrix composite materials of various fiber orientations using test results from monotonically loaded notched specimens. If the material response is such that the KTL calculation is not valid, alternate reporting methods are provided. 1.2 This test method is applicable to room temperature laboratory air environments. 1.3 Composite materials that can be tested by this test method are not limited by thickness or by type of polymer matrix or fiber, provided that the specimen sizes and the test results meet the requirements of this test method. This test method was developed primarily from test results of various carbon fiber – epoxy matrix laminates and from additional results of glass fiber – epoxy matrix, glass fiber-polyester matrix pultrusions and carbon fiber – bismaleimide matrix laminates (1-4, 5, 6).2 1.4 A range of eccentrically loaded, single-edge-notch tension, ESE(T), specimen sizes with proportional planar dimensions is provided, but planar size may be variable and adjusted, with associated changes in the applied test load. Specimen thickness is a variable, independent of planar size. 1.5 Specimen configurations other than those contained in this test method may be used. It is particularly important that the requirements discussed in 5.1 and 5.4 regarding contained notch-tip damage be met when using alternative specimen configurations in conjunction with the KTL calculation. 1.6 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6.1 Within the text, the inch-pound units are shown in brackets. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Translaminar Fracture Toughness of Laminated and Pultruded Polymer Matrix Composite Materials

BS EN ISO 19712-3:2022 塑料 装饰性实体面材 性质的测定 固体表面形状

1   Scope This document specifies the methods of test for determination of the properties of solid surfacing materials , as defined in Clause 3, in the form of shaped products. These methods are primarily intended for testing the materials specified in ISO 19712‑1. The tests can be carried out on finished products, but are generally carried out on test panels of a size sufficient to meet the requirements of the test, and of the same material and finish as the finished product.

Plastics. Decorative solid surfacing materials. Determination of properties. Solid surface shapes

EN ISO 19712-3:2022 塑料.装饰性固体表面材料.第3部分:性能测定.固体表面形状

This document specifies the methods of test for determination of the properties of solid surfacing materials, as defined in Clause 3, in the form of shaped products. These methods are primarily intended for testing the materials specified in ISO 19712-1. The tests can be carried out on finished products, but are generally carried out on test panels of a size sufficient to meet the requirements of the test, and of the same material and finish as the finished product.

Plastics - Decorative solid surfacing materials - Part 3: Determination of properties - Solid surface shapes (ISO 19712-3:2022)

ISO 19712-3:2022 塑料.装饰性固体表面材料.第3部分:性能测定.固体表面形状

This document specifies the methods of test for determination of the properties of solid surfacing materials, as defined in Clause 3, in the form of shaped products. These methods are primarily intended for testing the materials specified in ISO 19712-1. The tests can be carried out on finished products, but are generally carried out on test panels of a size sufficient to meet the requirements of the test, and of the same material and finish as the finished product.

Plastics — Decorative solid surfacing materials — Part 3: Determination of properties — Solid surface shapes