83.140.50;91.140.60;91.140.80 标准查询与下载

GB/T 27572-2011 橡胶密封件 110℃热水供应管道的管接口密封圈 材料规范

本标准规定了饮用和非饮用热水（达110℃）供应管道用的硫化橡胶密封圈的材料要求。 本标准规定的各种密封圈的识别代码是根据密封圈的型式、用途及要求确定的。 本标准对成品密封圈也规定了一般要求。对于特殊用途所需的额外要求应在相应的产品标准中规定。应提请注意的是，管道接口的工作性能与密封圈材料的性能、密封圈的几何形状及管接口的结构有关。如适用，本标准应同规定管接口工作性能的产品标准一起使用。 本标准适用于铸铁管、钢管、陶瓷管、石棉水泥管、水泥管、钢筋水泥管、塑料管及玻璃纤维增强塑料管等所有管接口密封圈。 本标准适用于复合的或非复合的密封圈的弹性体部分。对于硬度范围在76IRHD～95IRHD的材料制成的复合密封圈,只有当材料参与密封作用或要求密封圈的长期稳定时才适用拉断伸长率、压缩永久变形及应力松弛要求。 本标准不适用于由多孔橡胶材料或闭孔材料作为其结构的一部分而制成的接口密封圈。

Rubber seals.Joint rings for pipelines for hot-water supply up to 110 ℃.Specification for the materials

GB/T 21874-2008 弹性体密封件.排水管道接口密封件材料要求.热塑性弹性体

本标准规定了成品密封圈的一般要求。对于特殊用途所需的额外要求应在相应的产品标准中规定。应注意：管道接口的工作性能与密封圈材料的性能、密封圈的几何形状及管接口的结构有关。 本标准适用于下列管道用的热塑性弹性体密封圈材料： a)建筑物内用排污管(对间歇流动水，工作温度可达95℃)； b)埋地用排水管、污水管(对连续流动水，工作温度在45℃以下；对间歇流动水，工作温度可达95℃)； c)雨水管。

Elastomeric seals.Requirements for materials for pipe joint seals used in water and drainage applications.Thermoplastic elastomers

GB/T 21873-2008 橡胶密封件.给、排水管及污水管道用接口密封圈.材料规范

本标准规定了下列管道用的硫化橡胶密封圈材料的要求： a)冷饮用水(50℃以下)供应管； b)排水管、污水管及雨水管(对连续流动水，工作温度在45℃以下；对间歇流动水，工作温度可达95℃)。 本标准规定的各种密封圈的识别代码是根据密封圈的型式、用途及要求确定的(见表3)。 本标准对成品密封圈也规定了一般要求，对于特殊用途所需的额外要求应在相应的产品标准中规定。应提请注意的是，管道接口的工作性能与密封圈材料的性能、密封圈的几何形状及管接口的结构有关。如适用，本标准应同规定管接口工作性能的产品标准一起使用。 本标准适用于包括铸铁管、钢管、陶瓷管、石棉水泥管、水泥管、钢筋水泥管、塑料管及玻璃纤维增强塑料管等所有管道接口密封圈。 本标准适用于复合的或非复合的橡胶密封圈的弹性体部分。对于材料的硬度范围在76 IRHD～95 IRHD之间的复合密封圈，只有橡胶直接参与密封或要求密封圈长期稳定时才使用拉断伸长率、压缩永久变形及应力松弛等要求。 由闭孔材料作为密封圈一部分而制成的接口密封圈也属于本标准的范围。

Rubber seals.Joint rings for water supply,drainage and sewerage pipelines.Specification for materials

ISO 4633:2015 橡胶密封.供水、排水和污水管道用密封圈.材料规范

Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials

KS M ISO 4633:2013 橡胶室.供水.排水及下水排管用方向接头环.材料要求事项

이 표준은 다음과 같은 환경에서 사용되는 가황된 고무 씰(rubber seal)용 재료의 요구 성능을 규정한다.a) 냉 음용수 공급(50 ℃까지)b) 배수, 하수 및 빗물 시스템(45 ℃까지 연속 흐름 및 95 ℃까지 간헐적인 흐름)규정된 씰에 관한 호칭은 종류, 용도 및 요건에 따라 정의된다(표 3 참조).또한 완제품 조인트 씰에 관한 일반 요구사항이 제시되고 파이프 조인트의 성능이 씰 재료의 특성,씰의 형상과 파이프 조인트의 설계에 관한 함수임을 고려하여 특수한 용도의 부가적인 요구사항이관련 제품 표준에 규정되었다.이 표준은 철, 강철, 점토, 섬유 시멘트, 콘크리트, 강화 콘크리트, 플라스틱 및 유리 강화 플라스틱을포함한 모든 종류의 배관에 사용되는 조인트 씰에 적용할 수 있다.이 표준은 복합 재료 씰 또는 비복합 재료 씰의 탄성 부품에 적용할 수 있다. 경도 범위가 76∼95 IRHD인 재료에 관한 복합 재료 씰의 경우에는 재료가 밀봉 기능(sealing function) 또는 씰의 장기적 안정성이 요구될 때에만 파단 신율, 영구 압축 줄음률 및 응력 완화에 관한 요건이 적용된다.설계에 따라 기포가 포함된 조인트 씰도 이 표준의 적용범위에 포함된다.

Rubber seals-Joint rings for water supply, drainage and sewerage pipelines-Specification for materials

SANS 4633:2008 橡胶密封.供水、排水和污水管道用密封圈-材料规范

Specifies requirements for materials used in vulcanized rubber seals for cold drinking-water supplies (up to 50 degrees celsius), and drainage, sewerage and rainwater systems (continuous flow up to 45 degrees celsius and intermittent flow up to 95 degree

Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials

SANS 23711:2008 弹性体密封件.排水管道接口密封件材料要求.热塑性弹性体

Specifies requirements for materials used for moulded seals made of thermoplastic elastomers (TPEs) for joints in thermoplastic piping systems for non-pressure waste water discharge (intermittent flow at up to 95 degrees celsius) inside buildings, underg

Elastomeric seals - Requirements for materials for pipe joint seals used in water and drainage applications - Thermoplastic elastomers

DS/EN 681-4/A2:2005 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 4：铸造聚氨酯密封元件

This standards specifies requirements for materials used in factory cast polyurethane sealing elements used in joints for drainage, sewerage and rainwater systems and non potable water supply for continuous flow up to 45°C.

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - 4: Cast polyurethane sealing elements

DS/EN 681-2/A2:2005 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 第2部分：热塑性弹性体

This Standard specifies requirements for materials used for moulded seals only of thermoplastic elastomeres (TPE) used in joints of: 1) thermoplastic piping systems for non-pressure waste water discharge (intermittent flow up to 95°C ) inside buildings; 2) thermoplastic piping systems for non-pressure underground drainage and sewerage (continuous flow up to 45°C and intermittent flow up to 95°C).

Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers

DS/EN 681-3/A2:2005 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 第3部分：硫化橡胶的多孔材料

This standard specifies requirements for materials used in vulcanized rubber seals of cellular materials for non pressurized drainage, sewerage and rainwater systems and non-pressure non-potable water supply (continuous flow up to 45°C).

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber

ISO 23711:2003 弹性密封件.灌溉和排水设施用管接头密封件材料的要求.弹性塑料

This International Standard specifies requirements for materials used for moulded seals made of thermoplastic elastomers (TPEs) for joints in: a) thermoplastic piping systems for non-pressure waste water discharge (intermittent flow at up to 95 °C) inside buildings; b) thermoplastic piping systems for non-pressure underground drainage and sewerage (continuous flow at up to 45 °C and intermittent flow at up to 95 °C); c) thermoplastic rainwater piping systems. General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design.

Elastomeric seals - Requirements for materials for pipe joint seals used in water and drainage applications - Thermoplastic elastomers

DS/EN 681-4/A1:2003 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 第4部分：铸造聚氨酯密封元件

This standards specifies requirements for materials used in factory cast polyurethane sealing elements used in joints for drainage, sewerage and rainwater systems and non potable water supply for continuous flow up to 45°C.

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 4: Cast polyurethane sealing elements

DS/EN 681-3/A1:2003 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 第3部分：硫化橡胶的多孔材料

This standard specifies requirements for materials used in vulcanized rubber seals of cellular materials for non pressurized drainage, sewerage and rainwater systems and non-pressure non-potable water supply (continuous flow up to 45°C).

Elastomeric seals - Material requirements for pipe joints seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber

DS/EN 681-2/A1:2003 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 第2部分：热塑性弹性体

This standard specifies requirements for materials used for moulded seals only of thermoplastic elastomeres (TPE) used in joints of: 1) thermoplastic piping systems for non-pressure waste water discharge (intermittent flow up to 95°C ) inside buildings; 2) thermoplastic piping systems for non-pressure underground drainage and sewerage (continuous flow up to 45°C and intermittent flow up to 95°C).

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers

DS/EN 681-4:2000 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 第4部分：铸造聚氨酯密封元件

This standards specifies requirements for materials used in factory cast polyurethane sealing elements used in joints for drainage, sewerage and rainwater systems and non potable water supply for continuous flow up to 45°C.

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 4: Cast polyurethane sealing elements

DS/EN 681-3:2000 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 第3部分：硫化橡胶的多孔材料

This standard specifies requirements for materials used in vulcanized rubber seals of cellular materials for non pressurized drainage, sewerage and rainwater systems and non-pressure non-potable water supply (continuous flow up to 45°C).

Elastomeric seals - Materials requirements for pipe joints seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber

DS/EN 681-2:2000 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 第2部分：热塑性弹性体

This Standard specifies requirements for materials used for moulded seals only of thermoplastic elastomeres (TPE) used in joints of: 1) thermoplastic piping systems for non-pressure waste water discharge (intermittent flow up to 95°C ) inside buildings; 2) thermoplastic piping systems for non-pressure underground drainage and sewerage (continuous flow up to 45°C and intermittent flow up to 95°C).Pkt. 3. Thermoplastic rainwater piping system

Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers

DS 521/Ret.1:1999 用于水和废水管道的橡胶密封圈

The standard specifies requirements and methods of test for solid rubber sealing rings for water and waste-water piping.

Rubber sealing rings for water and waste-water piping