91.190 建筑附件 标准查询与下载

GB/T 32223-2015 建筑门窗五金件 通用要求

本标准规定了建筑门窗五金件的术语和定义、分类、一般要求、要求、试验方法。 本标准适用于除门控五金件外的建筑门窗常用五金件。

Building hardware for windows and doors.General requirements

24/30483336 DC 草案 BS EN 1303 建筑硬件 锁芯和主钥匙系统 (MKS) 要求和测试方法

Draft BS EN 1303 Building hardware — Cylinders and Master-Key-Systems (MKS) for locks — Requirements and test methods

23/30478026 DC BS EN 13126-9 建筑硬件 窗户和门高窗户的五金件 要求和测试方法 第9部分：水平和垂直旋转窗的硬件

BS EN 13126-9. Building hardware. Hardware for windows and door height windows. Requirements and test methods - Part 9. Hardware for horizontal and vertical pivot windows

ASTM A153/A153M-23 钢铁五金器具镀锌 (热浸) 的标准规格

1.1  This specification covers zinc coatings applied by the hot-dip process on iron and steel hardware. The hot-dip galvanizing process consists of parts being immersed in molten zinc for a sufficient time to allow a metallurgical reaction between iron from the steel surface and the molten zinc, resulting in the formation of Zn/Fe alloy layers bonding the coating to the steel surface. 1.2  This specification is intended to be applicable to hardware items that are centrifuged or otherwise handled to remove excess galvanizing bath metal (free zinc). Coating thickness grade requirements reflect this. 1.3  Fasteners that must comply with the Fastener Quality Act require specific statistical sampling during the inspection of the fastener lots. Requirements for the sampling of these fasteners can be found in F2329/F2329M . 1.4  This specification is applicable to orders in either inch-pound units (as A153 ) or in SI units (as A153M ). Inch-pound units and SI units are not necessarily exact equivalents. Within the text of this specification and where appropriate, SI units are shown in brackets. Each system shall be used independently of the other without combining values in any way. In the case of orders in SI units, all testing and inspection shall be done using the metric equivalent of the test or inspection method as appropriate. In the case of orders in SI units, such shall be stated to the galvanizer when the order is placed. 1.5  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware

T/QGCML 804-2023 卫浴控水结构

本文件规定了卫浴控水结构的术语和定义、产品结构、技术要求、试验方法、检验规则、标志、合格证书、使用说明书、包装、运输和贮存。 本文件适用于安装在卫浴间内的控水结构，其他场所的控水结构可参照使用。

Bathroom water control structure

23/30468034 DC BS EN 16867 AMD 2. 构建硬件 机电一体化门家具 要求及测试方法

BS EN 16867 AMD 2. Building hardware. Mechatronic door furniture. Requirements and test methods

T/CECS 1280-2023 机电工程装配式支吊架安装及验收规程

本规程共分6章和3个附录，主要内容包括：总则、术语、基本规定、材料、安装施工、验收等。

Procedures for installation and acceptance of prefabricated supports and hangers in electromechanical engineering

BS EN 13126-3:2023 建筑硬件 窗户和门高窗的五金件 要求和测试方法 手柄 主要用于倾斜和转动、倾斜优先和仅转动硬件

1   Scope This part of the EN 13126 series specifies the requirements and test procedures for durability, strength, security and functionality of handles . This document is applicable to Tilt and Turn, Tilt-First and Turn-Only hardware for use on windows and door-height windows. Handles can also be used on other opening types, e.g. on In-line Sliding, Tilt and Slide, Sliding Folding, horizontal and vertical-pivoting windows. This document is not applicable to: a) operation devices, door handles for door latches and door locks (for this, refer to EN 1906); b) handles with handle length > 170 mm (refer to Figure B.1).

Building hardware. Hardware for windows and door - height windows. Requirements and test methods. Handles, primarily for Tilt and Turn, Tilt-First and Turn-Only hardware

T/ZJWJ 001-2022 闭门器

（一）该标准主要依据行业标准QB/T 2698-2013《闭门器》,同时结合了国内外优秀同类生产企业先进产品的技术要求编制而成。标准编写结构合理、内容叙述正确、层次清晰，引用标准现行有效，符合GB/T 1.1-2020的规定。 （二）该标准按照团体标准的定位和要求制定，在编制过程中广泛征求、采纳了各方的意见和建议，同时结合了闭门器产业现状和发展方向，可操作性强。标准中设置的技术指标和要求均可验证、可检测，试验方法均有标准作支撑，可转化为认证实施细则。 （三）该标准提出了闭门器的术语和定义、产品分类、技术要求、试验条件、试验方法、检验规则、标志、包装、运输及贮存，标准的主要技术指标要求达到了国内一流、国际先进水平，符合团体标准的基本要求。 与QB/T 2698-2013《闭门器》要求相比，主要先进性体现如下： 1）提高了闭门器寿命次数，提升产品的寿命性能； 2）增加了闭门器的抗干扰要求，更符合现有产品的使用环境，提升了产品的使用环境性能要求。 （四）该标准的制订、发布与实施将规范闭门器产品的技术要求，提升产品的市场竞争力，有利于提高产品的技术水平。

door closer

T/CASME 78-2022 建筑用变间距遮阳导光金属百叶窗

本文件规定了建筑用变间距遮阳导光金属百叶窗的材料和配件、要求、试验方法、检验规则、标志、包装、运输和贮存。

Variable pitch metal louvers for shading and light guiding for buildings

BS EN 1527:2019+A1:2021 建筑硬件 滑动门和折叠门的五金件 要求及测试方法

Building hardware. Hardware for sliding doors and folding doors. Requirements and test methods

BS EN 13126-16:2019 建筑硬件 窗户和门高窗户的五金件 要求和测试方法 升降窗和滑动窗的硬件

1   Scope This document specifies requirements and test methods for durability, strength, security and function of hardware for Lift and Slide windows and door height windows in accordance with common application as shown in Figures C.1 and C.2 in informative Annex C, regardless of whether the hardware enables an additional tilt position. NOTE 1 This document is also applicable to hardware systems, whereby the sash itself is not lifted but a gasket mechanism is moved. NOTE 2 This document is also applicable to hardware systems, whereby the sash itself is not lifted but the sash is being moved parallel to the plane of the frame.

Building hardware. Hardware for windows and door height windows. Requirements and test methods - Hardware for Lift and Slide windows

BS EN 17610:2022 建筑硬件 环保产品声明 建筑硬件 EN 15804 的补充产品类别规则

1   Scope This document provides product category rules (PCR) for Type III environmental declarations for: — Building hardware products for opening and closing doors, gates, windows and shutters: — Lever handles and knob furniture (EN 1906); — Single-axis hinges (EN 1935); — Hardware for windows and door height windows (EN 13126 (all parts)); — Fittings for shutters (e.g. EN 14648); — Controlled door closing devices, electrically powered hold-open devices for swing doors and door coordinator devices (EN 1154, EN 1155, EN 1158); — Hardware for sliding doors, folding doors and roll fronts (EN 1527, EN 15706); — Glass door gear;

Building hardware. Environmental product declarations. Product category rules complementary to EN 15804 for building hardware

EN 17610:2022 建筑五金 环境产品声明 补充建筑五金 EN 15804 的产品类别规则

This document provides product category rules (PCR) for Type III environmental declarations for: - Building hardware products for opening and closing doors, gates, windows and shutters: -- Lever handles and knob furniture (EN 1906); -- Single-axis hinges (EN 1935); -- Hardware for windows and door height windows (EN 13126 (all parts)); -- Fittings for shutters (e.g. EN 14648); -- Controlled door closing devices, electrically powered hold-open devices for swing doors and door coordinator devices (EN 1154, EN 1155, EN 1158); -- Hardware for sliding doors, folding doors and roll fronts (EN 1527, EN 15706); -- Glass door gear; - Building hardware products for locking and unlocking doors, gates, windows and shutters: -- Mechanically operated locks and locking plates, multipoint locks, latches and locking plates (EN 12209, EN 15685 ); -- Cylinders for locks (EN 1303); -- Padlocks and padlock fittings (EN 12320); -- Mechanically operated push-button locksets (BS 8607); -- Emergency exit devices operated by a lever handle or push pad, for use on escape routes and panic exit devices operated by a horizontal bar, for use on escape routes (EN 179, EN 1125); - Electromechanical building hardware products: -- Mechatronic cylinders (EN 15684); -- Mechatronic padlocks (EN 16864); -- Mechatronic door furniture (EN 16867); -- Electromechanically operated locks and striking plates (EN 14846); -- Electrically controlled exit systems for use on escape routes (EN 13637). This document complements the core rules for the product category of construction products as defined in the European standard EN 15804:2012+A2:2019. NOTE The assessment of social and economic performances at product level is not covered by this document. The core PCR: - defines the parameters to be declared and the way in which they are collated and reported; - describes which stages of a product’s life cycle are considered in the EPD and which processes are to be included in the life cycle stages; - defines rules for the development of scenarios; - includes the rules for calculating the Life Cycle Inventory and the Life Cycle Impact Assessment underlying the EPD, including the specification of the data quality to be applied; - includes the rules for reporting the predetermined, environmental and health information that is not covered by Life Cycle Assessment (LCA) for the product, construction process(es) and construction service(s), as relevant; - defines the conditions under which construction products can be compared based on the information provided by EPD. For the EPD of construction services the same rules and requirements apply as for the EPD of construction products.

Building hardware - Environmental product declarations - Product category rules complementary to EN 15804 for building hardware

22/30455136 DC BS EN 16035 硬件性能表 (HPS) 识别和总结测试证据 以促进建筑硬件的互换性 以应用于防火和/或防烟门和/或可打开的窗户

BS EN 16035. Hardware performance sheet (HPS). Identification and summary of test evidence to facilitate the inter-changeability of building hardware for application to fire resisting and/or smoke control doorsets and/or openable windows

T/ZJWJ 002-2022 液压地弹簧

一、该标准主要依据行业标准QB/T 2697-2013《地弹簧》,同时结合了国内外优秀同类生产企业先进产品的技术要求编制而成。标准编写结构合理、内容叙述正确、层次清晰，引用标准现行有效，符合GB/T 1.1-2020的规定。 二、该标准按照团体标准的定位和要求制定，在编制过程中广泛征求、采纳了各方的意见和建议，同时结合了液压地弹簧产业现状和发展方向，可操作性强。标准中设置的技术指标和要求均可验证、可检测，试验方法均有标准作支撑，可转化为认证实施细则。 三、该标准提出了液压地弹簧的术语和定义、技术要求、试验方法、检验规则、标志、安装说明、包装、运输和贮存，标准的主要技术指标要求达到了国内一流、国际先进水平，符合团体标准的基本要求。 与QB/T 2697-2013《地弹簧》要求相比，主要先进性体现如下： 1）提高了产品的渗漏指标，在整个性能测试过程中，地弹簧不应出现渗漏； 2）提高了产品的最大开启角度指标，扩大了产品应用领域； 3）大幅度提升了产品温度对关门时间的影响，温度最低至-40℃，扩大了产品应用领域，体现产品特色； 4）提升了产品的耐腐蚀性指标，由80%提升至90%，更符合现有产品的高质量特色。 四、该标准的制订、发布与实施将规范产品的技术要求，提升产品的市场竞争力，有利于提高产品的技术水平。

Hydraulic floor spring

T/GDSA 001-2022 石材应用护理工艺技术规范

本标准共分15章，主要内容包括：前言、范围、规范性引用文件、术语和定义、现场的勘察与工程设计、护理环境技术要求、护理材料的选择、材料进场的验收与保管使用、护理设备设施要求、测量仪器设备要求、技术人员要求、项目技术内容、项目主要环节与工艺流程、项目工艺技术指标要求、项目完成后的现场处理等。

The process standard of stone maintenance in application

GSO EN 13126-15:2022 建筑五金件 门窗和门高窗五金件 要求和测试方法 第15部分：水平滑动滚轮和滑动折叠窗五金件

This part of EN 13126 specifies requirements and test methods for durability, strength, security and function of rollers for horizontal sliding and hardware for inward or outward sliding folding windows and door height windows in accordance with common application as shown in Figures C.1 to C.7 in informative Annex C. This document is applicable to rollers irrespective of whether they are adjustable or not and irrespective of the method or type of fixing or if they are used independently, or in multiples or combinations. All components of the hardware (e.g. guide tracks, lateral guides, rails, hinges) used while testing the rollers for sliding folding windows and door height windows (window types Q, R and S) are considered to be part of the complete sliding folding hardware set.

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 15: Rollers for horizontal sliding and hardware for sliding folding windows

GSO EN 13126-8:2022 建筑五金件 窗和门高窗五金件 第8部分：倾斜和旋转、先倾斜和仅旋转五金件的要求和测试方法

This European Standard specifies the requirements and test procedures for durability, strength, security and function of Tilt and Turn, Tilt-First and Turn-Only hardware components or sets for windows and door height windows in accordance with common application as shown in informative Annex C. NOTE To maintain the guaranteed characteristics during the utilization period, the manufacturers' product information and the manufacturers' maintenance and service instructions will be complied with in a manner that can be proven.

Building hardware - Hardware for windows and door height windows - Part 8: Requirements and test methods for Tilt and Turn, Tilt-First and Turn-Only hardware

T/CECS 1066-2022 车库地坪技术规程

本规程共分7章和3个附录，主要技术内容包括：总则、术语、材料、设计、基面检查和处理、施工和验收等。

Garage Floor Technical Regulations