93.080.10 道路建筑 标准查询与下载

GB/T 30750-2014 道路施工与养护机械设备 路面处理机械 安全要求

本标准规定了路面处理机械的安全要求。本标准适用于下列路面处理机械:--沥青洒布机(又称沥青喷洒机);--石屑撒布机;--路面修复机械(即沥青喷洒石屑撒布机,又称沥青碎石同步封层机,以下简称喷洒撒布机);--沥青砂胶搅拌机;--灌缝机;--微表处/稀浆封层机。路面处理机械可安装在运输车辆、挂车或铰接式卡车上组合形成一个完整的设备。路面处理机械也可安装在其专用底盘结构和行走驱动装置(自行式或步行控制式)上。在所有的情况下,机器和底盘都形成了一个完整的设备。适用于运输卡车底盘方面的规章和标准,与本标准中称为“运输车辆”的设备相关,即使其为了应用于路面处理而做了特别修改。其在公共道路交通中的使用由相关国家法规管理。本标准涉及通过风险评估确定的路面处理机械预定使用和在制造商可预见的条件下使用时的所有重大危险(见第4章)。本标准不涉及与压力容器、噪声和电磁兼容(EMC)相关的重大危险。本标准规定了消除或减小与机器运转、设置、调整、卸载和日常维护相关的重大危险所引起风险的适当技术措施。本标准不包含对运输车辆或特殊结构的要求。这些要求包含在与运输车辆制造有关的规章中。本标准不涉及振动,因为对于此类型的所有机械,振动不是由于较低的工作速度和特定工作条件(如平坦表面)所引起的相关危险。本标准不涉及与在潜在爆炸性环境中操作机器相关的风险。本标准不包括与道路运输危险物品相关的要求。

Road construction and road maintenance machinery and equipment.Road surface treatment machines.Safety requirements

DB12/T 939-2024 国省公路涉路工程技术要求

Technical requirements for road-related projects on national and provincial highways

DB12/T 940-2024 国省公路涉路工程技术评价报告编制要求

Requirements for the preparation of technical evaluation reports for road-related projects on national and provincial highways

DB34/T 4649-2023 智慧高速公路建设指南

Smart Highway Construction Guide

T/CCTAS 78-2023 高速公路集中养护作业指南

本文件规定了集中养护作业模式一般规定、前期调查、交通组织方案、施工组织方案、工程实施、项目后评价等内容。

Operation guide for centralized maintenance of expressway

ASTM D1751-23 混凝土路面和结构施工用预制膨胀节填料（非挤压和弹性沥青类型）

Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

T/TMAC 073-2023 公路土质路堑高边坡施工监测技术规程

本文件规定了公路土质路堑高边坡施工监测的基本规定、监测方案编制、监测等级、监测项目、监测点布置、监测方法及精度要求、自动化实时监测系统要求、监测频率、监测预警和监测成果。

Technical regulations for construction monitoring of highway soil cuts and high slopes

DB3201/T 1161-2023 公路绿色工区设计技术规范

本文件主要内容包括公路绿色工区设计的术语和定义、符号及代号、绿色建筑设计与施工、能源与照明系统、暖通系统、新型雨水收集系统、污水与固废管理、生态型排（透）水道路与公路绿色工区评价。

Technical specifications for highway green work area design

T/CIC 411-2023 煤矸石集料在路面基层中应用技术指南

本文件规定了公路工程用煤矸石集料路面基层的煤矸石集料、其他原材料、混合料组成设计、施工、质量检验与控制。 本文件适用于煤矸石路面基层材料在各等级公路基层与底基层中的应用，市政道路可参照执行。

Technical Guidelines for Application of Coal Gangue Aggregate in Pavement Base

ASTM D1752-18(2023) 混凝土铺路和结构施工用预制海绵橡胶、软木和再生 PVC 膨胀缝填料的标准规范

Standard Specification for Preformed Sponge Rubber, Cork, and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction

DB4201/T 674-2023 建设工程固体废弃物堆填技术规程

Technical regulations for construction solid waste landfill

ISO/FDIS 24147:2023 道路作业机械及相关设备 路面清洁机 术语和商业规范

Road operation machinery and associated equipment — Road surface cleaning machines —Terminology and commercial specifications

DB42/T 2016-2023 土工格栅加筋土路基设计与施工技术规范

Technical specifications for design and construction of geogrid reinforced soil subgrade

GSO ISO 15645:2023 道路建设和养护设备 道路铣刨机械 术语和商业规范

This document establishes the terminology, functions, types and characteristics of road milling machinery. It is applicable to the planing of pavements made of concrete, asphalt and similar materials with a view to removing them.

Road construction and maintenance equipment — Road milling machinery — Terminology and commercial specifications

GSO ISO 15688:2023 道路建设和养护设备 土壤稳定剂 术语和商业规范

ISO 15688:2012 establishes the terminology, definitions of operation and commercial specifications for soil stabilizers and their components intended for use in road construction and pavement works. ISO 15688:2012 does not apply to soil stabilizers used in agricultural applications.

Road construction and maintenance equipment — Soil stabilizers — Terminology and commercial specifications

DB11/T 2081-2023 道路工程混凝土结构表层渗透防护技术规范

Technical specification for surface penetration protection of concrete structures in road engineering

ASTM E1890-11(2023) 验证新区域参考滑轨测量系统和设备的标准指南

1.1 This guide covers validating area reference skid measurement systems (ARSMS) and related equipment. These systems have been used since 1976 to evaluate and correlate Test Method E274/E274M skid measurement systems used primarily as a pavement management tool by state Departments of Transportation. Also, this guide provides guidelines for the revalidation process following the replacement of components within an ARSMS. 1.2 This guide is offered as a process to identify and quantify the variables that affect system performance, to minimize the effect of these variables, and to provide a method of validating a new ARSMS to replace an existing ARSMS that has provided quality correlation data for a very long time. 1.3 The values stated in inch-pound units are to be regarded as the standard since the ARSMS will be compared with state departments of transportation systems that all currently use inch-pound units. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Validating New Area Reference Skid Measurement Systems and Equipment

ASTM D2950/D2950M-22 用核子法测定现场沥青混合料密度的标准试验方法

1.1 This test method describes a test procedure for determining the density of asphalt mixtures by the attenuation of gamma radiation, where the source and detector(s) remain on the surface (backscatter method) or the source or detector is placed at a known depth up to 300 mm [12 in.] while the detector or source remains on the surface (direct transmission method). 1.2 The density, in mass per unit volume of the material under test, is determined by comparing the detected rate of gamma emissions with previously established calibration data. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 All observed and calculated values shall conform to the guide for significant digits and rounding established in Practice D6026. 1.5 For limitations, see Section 5 on Interferences. 1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. It is the recommendation of Committee D04 that the following note be added to the end of the Significance and Use section of all applicable standards. Applicable standards are those in which measurement or calibration are made, sample are procured, or products are selected. The subcommittee shall determine the appropriateness of adding the note throughout the consensus process. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 7. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Density of Asphalt Mixtures in Place by Nuclear Methods

T/EERT 029-2022 超疏水生态土路建设技术规范

本文件规定了超疏水生态土路建设的术语和定义、基本规定、设计要求、施工要求、质量控制与验收、后期维护和保养等

Technical specifications for construction of super-hydrophobic ecological soil road

ASTM D448-12(2022) 道路和桥梁施工用骨料尺寸的标准分类

1.1 This classification defines aggregate size number designations and standard size ranges for mechanical sieve analyses of coarse aggregate and screenings for use in the construction and maintenance of various types of highways and bridges. 1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. NOTE 1—Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size. 1.3 The text of this classification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the classification. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification for Sizes of Aggregate for Road and Bridge Construction