97.150 铺地非织物 标准查询与下载

24/30466842 DC BS ISO 14486 层压地板覆盖物 规格

BS ISO 14486 Laminate floor coverings - Specification

24/30474040 DC BS ISO 2025 纺织地板覆盖物 不透水性测试

BS ISO 2025 Textile floor coverings — Water impermeability test

ASTM G219-23 使用斜面测试装置测定测试偶静态摩擦系数的标准指南

1.1  This guide is intended to standardize the use of an inclined plane testing device to measure the static (breakaway) coefficient of friction between two bodies. One body is in the form of a small “rider” (few centimeters) and the other a rectangular flat plane (50 mm to 75 mm by 400 mm). The rider is placed on the plane and the plane is inclined at an angle to produce motion of the rider. The tangent of the angle at which macroscopic motion of the rider initiates on the angled plane is the breakaway or static coefficient of friction for that sliding couple. 1.2  Units— The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Determination of Static Coefficient of Friction of Test Couples Using an Inclined Plane Testing Device

24/30483342 DC BS EN 14215 纺织地板覆盖物 地毯和地毯规范

BS EN 14215 Textile floor coverings- Specification of rugs and runners

ASTM F3010-18(2024) 用于弹性地板覆盖物的双组分树脂基膜形成防潮系统的标准实施规程

1.1  This practice covers the properties, application, and performance of a two-component resin based membrane-forming moisture mitigation system to high moisture concrete substrates prior to the installation of resilient flooring. 1.2  This practice includes recommendations for the preparation of the concrete surface to receive a two-component resin based membrane-forming moisture mitigation system. 1.3  This practice does not supersede written instructions of the two-component resin based membrane-forming moisture mitigation system manufacturer, the resilient flooring manufacturer, underlayment manufacturer, the adhesive manufacturer, or other components of the finish flooring system, or combinations thereof. Users of this practice shall review manufacturer’s technical data sheets and installation instructions for compatibility of system components. 1.4  The following membrane-forming or non membrane-forming moisture mitigation systems are not included in the scope of this practice: 1.4.1  Moisture mitigation systems that chemically react with any constituent of the concrete to form a gel or crystalline substance within the concrete. 1.4.2  Penetrating, water- or solvent-based compounds that do not form a continuous membrane on the concrete surface. 1.4.3  Water-based membrane-forming moisture mitigation systems are not included in the scope of this document. 1.5  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Two-Component Resin Based Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Floor Coverings

ASTM F3041-14(2024) 信息和文档

1.1  This specification covers the requirements for the compound and physical characteristics of bonded rubber crumb floor coverings. 1.2  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Bonded Rubber Crumb Floor Coverings

ASTM D6119-19(2024) 参考资料

1.1  This practice covers the trafficking of pile yarn floor coverings in a laboratory in order to effect a change in surface appearance as a result of exposure to foot traffic under controlled conditions. A separate test method, D7330 , covers the assessment of surface appearance change using the Carpet and Rug Institute Reference Scales.2 1.2  This practice is applicable to most changes in surface appearance observed in all types of carpet that are intended for residential or commercial use. It eliminates change in appearance associated with soiling by focusing on appearance change due to matting, flattening, or change in pile fiber configuration. Although “pile reversal” or “watermarking” is occasionally visible, this practice is not a reliable method for producing this phenomenon. 1.3  This practice may be used by mutual agreement between the purchaser and supplier to set purchasing specifications. 1.4  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.Specific precautionary statements are given in Section 7 . 1.6  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Creating Surface Appearance Changes in Pile Yarn Floor Covering from Foot Traffic

ASTM D5823-19(2024) 信息技术 多媒体应用程序格式（MPEG-A） 第4部分：音乐幻灯片应用程序格式修改件2：受保护的音乐幻灯片应用程序格式的一致性和参考软件

1.1  This test method covers the determination of tuft height using a grooved specimen holder. It applies to cut-pile and loop-pile floor covering after adhesive backing has been applied to bond the pile yarn to the backing fabric. 1.2  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Tuft Height of Pile Floor Coverings

ASTM D6859-18(2024) 信息技术 视听对象编码 第5部分：参考软件 修改件10：SSC、DST、ALS 和 SLS 参考软件

1.1  This test method covers the determination of pile thickness of finished level pile yarn floor covering using a thickness measuring instrument having a stationary surface (platen), a circular pressure foot under specified force, and capable of being moved vertically above the platen. 1.2  This test method is applicable only to finished level loop, cutpile and cut & loop constructions with tuft heights less than 0.25 in. (6 mm). 1.3  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Pile Thickness of Finished Level Pile Yarn Floor Coverings

ASTM D6962-24 绒线地板覆盖物用滚筒椅试验机操作的标准实施规程

Standard Practice for Operation of a Roller Chair Tester for Pile Yarn Floor Coverings

ASTM D5252-24 六足翻转滚筒试验机操作的标准实施规程

Standard Practice for the Operation of the Hexapod Tumble Drum Tester

ASTM D6540-24 绒线地板覆盖物加速腐蚀的标准试验方法

Standard Test Method for Accelerated Soiling of Pile Yarn Floor Covering

ASTM F1914-18(2023) 弹性地板覆盖物的短期压痕和残余压痕的标准试验方法

Standard Test Methods for Short-Term Indentation and Residual Indentation of Resilient Floor Covering

ASTM F1066-23 乙烯基复合地砖标准规范

Standard Specification for Vinyl Composition Floor Tile

CAN/CGSB-4.2 No. 27.6-2023 纺织品测试方法 软地板覆盖物的阻燃性

1 Scope This National Standard of Canada: • determines the flame resistance of soft floor coverings when exposed to an ignition source (methenamine for timed burning tablet) under specified conditions; • establishes sampling plans and procedures to determine the acceptability with respect to the flame resistance of soft floor coverings using a sequential sampling procedure; • describes a procedure for the removal, prior to testing for flame resistance, of non-permanent flame-retardant treatments applied to soft floor coverings. It is applicable to all types of soft floor coverings, regardless of fibre type or method of construction. The testing and evaluation of a product against this standard may require the use of materials and/or equipment that could be hazardous. This standard does not purport to address all the safety aspects associated with its use. Anyone using this standard has the responsibility to consult the appropriate authorities and to establish appropriate health and safety practices in conjunction with any applicable regulatory requirements prior to its use. Units of measurement – Quantities and dimensions used in this standard are provided in units from the International System of Units (imperial equivalents may be shown in brackets). Exceptions may be permitted.

Textile test methods Flame resistance of soft floor coverings

CAN/CGSB-4.2 Nº 27.6-2023 纺织品测试方法 软地板覆盖物的阻燃性

1 Objet La présente Norme nationale du Canada : • permet de déterminer la résistance à l’inflammation des revêtements de sol mous lorsqu’ils sont exposés à une source d’allumage (tablette de méthénamine à durée de combustion déterminée) dans des conditions précises; • établit des procédures et des plans d’échantillonnage pour déterminer l’acceptabilité en ce qui a trait à la résistance à l’inflammation des revêtements de sol mous au moyen d’un plan d’échantillonnage progressif; • décrit une procédure pour la suppression, avant l’essai de résistance à l’inflammation, des traitements ignifuges non permanents appliqués aux revêtements de sol mous. Elle s’applique à tous les types de revêtements de sol mous, sans égard au type de fibre ou au procédé utilisé pour leur fabrication. La mise à l’essai et l’évaluation d’un produit selon la présente norme peuvent nécessiter l’emploi de matériaux et/ou d’équipement susceptibles d’être dangereux. La présente norme ne traite pas de tous les aspects liés à la sécurité de son utilisation. Il appartient à l’usager de la présente norme de se renseigner auprès des autorités compétentes et d’adopter des pratiques de santé et sécurité conformes aux règlements applicables avant de l’utiliser. Unités de mesure – Les grandeurs et les dimensions indiquées dans la présente norme sont exprimées en unités du Système international d’unités (les unités anglo-saxonnes équivalentes peuvent être indiquées entre parenthèses). Des exceptions peuvent être permises.

Textile testing methods Flame resistance of soft floor coverings

ASTM E648-23 使用辐射热能源的地板覆盖系统临界辐射通量的标准试验方法

Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source

ISO/CD 23122:2023 纺织地板覆盖物 通过六足转鼓测试仪产生外观变化

Textile floor coverings — Production of changes in appearance by means of hexapod tumbler tester

ASTM D6333-23 从地板上收集可分解农药残留物的标准实施规程

Standard Practice for Collection of Dislodgeable Pesticide Residues from Floors

ISO/CD 20251:2023 纺织地板覆盖物 - 不透水性测试

Textile floor coverings — Water impermeability test