关键字：
板材, HPL,
人造装饰板, EN
438-2, BS EN
438-4,
Artificial Decorative plates,
层压板, BS EN 438-3, BS EN 438, GB/T 17657, 密度板测试, EN 622, 纤维板测试, 胶合板测试, 甲醛测试, SGS, GB/T 15102, AS 2269, ANSI NEMA LD 3, AS/NZS 2269, SGS厦门, 厦门SGS, 装饰板检测, 人造板测试
SGS专业实验室提供人造装饰板Artificial Decorative plates测试服务
针对Wood-based Panels 木基板材（欧盟EN标准）常规测试项目：弯曲强度Bending strength, 弯曲弹性模量Modulus of in bending, 胶合板剪切强度, 浸水后厚度膨胀率Swelling in thickness after immersion in water, 垂直板面抗拉强度Tensile strength perpendicular to the plane of the board, 含水率moisture content, 密度Density, 长度, 宽度和厚度Length, Width and thickness, 方正度和边直度Squareness and Straightness
人造装饰板Artificial Decorative plates相关产品规范：
EN 438-2:2005 High-pressure decorative laminates (HPL)-Sheets based on thermosetting resins (usually called Laminates)-Part 2: Determination of properties
装饰用高压层压制件(HPL).热固性树脂为基质的板材.第2部分:性能测试
Assessment of appearance外观评价, Determination of thickness厚度, Determination of length and width长宽, Determination of edge straightness边直线度, Determination of edge squareness边直角度, Resistance to surface wear表面耐磨测试, Resistance to abrasion耐磨测试, Resistance to Immersion in Boiling Water耐沸水浸泡, Substrate protection against water vapour基材耐水蒸汽保护, Resistance to water vapour耐水蒸汽, Resistance to wet conditions耐湿测试, Resistance to dry heat耐干热, Dimensional stability at elevated temperature高温尺寸稳定性, Resistance to climatic shock耐环境温湿变化测试, Resistance to impact by small-diameter ball耐小球冲击, Resistance to impact by large-diameter ball耐大球冲击, Resistance to impact by large-diameter ball耐大球冲击, Resistance to cracking under stress耐应力开裂(层压板厚度≤2mm), Resistance to crazing (Compact laminates) 耐龟裂, Resistance to scratching 耐刮痕, Resistance to staining 耐污性, Light resistance(Xenon arc)耐光色牢度(氙弧灯), Resistance to UV light (Exterior grade laminates)耐紫外光(适于外用级层压板), Resistance to artificial weathering(including light fastness)耐人工气候老化(包括光照色牢度), Resistance to cigarette burns耐香烟燃烧, Formability(Method A)可成型性(方法A), Resistance to blistering(Method A)耐起泡(方法A)
EN 438-6:2005 High-pressure decorative laminates (HPL)-Sheets based on thermosetting resins (usually called Laminates)- Part 6: Classification and specifications for Exterior-grade Compact laminates of thickness 2 mm and greater
EN 438-6:2005 装饰用高压层压制件(HPL).热固性树脂为基质的板材.第6部分:等于和大于2mm厚的外部用压实层压板材的分类和规范
Flexural modulus弯曲模量, Flexural strength弯曲强度, Tensile strength拉伸强度, Density密度, Resistance to impact by large diameter ball（shatter resistance)耐落球(大直径落球)冲击测试, Resistance to wet conditions耐湿测试, Dimensional stability at elevated temperature 高温尺寸稳定性, Resistance to climatic shock耐环境温湿变化测试, Resistance to UV light (Exterior grade laminates)耐紫外光（适于外用级层压板）, Resistance to artificial weathering(including light fastness)耐人工气候老化(包括光照色牢度), Requirement for reaction to fire防火性能要求
BS EN 438-4:2005 High-pressure decorative laminates(HPL) — Sheets based on thermosetting resins (Usually called Laminates) —Part 4: Classification and specifications for Compact laminates of thickness 2 mm and greater
装饰用高压层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第4部分:厚度为2毫米和大于2毫米的压实层压制件的分类和规范
Inspection requirements 外观检查, Determination of thickness厚度, Determination of length and width长宽, Determination of edge straightness边直线度, Determination of edge squareness边直角度, Determination of flatness平整度, Resistance to surface wear表面耐磨性能, Resistance to impact by largediameter ball (optional)耐落球(大直径)冲击, Resistance to scratching耐刮擦, Resistance to dry heat 耐高温干热(180°C), Resistance to wet heat (100°C)耐高温湿热, Resistance to staining耐污染, Light fastness (xenon arc)耐光性能, Resistance to water vapour耐水蒸气, Resistance to cigarette burns 耐香烟燃烧, Resistance to crazing耐龟裂, Flexural modulus /Flexural Strenth 弯曲模量/弯曲强度, Tensile strength 拉伸强度, Density密度, Reaction to fire防火性能, Spread of flame火焰传播
其它产品规范如：
BS EN 438-3:2005 High-pressure decorative laminates (HPL) — Sheets based on thermosetting resins (Usually called laminates) —Part 3: Classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates
装饰用高压层压制件(HPL).基于热固性树脂的薄板材(通常称为层压制件).第3部分:用于粘结支撑基质的不足2毫米厚的层压制件的分类和规范
GB/T 17657-2013 人造板及饰面板理化性能试验方法
Test methods of evaluating the properties of wood-based panels and surface decorated wood-based panels
AS 6669 Plywood-formwork
胶合板-模板
AS 2269.0 Plywood-Structure Part.0 specifications
胶合板-结构 第0部分：规范
AS/NZS 2269.1:2012 Plywood-Structure Part.1 Test methods
胶合板—结构 第1部分：测试方法
ANSI NEMA LD 3-2005 High-Pressure Decorative Laminates
高压装饰层压板
GB/T 15102-2006 浸渍胶膜纸饰面人造板
Surface decorated wood-based panels with paper impregnated thermosetting resins
EN 622-1:2003 Fibreboards - Specifications - Part 1: General requirements
纤维板—规范—第一部分：一般要求
EN 622-2 Fibreboards - Specifications - Part 2: Requirements for hardboards
纤维板—规范—第二部分：硬木板的要求
EN 622-3 Fibreboards - Specifications - Part 3: Requirements for medium boards
纤维板—规范—第三部分：中密度板的要求
SGS提供的服务非常广泛，包括检验、测试、产品认证、工厂审核、体系认证、贸易保障等。若您所检测项目或其他认证、检验等服务没有在列在上面，请和我们联系咨询，我们可根据标准或客户要求，提供相关服务。
详情请垂询：
SGS通标标准技术服务有限公司
福建省厦门市火炬（翔安）产业区翔虹路31号
郭女士（Nicky Guo）
联系电话（Tel）：+86-0592-5766954(直线)
移动电话（Mobile)：18650803319
邮箱E-Mail：
Nicky.guo@sgs.com
关于SGS
SGS 是全球领先的检验、鉴定、测试和认证机构。 我们是全球公认的质量和诚信基准。 80,000多名员工在全球运作1,650 多个分支机构和实验室。
