Reliance液相色谱自动进样器

常规指标：

Sample Viscosity 0.3 - 5 cP, user selectable for optimized cycle times. 样品粘度：0.3 - 5 cP，用户可选择，优化进样循环时间

Sample Capacity 1 plate in autosampler, max. 24 shallow or 12 deep well plates in stacker. 自动进样器上一个样品盘，架子上zei多24个浅孔板或12个深孔板

Plate types 48-vial plates, 96 shallow well, 96 deep well,384 shallow well or user defined well plate.样品盘位：48位，或96浅孔、96深孔、384浅孔或用户定义的样品盘

Vial Dimensions Max. height vials: 47 mm (incl. cap); min. height vials: 12.5 mm (incl. cap). Note: select plate type in properties (Sparklink™). Only rigid plate material.

6x8 vials, dimensions base plate 

128 x 85.8 mm (optional). 

Loop环体积：5-1000 µL. 

Plate & Height Detection Missing plate & height detection by vial sensor. 

Wash Solvent 3 Solvents selectable on Syringe Dispenser Valve. 

分析性能：

Capped and sealed vials/plates: 带盖和密封的样品瓶

• Full Loop Injections Reproducibility: RSD ≤ 0.3 %. 全环进样重现性：RSD ≤ 0.3 %. 

• Partial Loopfill Injections Reproducibility: RSD ≤ 0.5 %, injection volumes > 5 µL, with headspace pressure on the vial and 30 µL pre-flush with air segment. 

   半环进样重现性：RSD ≤ 0.5 %,进样体积：> 5 µL，样品瓶上带顶空压力，30 µL预清洗带空气部分

• Zero sample loss Injections Reproducibility: RSD ≤ 1.0 %, injection volumes > 5 µL,with headspace pressure on the vial. 

  零样品丢失进样重现性：RSD ≤ 1.0 %，进样体积：> 5 µL，样品瓶上带顶空压力

Open vials/plates, valid at 1.0 cP: 开口的样品瓶

• Full Loop Injections Reproducibility: RSD ≤ 0.3 %.全环进样重现性：RSD ≤ 0.3 %. 

• Partial Loopfill Injections Reproducibility: RSD ≤ 0.5 %; injection volumes > 5 µL,without headspace pressure on the vial and 30 µL pre-flush with air segment. 

  半环进样重现性：RSD ≤ 0.5 %,进样体积：> 5 µL，样品瓶上不带顶空压力，30 µL预清洗带空气部分

• Zero sample loss Injections Reproducibility: RSD ≤1.0 %; injection volumes > 5 µL.without headspace pressure on the vial.

  零样品丢失进样重现性：RSD ≤ 1.0 %，进样体积：> 5 µL，样品瓶上不带顶空压力

Carry-over < 0.01 % with programmable needle wash. 交叉残留：< 0.01 %，带可编程的针清洗

Method programming 方法编程

Injection Methods • Full loop injections • Partial loopfill injections • Zero sample loss injections. 

Injection Modes • Speed mode • Flex mode. 

Injection Volumes 

Injections per Vial Max. 9 (volumes are programmable for each injection). 每个样品瓶进样体积：zei大9（每次进样体积可编程）

Analysis Time Max. 9 hrs. 59 min. 59 sec. 分析时间：zei大9小时59分钟59秒

Needle Wash Volume Programmable 700-9999 µL, with 3 solvents.可编程的针清洗体积：700-9999 µL, 带3种溶剂

选项：

Temperature Control：

  Built-in Peltier cooling in autosampler and stacker.

  Closed conditioned system for guaranteed constant temperature and humidity suitable for 24-hour operation. Temperature is software programmable

  (Sparklink™) and computer-monitored. 

Integrated Column Switching (ISS) ：Integrated high pressure stream switching valve. 

Biocompatible Option： Rheodyne or Valco biocompatible valves, with PEEK sample needle and PEEK flowpath. 

Biocompatible Column Switching Valve ISS：

  Mistral column oven combined with the Reliance™. 

  The injection valve and optional column switching valve fit into the column oven.

Bio-needle： Specially designed sample needle for easier sampling of serum, plasma and urine samples.