This document specifies the mechanical and physical properties of bolts, screws, s tuds and nuts, with coarse pitch thread and fine pitch thread, made of corrosion-resistant stainless s teels (i.e. martensitic stainless steels and precipitation hardening aus tenitic stainless steels) and nickel alloys, intended for use at high temperatures up to 800 °C . Tests in accordance with Clause 9 are performed at the ambient temperature range of 10 °C to 35 °C , and other tes ts can be performed at higher temperatures, see Clause 10. NO TE Fas teners specified in this document are also suitable when used at low temperatures, typically down to -50 °C . For more information, see ISO 3506 - 6 . The term “fasteners” is used in this document when bolts, screws, s tuds and nuts are considered all together. nickel alloys as well as their properties . This document applies to fasteners: — with ISO metric thread in accordance with ISO 68-1 , — with diameter/pitch combinations in accordance with ISO 261 and ISO 262 , — with coarse pitch thread M3 to M39, and fine pitch thread M8×1 to M39×3 , — with thread tolerances in accordance with ISO 965-1 and ISO 965-2 , and — of any shape but with full loadability. Stainless steel and nickel alloy fas tener s ymbols can be used for sizes outside the diameter limits of this document (i.e. for bolts, screws and s tuds with d < 3 mm or d > 39 mm and for nuts with D < 5 mm or D > 39 mm) , provided that all applicable chemical, mechanical and physical requirements are met. Fas teners with reduced loadability (i.e. thin nuts and bolts, screws and studs with head or unthreaded shank weaker than the threaded shank) are not dealt with in this document. This document does not specify requirements for functional properties such as: — torque/clamp force properties, — shear s trength, — fatigue resistance, — weldability, 1 or — properties ofbolted joints and fasteners in high temperature environment (see test methods at high temperature for fasteners in Clause 10).
ISO 3506-5:2022由国际标准化组织 IX-ISO 发布于 2022-04-29。
ISO 3506-5:2022在国际标准分类中归属于: 21.060.99 其他紧固件。
* 在 ISO 3506-5:2022 发布之后有更新,请注意新发布标准的变化。
一些ISO 和ASTM 标准,如EN ISO898,ASTM F2328M或ASTM El077,ASTM F606/M和ISO 3887,都对硬度测试的方法进行了说明。本文将重点介绍黑色金属材料的一些硬度测试要求,以及评估紧固件的备选方法,包括如何对有色金属材料进行测试评估。对于黑色金属材料对不同区域进行测试,如图1所示,该方法可以确定母材金属区域的高度(E)和部分脱碳区/渗碳区的检测(2)。...
锌镍合金特点:1.沉积速度快 ,有较好的可焊性 ,镀层镍含量可稳定地控制,镀液具有良好的整平性能,镀层呈银白色高光亮。 2.优异的耐腐蚀性,比锌层高3倍以上经彩色钝化或黑色钝化,耐蚀性将大大提高。同样厚度时,锌镍合金层耐腐蚀性为纯锌镀层的4-8倍,镀层本身对钢铁基体为阳极性镀层,可提供有效的阴极保护作用。锌镍合金镀层的硬度比纯锌高,因而具有更好的耐磨性。 ...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号