SAE ARP743C-2010
通过手动颗粒计数法测定粉尘控制空间中空气颗粒污染的程序
Procedure for the Determination of Particulate Contamination of Air in Dust Controlled Spaces by the Manual Particle Count Method
2010-05
购买全文，请联系:
- 标准号
- SAE ARP743C-2010
- 发布
- 2010年
- 发布单位
- SAE - SAE International
- 当前最新
- SAE ARP743C-2010
- 适用范围
- "This SAE Aerospace Recommended Practice (ARP) describes two procedures for sampling particles in dust controlled spaces. One procedure covers airborne dust above 5 ?m. The other (and newly added procedure) covers particles of 25 ?m and larger that ""fall out"" of the environment onto surfaces. In each case the particles are sized in the longest dimension and counted. Airborne particles are reported as particles per cubic meter (cubic foot) whereas particles collected in fall out samples are reported as particles per 0.1 square meter (square foot). This document includes English units in parentheses as referenced information to the SI units where meaningful. These procedures may also be used for environmental analysis where the quality of the particles by visual or chemical analysis is intended. Field of Application: Airborne particle sampling (volumetric samples) - This procedure may be used in lieu of automatic particle counters for verifying conformance with FED-STD-209 for cleanroom classes above 10@000 unless the user or contracting agency specifies the counting of 0.5 ?m particles. It may also be used for environmental analysis where the quality of the particles by visual identification is desirable. This procedure can be used as a rough correlation check of particles greater than 5 ?m when calibrating automatic particle counters. Limitations and Errors: This procedure is a slower alternative to the method by automatic particle counter@ but necessary when the identification of particles is a concern. This procedure is not appropriate when particles below 5 ?m are of concern. The procedures herein are not recommended to evaluate the residues that may collect on residue sensitive instruments such as optics and sensors. These residues@ sometimes called non-volatile residue (NVR) or volatile condensable material (VCM) are best sampled by other means. One source of error in these procedures is a poor distribution of particles on the membrane filter surface (see.3.8.6) while another is from errors occurring during the microscopic analysis."
SAE ARP743C-2010相似标准
推荐
化学药品粒度、纤维长度和粒径分布检测指南
4.4电阻法（如库尔特法）（见OECD 110）适用范围：干燥的粉末/颗粒粒径范围：1-1000μm库尔特计数技术测定悬浮在电解液中的样品，当颗粒随电解液通过小孔管时，电导率发生变化，从而测定出颗粒大小。这其中一个重要的参数是颗粒在电解液中的沉降速度，而该沉降速度这取决于颗粒的密度和直径。所以密度不同的颗粒可以通过此法测定。但是，库尔特计数电阻法仅适用于流体中完全电绝缘体的粒子。...
尘埃粒子计数器工厂的应用及注意事项
尘埃粒子计数器工厂通常用于特定工业、制药厂和医疗机构的清洁空间中，以监测空气中的颗粒物和污染物，例如灰尘、霉菌孢子、碎片、挥发性有机化合物，甚至特定环境中的浮游细菌。 它还可用于商业建筑或特殊建筑物的公共空间，以确保洁净空气不受污染。 尘埃粒子计数器工厂是洁净室无尘车间空气中粉尘颗粒浓度和粒径的专用测量仪器。...
如何区别粉尘检测仪和粒子计数器
2通道分类，计算误差大于50%)，因此颗粒计数测量只能在相对干净的空间内进行，如使用粉尘浓度测量仪，误差很大。...
粉尘浓度检测仪主要用于检测环境中的粉尘浓度
粉尘浓度检测仪要用于工矿企业中粉尘颗粒物（PM10，或PM2.5或TSP）的浓度检测及超标报警。粉尘浓度检测仪将大型公共场所室内，工矿企业，工厂车间或生产车间内带有粉尘颗粒的空气吸入仪表内，通过高精度的激光粉尘检测传感器来进行分析，得出来的数据通过仪表的显示屏来显示出该空间内粉尘的浓度值。 粉尘浓度检测仪采用先进的光散射原理以半导体激光为测量光源，对空气中粉尘进行高灵敏非接触测量。...