GSO ISO 10816-2:2013
机械振动 通过非旋转部件测量评估机器振动 第2部分:正常运行速度为 1500 r/min、1800 r/min、3000 r/min、3600 r/min 的超过 50 MW 的汽轮机和发电机

Mechanical vibration -- Evaluation of machine vibration by measurements on non-rotating parts -- Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min


 

 

非常抱歉,我们暂时无法提供预览,您可以试试: 免费下载 GSO ISO 10816-2:2013 前三页,或者稍后再访问。

您也可以尝试购买此标准,
点击右侧 “立即购买” 按钮开始采购(由第三方提供)。

 

标准号
GSO ISO 10816-2:2013
发布
2013年
发布单位
GSO
当前最新
GSO ISO 10816-2:2013
 
 
适用范围
This part of ISO 10816 establishes provisions for evaluating the severity of in-situ, broad-band vibration measured radial (i.e. transverse) to the shaft axis on all main bearing housings or pedestals and in the axial direction on thrust bearings. These are in terms of: — vibration under normal steady-state operating conditions; — vibration during other (non-steady-state) conditions when transient changes are taking place, including run up or run down, initial loading and load changes; — changes in vibration which can occur during normal steady-state operation. This part of ISO 10816 is applicable to land-based steam turbines and generators with power outputs greater than 50 MW and a normal operating speed of 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min. It is also applicable to steam turbines and/or generators which are directly coupled to a gas turbine (such as for combined-cycle applications). In such cases, the criteria of this part of ISO 10816 apply only to the steam turbine and the generator (including synchronizing clutches). ISO 7919-4 and ISO 10816-4 are applicable to the evaluation of the gas turbine vibration. The evaluation criteria in this part of ISO 10816 are not applicable to the electromagnetic excited vibration with twice line frequency at the generator stator core and housing. The numerical values specified are not intended to serve as the only basis for judging the severity of vibration. For large steam turbines and generators, it is also common to judge the vibration based on measurements taken on the rotating shafts. For such vibration measurement requirements, see ISO 7919-1 and ISO 7919-2.

GSO ISO 10816-2:2013相似标准


推荐

离心机-详细离心机相关情况

离心力(g)转速(rpm)之间换算离心力G转速RPM之间换算其换算公式如下:G=1.11×10^(-5)×R×(rpm)^2其中,G离心力,一般以g(重力加速度倍数来表示。10^(-5) 即10负五次方,(rpm)^2转速平方,R半径,单位厘米。...

电机振动值标准是什么

注:无底脚电机、上脚式电机或任何立式电机,是以同一机座带底脚卧式电机(IMB3)中心高作为其中心高。2引用标准GB2298机械振动冲击名词术语3测量值对转速600~3600r/min电机,稳态运行时采用振动速度有效值表示,其单位mm/s;对转速低于600r/min电机,则采用位移振幅值(双幅值)表示,其单位mm。...

离心机转速 gr/min 间怎么换算

离心力G转速RPM之间换算其换算公式如下:G=1.11×10^(-5)×R×(rpm)^2其中,G离心力,一般以g(重力加速度倍数来表示。10^(-5) 即10负五次方,(rpm)^2转速平方,R半径,单位厘米。...

风机振动速度传感器CD33

技术参数:   1测量范围:50~10000r/min (60 齿)   2输出波形:正弦波(≥50r/min时)   3输出幅值:50r/min时≥300mV   4工作温度:-10℃~120℃   5接线方式:两线制(无源)   6螺纹规格:M16×1×80mm   7齿轮规格:模数≥2(渐开线齿轮)   8安装间隙:0.5~2mm   9重 量:约 120g...





Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号