PREN 15001-1-2017 气体基础设施 工业装置工作压力大于 0 5 bar 和工业和非工业装置工作压力大于 5 bar 的气体安装管道 第1部分:设计 材料的详细功能要求
Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0@5 bar for industrial installations and greater than 5 bar for industrial and nonindustrial installations - Part 1: Detailed functional requirements for design@ materi
This European Standard specifies detailed functional requirements for the design@ selection of materials@ construction@ inspection and testing of: ?? industrial gas installation pipework and assemblies with an operating pressure greater than 0@5 bar; and ?? non-industrial gas installation pipework (residential and commercial) with an operating pressure greater than 5 bar in buildings; starting from the outlet of the network operator??s point of delivery up to the inlet connection to the gas appliance; normally the inlet isolation valve. This standard also covers the pipework to the inlet connection of a gas appliance that is not included within the scope of the appliance standard. NOTE 1 The use of the term installation and pipework is interchangeable. Apart from the exceptions stated below@ this standard applies to gas installations operating at ambient temperatures between ?20 ??and 40 ??and operating pressures up to and including 60 bar. For operating conditions outside these limitations@ reference should additionally be made to EN 13480 (all parts) for metallic pipework. For industrial gas installations up to and including 0@5 bar and for non-industrial (residential and commercial) gas installations up to and including 5 bar in buildings@ EN 1775 applies. For gas installations that do not fall within the scope of EN 1775 or other European Standards@ this standard applies. In this European Standard@ the term ??gas?? refers to combustible gases@ which are gaseous at 15 ??and 1 013 mbar absolute atmospheric pressure (normal conditions). These gases are commonly referred to as manufactured gas@ natural gas or Liquefied Petroleum Gas (LPG). They are also referred to as first@ second or third family gases as classified in EN 437:2003+A1:2009@ Table 1. The given values are considered as normal conditions for all volumes given in this standard. This European Standard is applicable to installation pipework for the carriage of: ?? processed@ non-toxic and non-corrosive natural gas according to EN 437:2003+A1:2009 and EN 16726 ??Gas infrastructure - Quality of gas - Group H??; ?? vaporized LPG; ?? biomethane@ complying with EN 16723-1; ?? vaporized LNG. NOTE 2 The specification of vaporized LNG is equal to that of natural gas as classified in EN 437:2003+A1:2009. This European Standard does not cover pipework for hydrogen rich gases that fall outside the definitions within EN 437:2003+A1:2009. LPG storage vessels (including all ancillaries fitted directly to storage vessels) are excluded. Also excluded are LPG installations and sections of LPG installations operating at vapour pressure in the liquid state (e.g. between the storage vessel and any pressure regulator). In this standard@ all pressures are gauge pressures unless otherwise stated. This standard has been harmonized to address the essential safety requirements of the Pressure Equipment Directive (PED@ 2014/68/EU [formerly 97/23/EC]) relevant for the joining of gas installation pipework (assemblies) falling within the scope of the PED. These are listed in Annex ZA. However@ ??this Directive does not cover the assembly of pressure equipment on the site and under the responsibility of the user@ as in the case of industrial installations?? (PED@ Preamble@ 7th recital@ last paragraph). Although in this respect@ the standard takes into account the essential safety requirements of the PED@ no inference can be drawn from this as to whether or not the installation or parts of the installation falls within the scope of the PED. Reference should therefore be made to the PED and relevant national legislation. This European Standard specifies common basic principles for gas supply systems. Users of this European Standard should be aware that more detailed national standards and/or code of practice may exist in the CEN member countries. This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles. In the event of conflicts in terms of more restrictive requirements in national legislation egulation with the requirements of this standard@ the national legislation egulation takes precedence as illustrated in CEN/TR 13737-1 and CEN/TR 13737-2. This provision does not apply to requirements that are harmonized to directive 2014/68/EU (see Annex ZA). CEN/TR 13737-1 and CEN/TR 13737-2 give: ?? clarification of all legislations egulations applicable in a country; ?? if appropriate@ more restrictive national requirements thereof; ?? a national contact point for the latest information. Functional requirements for commissioning@ operation and maintenance of industrial gas installations and assemblies with an operating pressure greater than 0@5 bar and of gas installations greater than 5 bar in buildings and areas intended for non-industrial installations greater than 5 bar are described in EN 15001-2. Generally@ additional safety precautions may be necessary where non-odorized gas is used. For nonindustrial purposes@ the gas should be odorized.