IEC 61230-2008
带电作业.便携式接地或接地并短路设备
Live working - Portable equipment for earthing or earthing and short-circuiting
IEC 61230-2008 发布历史
This International Standard is applicable to portable equipment, with or without matching connection points, for temporary earthing or earthing and short-circuiting of electrically isolated or de-energized a.c. and d.c. installations, distribution and transmission networks, whether they are overhead or underground or of low or high voltage. NOTE Annex A provides guidance for application to railway systems. This standard covers equipment comprising an earthing or a short-circuiting or an earthing and short-circuiting device and insulating component. An example is given in Figure la and Figure lb. It also covers: - earthing or short-circuiting or earthing and short-circuiting devices intended to be installed with insulating means. An example of an earthing device is given in Figure lc; - separate components, such as conductive extension (see Figure lb) or clamp or cable with end fittings. The performance of equipment, devices and components covered by this standard is based on electro-dynamic and electro-thermal effects acting during short-circuit. The withstand capability of the devices and equipment is expressed by their rated values of current, time and peak factor. No rated voltage is given, but the geometrical dimensions of the equipment are also linked to the voltage of the installation. Examples of connection diagrams of earthing and short-circuiting devices are given in Figures 2 and 3. Associated usual lengths of cables are given in Table 1. Not covered in this standard are: - insulating means, such as insulating sticks, telescopic sticks, insulating handles, insulating gloves, aerial devices with insulating booms, insulating ropes to be used to install the earthing and short-circuiting device; - insulating components, except for basic safety requirements for the insulating element; NOTE Basic safety recommendations for earthing sticks are given in Annex B. - devices meant only for the draining of induced currents; - relevant working procedures for using portable equipment for earthing or earthing and short-circuiting. NOTE The equipment complying with this standard should be used according to safe working procedures and according to local or national regulation, such as live working or dead working procedures.
IEC 61230-2008由国际电工委员会 IX-IEC 发布于 2008-07。
IEC 61230-2008 在中国标准分类中归属于: K47 输电线路器材，在国际标准分类中归属于: 13.260 电击防护。
IEC 61230-2008 发布之时，引用了标准
- IEC 60060-1-1989 高压试验技术 第1部分:一般定义和试验要求
- IEC 60068-2-11-1981 基本环境试验规程 第2-11部分:试验 试验Ka:盐雾
- IEC 60068-2-42-2003 环境试验.第2-42部分:试验.试验Kc:触点和连接件的二氧化硫试验
- IEC 60811-1-4-1985 电缆绝缘和护套材料的通用试验方法 第1部分:一般使用的方法 第4节:低温试验
- IEC 60811-1-4 AMD 1-1993 电缆绝缘和护套材料的通用试验方法.第1部分:一般使用的方法.第4节:低温试验.修改件1
- IEC 60811-1-4 AMD 2-2001 电缆绝缘和护套材料的通用试验方法 第1部分:一般使用的方法 第4节:低温试验 修改2
- IEC 60811-2-1-1998 电缆和光缆用绝缘和护套材料 通用试验方法 第2-1部分:弹性化合物专用方法 耐臭氧试验、热凝固试验和矿物油浸入试验
- IEC 60811-2-1 AMD 1-2001 电缆和光缆用绝缘和护套材料 通用试验方法 第2-1部分:弹性化合物专用方法 耐臭氧试验、热凝固试验和矿物油浸入试验 修改1
- IEC 60811-3-1-1985 电缆绝缘和护套材料的通用试验方法 第3部分:聚氯乙烯(PVC)化合物专用方法 第1节:高温下压力试验 耐裂试验
- IEC 60811-3-1 AMD 1-1994 电缆绝缘和护套材料的通用试验方法 第3部分:聚氯乙稀(PVC)化合物专用方法 第1节:高温下压力试验 耐裂试验 修改1`
- IEC 60811-3-1 AMD 2-2001 电缆绝缘和护套材料的通用试验方法 第3部分:聚氯乙烯(PVC)化合物专用方法 第1节:高温下压力试验 耐裂试验 修改2
- IEC 61138-2007 便携式接地和短路设备用电缆
IEC 61230-2008的历代版本如下：
- 1993年08月 IEC 61230-1993 带电作业 便携式接地或接地并短路设备
- 2008年07月 IEC 61230-2008 带电作业.便携式接地或接地并短路设备
- 标准号
- IEC 61230-2008
- 发布日期
- 2008年07月
- 实施日期
- 废止日期
- 无
- 中国标准分类号
- K47
- 国际标准分类号
- 13.260
- 发布单位
- IX-IEC
- 引用标准
- IEC 60060-1-1989 IEC 60068-2-11-1981 IEC 60068-2-42-2003 IEC 60811-1-4-1985 IEC 60811-1-4 AMD 1-1993 IEC 60811-1-4 AMD 2-2001 IEC 60811-2-1-1998 IEC 60811-2-1 AMD 1-2001 IEC 60811-3-1-1985 IEC 60811-3-1 AMD 1-1994 IEC 60811-3-1 AMD 2-2001 IEC 61138-2007 I
- 被代替标准
- IEC 78/741/FDIS-2008 IEC 61230-1993 IEC 61230 Corrigendum 1-1999 IEC 61230 Corrigendum 2-2000 IEC 61230 Corrigendum 3-2000
- 适用范围
- This International Standard is applicable to portable equipment, with or without matching connection points, for temporary earthing or earthing and short-circuiting of electrically isolated or de-energized a.c. and d.c. installations, distribution and transmission networks, whether they are overhead or underground or of low or high voltage. NOTE Annex A provides guidance for application to railway systems. This standard covers equipment comprising an earthing or a short-circuiting or an earthing and short-circuiting device and insulating component. An example is given in Figure la and Figure lb. It also covers: - earthing or short-circuiting or earthing and short-circuiting devices intended to be installed with insulating means. An example of an earthing device is given in Figure lc; - separate components, such as conductive extension (see Figure lb) or clamp or cable with end fittings. The performance of equipment, devices and components covered by this standard is based on electro-dynamic and electro-thermal effects acting during short-circuit. The withstand capability of the devices and equipment is expressed by their rated values of current, time and peak factor. No rated voltage is given, but the geometrical dimensions of the equipment are also linked to the voltage of the installation. Examples of connection diagrams of earthing and short-circuiting devices are given in Figures 2 and 3. Associated usual lengths of cables are given in Table 1. Not covered in this standard are: - insulating means, such as insulating sticks, telescopic sticks, insulating handles, insulating gloves, aerial devices with insulating booms, insulating ropes to be used to install the earthing and short-circuiting device; - insulating components, except for basic safety requirements for the insulating element; NOTE Basic safety recommendations for earthing sticks are given in Annex B. - devices meant only for the draining of induced currents; - relevant working procedures for using portable equipment for earthing or earthing and short-circuiting. NOTE The equipment complying with this standard should be used according to safe working procedures and according to local or national regulation, such as live working or dead working procedures.