4.1 The purpose of this test is to obtain, by means of a specified laboratory procedure, the values of the equilibrium moisture content at higher RH levels (( 1.1 This test method specifies a laboratory procedure for the determination of the water retention curve (or moisture storage capacity) of porous building materials at very high relative humidity (RH) levels (≈ 95 to 100% RH) corresponding to the capillary moisture region of the sorption isotherm. This is achieved by using the pressure plate test apparatus. This technique was originally developed to study soil moisture content and eventually had been adapted to building construction materials.
1.2 At higher RH levels (≈ 95 to 100% RH) of the sorption isotherm (see Test Method C1498), use of climatic chamber is not an option. This technique uses overpressure to extract water out of the pore structure of porous materials until equilibrium between the moisture content in the specimens and the corresponding overpressure is achieved. Using the pressure plate extractors, equilibrium can only be reached by desorption.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1、 地基土荷载试验(静载荷试验---浅层平板载荷试验):试验前先在现场试坑中竖立载荷架,使施加的荷载通过承压板传到地层中,以便测试浅部地基应力主要影响范围内的土的力学性质,包括测定土的变形模量、地基承载力以及研究土的湿陷性质等,反映承压板下1.5~2.0倍承压板直径的范围内地基土强度、变形的综合特征。本试验适于所有土层,也是动探、静探、标贯、十字板及旁压及等测试技术进行相关分析的基准性试验。...
将钻孔弹模计移至另一测试部位,继续6、7、8三步试验。划重点04GY型孔内弹模测定器资料分析根据实测应变绘制钻孔孔壁压力和位移关系曲线。...
1、拉伸性能定义:在规定的试验温度、湿度及拉伸速度下,通过对塑料试样的纵轴方向施加拉伸载荷,使试样产生形变直至材料破坏。记录下试样破坏时的最大负荷和对应的标线间距离的变化等情况,可绘制出应力-应变曲线。影响因素:(1)试样的制备与处理拉伸试验要求做成哑铃形试样;制样方式有两种:一是用原材料制样;二是从制品上直接取样。...
对于按上述搅拌不少于2min仍无法浸润并漂浮在水面上的试样,称取20.0g试料置于不小于1000mL烧杯中,加入500mL水。并记下烧杯、试料和水的总质量。用多孔压板(不锈钢或有机玻璃)将样品压至液面以下,置于电炉上加热煮沸,并保持30min±5min。取下迅速冷却,取出多孔压板,并用水冲洗(注意总体积不超过500mL),补足500mL水,搅拌均匀,静置。将浸出液倾出至干燥的聚乙烯瓶中。...
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号