ASTM E1590-17
床垫着火试验的标准试验方法

Standard Test Method for Fire Testing of Mattresses

被代替

标准号

ASTM E1590-17

发布

2017年

发布单位

美国材料与试验协会

替代标准

ASTM E1590-22

当前最新

ASTM E1590-23

 

 

引用标准

ASTM D123 ASTM E1354 ASTM E1474 ASTM E1537 ASTM E176 ASTM E2067 ASTM E2257 ASTM E603 ASTM E691 ASTM E800 ASTM E84 IEEE/ASTM SI 10 ISO 13943 ISO 4880 ISO 9705

适用范围

5.1 This test method provides a means of measuring a variety of fire-test-response characteristics resulting from burning a test specimen, mattress or mattress with foundation. After ignition using a propane gas burner, the test specimen is permitted to burn freely under well-ventilated conditions. The most important fire-test-response characteristic measured in this test method is the rate of heat release, which quantifies the intensity of the fire generated.

5.2 The rate of heat release is measured by the principle of oxygen consumption. Annex A3 discusses the assumptions and limitations.

5.3 This test method also provides measures of other fire-test-response characteristics, including smoke obscuration (as the rate of smoke release, total smoke released, or optical density of smoke), combustion gas release (as concentrations of combustion gases), and mass loss, which are important to making decisions on fire safety.

5.4 In the majority of fires, the most important gaseous components of smoke are the carbon oxides, present in all fires. They are indicators of the toxicity of the atmosphere and of the completeness of combustion. Measurement of concentrations of carbon oxides are useful for two purposes: (1) as part of fire hazard assessment calculations and (2) to improve the accuracy of heat release measurements. Other toxic combustion gases, which are specific to certain materials, are also indicators of the toxicity of the atmosphere, but are less crucial for determining combustion completeness and are optional measures; however, fire hazard assessment often requires their measurement.

5.5 The type of ignition chosen (flaming source) is common in both accidental and intentional fires in public occupancies. The test method is thus applicable to mattresses in public occupancies. Such facilities include, but are not limited to, health-care facilities, old age convalescent and board and care homes, and college dormitories and residence halls.

5.6 One of the following three configurations is to be used in this test method:

5.6.1 Test Configuration A—A test room with the following dimensions: 3.66 by 2.44 by 2.44 m (12 by 8 by 8 ft) high.

5.6.2 Test Configuration B—A test room with the following dimensions: 3.66 by 3.05 by 2.44 m (12 by 10 by 8 ft) high.

5.6.3 Test Configuration C—An open calorimeter (or furniture calorimeter).

5.7 Rooms of other dimensions are acceptable where it has been shown that equivalent test results are obtained.

5.8 Measurements in the three test ......

沙发检测仪器，沙发疲劳试验机等家具检测仪器的介绍

不适合于与建筑物有联接之家具    三、抽屉滑轨反复疲劳试验机测试抽屉导轨滑轨用。执行标准：参考QB/T2454-1999 《家具五金 抽屉导轨要求和检验》    四、床垫耐久性试验机适用于各种弹簧软床垫测试。棕纤维床垫和软质泡沫聚合材料床垫等要参照相关标准进行。本机不适合充水床垫，充气床垫的测试。   ...

燃烧和阻燃测试常用测试标准汇总

BS 7175 – 通过闷燃和火焰点火源测试床罩和枕头的可燃性的测试方法* BS 7177 – 床垫，床垫，床单，沙发椅，床架的耐点火性能规范* BS 6807 – 评估试验方法 床垫，软垫和软垫床垫的可燃性* BS EN 597 – 床垫和软垫床位的可燃性评估*软体家具Cal TB 133 – 公共场所座位的可燃性测试ASTM E1537 – 软体家具燃烧测试BFD IX-10 – 软管家具规范（...

床垫冲击试验机

·床垫冲击试验机适用范围及功能：1.概述：本广泛应用于测试评估内置式床垫和箱式床垫的抗冲击性能。2.本机带有一个79.5 ± 1kg的压板以及一个zui大为250kg的负载。通过高度的调节可以很好的模拟现实环境对床垫的作用。也可以选择不同的冲击点。3.本机可以手动控制或者通过软件进行控制并记录分析数据结果绘制图表。数据可以保存进行长期对比。...

床垫弹簧测试仪有什么特点

　　床垫弹簧测试仪又称床垫弹簧疲劳试验机，专为床垫弹簧框架和弹簧包而设计，那么床垫弹簧测试仪有何具体特点呢? 　　1、能够测量弹簧的拉力、压力、刚度、位移及显示日期、编号等内容。 　　2、采用大规模集成电路，提高了测试精度，人机对话直观明了。 　　3、依据国家标准设计的弹簧检测专用程序，效率高、功能全、操作方便。 　　4、从机械原理和程序软件两方面考虑提高了量程的测量范围。 　　...