13.030.10 固态废物 标准查询与下载

T/NAIA 0223-2023 工业硫磺中汞含量的测定 微波消解-原子荧光光度法

本文件规定了用微波消解-原子荧光光度法测定工业硫磺中汞含量的测定方法。 本文件适用于由石油炼厂气、天然气、煤化工酸性气、焦炉气、烟气、含硫废气回收以及硫铁矿制得的工业硫磺中汞的测定。

Determination of mercury content in industrial sulfur by microwave digestion-atomic fluorescence photometry

T/ZGZS 0308-2023 废活性炭热处理再生技术规范

范围；规范性引用文件；术语和定义；总体要求；废活性炭的收集、运输和贮存要求；废活性炭的热处理再生过程；再生活性炭的质量检验；污染控制要求；环境监测要求；环境应急要求。

Technical specification for regeneration of waste activated carbon by heat treatment

DB65/T 4661-2023 陆路口岸进口矿产品疑似固体废物现场快速排查方法

Methods for rapid on-site inspection of suspected solid waste of imported mineral products at land ports

T/SDSES 009-2023 氯化钡尾渣制备硅质矿物掺合料

本文件规定了氯化钡尾渣制备硅质矿物掺合料的术语和定义、技术要求、试验方法、检验规则、出厂、交货与验收、标志、包装、运输、贮存等。 本文件适用于以氯化钡尾渣制备硅质矿物掺合料用作水泥、砂浆、蒸压加气混凝土砌块等的原材料。

Silica mineral admixture made from barium chloride tailings

DB4105/T 211-2023 农村生活垃圾分类处理技术规程

Rural domestic waste classification and treatment technical regulations

T/NMRJ 011-2023 一般工业固体废物管理指南

一般工业固体废物的一般要求和管理要求。

Guidelines for management of non-hazardous industrial solid wastes

T/NAIA 0217-2023 废活性炭中汞含量的测定 固体进样-冷原子吸收测汞仪法

本文件规定了用测汞仪直接进样对废活性炭中汞含量进行测定的方法。 本文件适用于废活性炭中汞含量进行测定，测定范围为0.2~50μg/kg。

Determination of Mercury Content in Waste Activated Carbon Solid Sample Injection-Cold Atomic Absorption Mercury Meter Method

T/CPCIF 0254-2023 海洋石油钻采废弃物源头减量化处置技术规范

本文件规定了海洋石油钻采废弃物源头减量化处置的一般要求、水基钻井废弃物的源头减量化处置技术要求、废弃水基完修井液的源头减量化处置技术要求、含油污泥的源头减量化处置技术要求。 本文件适用于海洋油气田勘探开发、生产过程中产生的水基钻井废弃物、废弃水基完修井液和含油污泥的源头减量化处置。

Technical specification for source reduction of wastes of drilling and oil extraction from offshore oilfield

ASTM E956-83(2023) 城市混合有色金属（MNM）的标准分类

1.1 This classification covers municipal mixed nonferrous metals (MNM), not source-separated, that are recovered from municipal waste destined for disposal. 1.2 The mixed nonferrous metals (MNM) have been subdivided according to processing history, nonferrous metal content, size, and moisture content. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification for Municipal Mixed Nonferrous Metals (MNM)

T/ZAEPI 013-2023 氢溴酸溶液包装容器再利用塑料桶

文件规定了氢溴酸溶液包装容器再利用塑料桶的技术要求、检测方法、出厂检验以及标志、包装、运输与贮存等要求。

Recycled Plastic Barrel for Hydrobromic Acid Solution Packaging Container

T/ACEF 078-2023 重金属污染地块土壤生态风险管控技术指南

本文件规定了重金属污染地块土壤生态风险管控的总体原则、工作流程、实施方案制定、措施选择与实施、效果评估和后期管理。

Technical guideline for ecological risk management and control of heavy metal contaminated sites

DB5301/T 86-2023 城镇生活污水处理厂污泥 土地利用污泥质量控制规范

Specifications for quality control of urban domestic sewage treatment plant sludge land use sludge

T/ZAEPI 010-2023 再生蜂窝状活性炭

本文件规定了再生蜂窝状活性炭的技术要求、检验方法、检验规则、标志、包装、运输和贮存等要求。

Regenerated honeycomb activated carbon

T/CQSES 04-2023 重庆市页岩气钻井岩屑资源化利用技术指南

为指导和规范重庆市页岩气钻井岩屑资源化利用及管理，本标准规定了页岩气钻井岩屑资源化利用过程中一般要求，并对减量化技术、废油回收利用技术、建材利用技术的技术指标、产品质量及环境保护、污染防治提出要求，对有效防范页岩气钻井岩屑环境风险具有重要意义，为页岩气资源绿色、高效开采及安全利用提供有力支撑。

Guideline on available technologies of resource utilization for shale gas drilling cuttings in Chongqing

DB45/T 2650-2023 大理石废浆应用于湿法烟气脱硫技术规范

适用于广西壮族自治区行政区域内大理石废浆作为脱硫吸收剂的石灰石-石膏湿法烟气脱硫系统，其他大理石废浆的利用企业可参照执行。

Technical specification for application of marble waste slurry in wet flue gas desulfurization

T/SPSTS 027-2023 锂离子电池行业废隔膜回收技术规范

本文件规定了锂离子电池行业废隔膜回收的总体要求、类别与来源、隔膜鉴别方法、回收工艺以及环境保护和监测要求。 本文件适用于锂离子、钠离子或其他体系电池行业废隔膜的回收。

Technical Specifications for Recycling Waste Separators in Lithium-ion Battery Industry

T/CSUS 58-2023 污水处理厂污泥热解技术规范

本文件规定了污水处理厂污泥热解工艺流程，以及工程设计、施工、验收和运行等各阶段的技术要求。 本文件适用于污水处理厂生化污泥热解处理工程设计、施工和验收。

Technical specification for sludge pyrolysis in sewage treatment plants

T/CSUS 56-2023 城镇污水处理厂污泥热干化设备技术要求

本文件规定了适用于处理城镇污水处理厂污泥热干化设备（以下简称“干化设备”）所需达到的技术、经济、安全要求及标志、包装、运输和贮存。 本文件适用于城镇污水处理厂污泥热干化设备的设计、制造、工程应用与运行维护，用于处理其他废水污泥时可参照此文件执行。

Technical requirements for thermal drying equipment for sludge in urban sewage treatment plants

ASTM D6826-23 用作城市固体废物填埋场替代日常覆盖物的喷射泥浆、泡沫和本土材料的标准规范

1.1 This specification defines procedures for determining the performance of certain landfill daily cover materials generally described as an alternative daily cover (ADC). This specification applies only to slurries or foams that are spray applied, or indigenous materials that are placed onto the working face of a municipal solid waste landfill (MSWLF) unit as a cover. It is not applicable to other types of landfills nor geosynthetics used as an ADC. 1.2 This standard addresses the evaluation of an ADC and its ability to control fires and odors and whether or not the cover contains materials that present a threat to human health and the environment. The control of disease vectors and blowing litter can be evaluated by observation, and scavenging is controlled by security procedures and other operating practices. 1.3 The U.S. Environmental Protection Agency (EPA) promulgated regulations under the Resource Conservation and Recovery Act, Subtitle D, which establish criteria for municipal solid waste landfills (MSWLF). These regulations became effective October 9, 1991. The cover material requirements of these regulations are set forth in 40 Code of Federal Regulations, Section 258.21 as follows: (a) “Except as provided in paragraph (b) of this section, the owners or operators of all MSWLF units must cover disposed solid waste with 6 in. (152.4 mm) of earthen material at the end of each operating day, or at more frequent intervals if necessary, to control disease vectors, fires, odors, blowing litter, and scavenging.” (b) “Alternative materials of an alternative thickness (other than at least 6 in. (152.4 mm) of earthen material) may be approved by the Director of the Solid Waste Regulatory Agency of an approved State if the owner or operator demonstrates that the alternative material and thickness control disease vectors, fires, odors, blowing litter, and scavenging without presenting a threat to human health and the environment.” 1.3.1 These federal regulations have the force of the law, and it is the purpose of this specification to define the test procedures necessary to comply with these regulations. 1.3.2 In order for a MSWLF landfill operator to obtain approval for use of an ADC, the operator must supply performance data to the state Solid Waste Regulatory Agency. In general, the technique used to obtain this permission involves applying to the state Solid Waste Regulatory agency for a sanitary MSWLF operating permit modification. NOTE 1—Manufacturers will provide performance data for their product. 1.3.3 Parties interested in the evaluation technology described in the Standard Practice should include MSWLF operators, engineering firms, local, state, and federal Solid Waste Regulatory Agencies, and manufacturers and vendors of ADC materials. 1.4 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 This specification is under the jurisdiction of ASTM Committee D18 on Soil and Rock and is the direct responsibility of Subcommittee D18.25 on Erosion and Sediment Control Technology. Current edition approved April 1, 2023. Published April 2023. Originally approved in 2002. Last previous edition approved in 2014 as D6826 – 05 (2014)ɛ1 . DOI: 10.1520/D6826-23. *A Summary of Changes section appears at the end of this standard Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 2. Referenced Documents

Standard Specification for Sprayed Slurries, Foams and Indigenous Materials Used As Alternative Daily Cover for Municipal Solid Waste Landfills

T/HAEPCI 48-2023 钒冶炼废渣综合利用与处置技术规范

在继承和借鉴矿物冶炼废渣相关国家、地方及团体标准基础上，针对含钒矿物冶炼提钒的含钒废渣的特性，组成“钒冶炼废渣贮存、收集+钒冶炼废渣综合利用技术+钒冶炼废渣综合处置技术+管理制度”钒冶炼废渣综合利用与处置技术规范框架。 钒冶炼废渣综合利用与处置技术规范涉及：针对钒冶炼废渣特点以及化工冶炼废渣的综合利用与处置技术措施，主要分为：①钒冶炼废渣的收集与贮存，主要包括钒冶炼废渣的收集、钒冶炼废渣的运输包装、钒冶炼废渣的贮存；②钒冶炼废渣的综合利用技术，主要涉及有价组分回收（如回收钒、回收铁、回收镓等），综合利用（如用于水泥生产、用于混凝土及砂浆配制、用于钒钛黑瓷生产等）；③钒冶炼废渣的综合处置技术，主要包括无害化预处理（如脱铬、固化等），最终填埋处置措施（如选址、设计、渗滤液处理、终场覆盖与封场等）。

Technical specification for comprehensive utilization and disposal of vanadium smelting slag