13.220.40;29.020 标准查询与下载

DIN EN 60695-6-1:2011 着火危险试验.第6-1部分:烟雾模糊.一般指南(IEC 60695-6-1-2005 + A1-2010);德文版本EN 60695-6-1-2005 + A1-2010

Fire hazard testing - Part 6-1: Smoke obscuration - General guidance (IEC 60695-6-1:2005 + A1:2010); German version EN 60695-6-1:2005 + A1:2010

DS/EN 60695-2-12:2011 火灾危险测试 第 2-12 部分：基于发光/热线的测试方法 材料的灼热丝可燃性指数（GWFI）测试方法

This part of IEC 60695 specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for flammability testing to determine the glow-wire flammability index (GWFI). GWFI is the highest temperature, determined during this standardized procedure, at which the tested material; a) does not ignite or, if it does, extinguishes within 30 s after removal of the glow-wire and is not totally consumed;b) molten drips, if they occur, do not ignite the wrapping tissue. This test method is a materials test carried out on a series of standard test specimens. The data obtained, along with data f

Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials

IEC 60695-7-3:2011 着火危险试验.第7-3部分:火灾气流毒性试验结果的使用和解释

This part of IEC 60695 concerns laboratory tests used to measure the toxic components of the fire effluent from either electrotechnical products or materials used in electrotechnical products. It provides guidance on the use and interpretation of results from such tests. It discusses currently available approaches to toxic hazard assessment consistent with the approach of ISO TC 92 SC 3@ as set out in ISO 13344@ ISO 13571@ ISO 16312-1@ ISO 16312-2@ ISO 19701@ ISO 19702 and ISO 19706. It also provides guidance on the use of toxic potency data in fire hazard assessment and on principles which underlie the use of combustibility and toxicological information in fire hazard assessment. The methods described are applicable to data concerning both the incapacitating effects and the lethal effects of fire effluents. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is@ wherever applicable@ to make use of basic safety publications in the preparation of its publications. The requirements@ test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

Fire hazard testing - Part 7-3: Toxicity of fire effluent - Use and interpretation of test results

IEC 60695-7-2:2011 着火危险试验.第7-2部分:火灾气流毒性测试方法的概要和相关性原则

This part of IEC 60695 gives a brief summary of the test methods that are in common use in the assessment of acute toxic potency@ and other toxicity tests. It includes special observations on their relevance to real fire scenarios and gives recommendations on their use. It advises which tests provide toxic potency data that are relevant to real fire scenarios@ and which are suitable for use in fire hazard assessment and fire safety engineering. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is@ wherever applicable@ to make use of basic safety publications in the preparation of its publications. The requirements@ test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

Fire hazard testing - Part 7-2: Toxicity of fire effluent - Summary and relevance of test methods

BS EN 60695-1-11:2011 火险试验.电工产品火险隐患的评估指南.火险评估

This part of IEC 60695-1 provides guidance for assessing the fire hazard of electrotechnical products and for the resulting development of fire hazard testing as related directly to harm to people, animals or property. For the purposes of this standard, product means complete electrotechnical equipments, their parts (including components) and electrical insulating materials. It outlines a hazard-based process to identify appropriate fire test methods and performance criteria for products. The principles of the methodology are to identify fire events (fire scenarios) which will be associated with the product, to establish how the measurable fire properties of the product are related to the possible occurrence and outcome of those events, and to establish test methods and performance requirements for those properties which will either result in a tolerable fire outcome or eliminate the event altogether. This standard is intended as guidance to IEC committees, and should be used with respect to their individual applications. The actual implementation of this standard remains the responsibility of each product committee, according to the minimum acceptable fire safety in its application field and taking into account the feedback from experience. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

Fire hazard testing. Guidance for assessing the fire hazard of electrotechnical products. Fire hazard assessment

DIN EN 60695-7-1:2011 着火危险试验.第7-1部分:燃烧废气的毒性.通用指南(IEC 60695-7-1-2010);德文版本EN 60695-7-1-2010

Fire hazard testing - Part 7-1: Toxicity of fire effluent - General guidance (IEC 60695-7-1:2010); German version EN 60695-7-1:2010

IEC 89/1055/DTS:2011 IEC 60695-6-31 TS,版本2.0:火灾测试.第6-31部分:烟气灰暗度.小规模静态方法.材料

IEC 60695-6-31 TS, Ed. 2.0: Fire hazard testing - Part 6-31: Smoke obscuration - Small-scale static method - Materials

DS/EN 60695-1-11:2011 火灾危险测试 第 1-11 部分：电工产品火灾危险评估指南 火灾危险评估

This part of IEC 60695 provides guidance for assessing the fire hazard of electrotechnical products and for the resulting development of fire hazard testing as related directly to harm to people, animals or property. For the purpose of this standard, product means complete electrotechnical equipments, their parts (including components) and electrical insulating materials.This international standard outlines a hazard-based process to identify appropriate fire test methods and performance criteria for products. The principles of the methodology are to identify fire events (fire scenarios) which will be associated with the product, to establish how the measura

Fire hazard testing - Part 1-11: Guidance for assessing the fire hazard of electrotechnical products - Fire hazard assessment

GOST R IEC 60695-2-10-2011 火灾危险测试.第2-10部分:灼热丝测试方法.灼热丝装置和一般检测规程

Fire hazard testing. Part 2-10. Glowing/hot-wire based test methods. Glow-wire apparatus and common test procedures

GOST R IEC 60695-2-2-2011 火灾危险测试.第2部分:检测方法.第2节.针焰测试

Fire hazard testing. Part 2. Test methods. Section 2. Needle-flame test

DS/EN 60695-6-1/A1:2010 火灾隐患测试 第 6-1 部分：烟雾遮挡 一般指南

Gives guidance on: a) optical measurement of smoke obscuration; b) general aspects of optical smoke test methods; c) consideration of test methods; d) expression of smoke test data; e) relevance of optical smoke data to hazard assessment. The main changes with respect to the previous edition are listed below: - Modified title. - Updated normative references. - Expanded terms and definitions. - Numerous editorial changes of a technical nature throughout the publication. - A flowchart has been added for the evaluation and consideration of smoke test methods. Has the status of a basic safety publication in accordance with IEC Guide 104

Fire hazard testing - Part 6-1: Smoke obscuration - General guidance

DIN EN 60695-1-10:2010 着火危险试验.第1-10部分:电工产品着火危险评定指南.通用指南(IEC 60695-1-10-2009);德文版本EN 60695-1-10-2010

Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines (IEC 60695-1-10:2009); German version EN 60695-1-10:2010

DS/EN 60695-7-1:2010 火灾危险测试 第 7-1 部分：火灾排放物的毒性 一般指南

IEC 60695-7-1:2010 provides guidance on the factors which affect the toxic hazard from fires involving electrotechnical products, and provides information on the methodologies recommended by ISO TC 92 (SC 3) for estimating and reducing the toxic hazard from fires, as expressed in ISO 19706, ISO 13344 and ISO 13571.There is no single test to realistically assess toxic hazard in fires. Small-scale toxic potency tests are not capable on their own of assessing the toxic hazard in fires. Current toxicity tests attempt to measure the toxic potency of a laboratory generated fire effluent. Toxic potency should not be confused with toxic hazard.The basic safety publ

Fire hazard testing - Part 7-1: Toxicity of fire effluent - General guidance

IEC 60695-2-12:2010 着火危险试验.第2-12部分:灼热金属丝/热丝的试验方法.灼热金属丝可燃性(灼热金属丝可燃性)材料的试验方法

This part of IEC 60695 specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for flammability testing to determine the glow-wire flammability index (GWFI). GWFI is the highest temperature, determined during this standardized procedure, at which the tested material a) does not ignite or, if it does, extinguishes within 30 s after removal of the glow-wire and is not totally consumed, and b) molten drips, if they occur, do not ignite the wrapping tissue. This test method is a materials test carried out on a series of standard test specimens. The data obtained, along with data from the glow-wire ignition temperature (GWIT) test method for materials, IEC 60695-2-13, can then be used in a preselection process in accordance with IEC 60695-1-30 to judge the ability of materials to meet the requirements of IEC 60695-2-11. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

Fire hazard testing. Part 2-12: Glowing/hot-wire based test methods .Glow-wire flammability index (GWFI) test method for materials

BS EN 60695-7-1:2010 着火危险试验.燃烧废物的毒性.一般指南

This part of IEC 60695 provides guidance on the factors which affect the toxic hazard from fires involving electrotechnical products, and provides information on the methodologies recommended by ISO TC 92 (SC 3) for estimating and reducing the toxic hazard from fires, as expressed in ISO 19706, ISO 13344 and ISO 13571. There is no single test to realistically assess toxic hazard in fires. Small-scale toxic potency tests are not capable on their own of assessing the toxic hazard in fires. Current toxicity tests attempt to measure the toxic potency of a laboratory generated fire effluent. Toxic potency should not be confused with toxic hazard. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

Fire hazard testing. Part 7-1: Toxicity of fire effluent. General guidance

BS EN 60695-1-10:2010 火灾隐患试验.电工产品学的火灾隐患评估指南.一般原则

This part of IEC 60695-1 provides general guidance on how to reduce to acceptable levels the risk of fire and the potential effects of fires involving electrotechnical products. It also serves as a signpost standard to the other guidance publications in the IEC 60695 series. It describes the relationship between fire risk and the potential effects of fire, and provides guidance to IEC product committees on the applicability of qualitative and quantitative fire tests to the fire hazard assessment of electrotechnical products. It emphasises the importance of the scenario approach to fire hazard and risk assessment and discusses criteria intended to ensure the development of technically sound hazard-based fire test methods. It discusses the different types of fire tests, in particular, the nature of qualitative and quantitative fire tests. It also describes the circumstances under which it is appropriate for IEC product committees to maintain or develop qualitative fire tests. This standard is intended as guidance to IEC committees, and should be used with respect to their individual applications. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

Fire hazard testing - Guidance for assessing the fire hazard of electrotechnical products - General guidelines

NF C20-924-1-10:2010 火灾隐患试验.第1-10部分:电工产品火灾隐患评估导则.一般导则

Fire hazard testing - Part 1-10 : guidance for assessing the fire hazard of electrotechnical products - General guidelines.

IEC 60695-1-11:2010 火灾隐患试验.第1-10部分:电工产品的火灾隐患评估指南.火灾隐患评估

This part of IEC 60695-1 provides guidance for assessing the fire hazard of electrotechnical products and for the resulting development of fire hazard testing as related directly to harm to people, animals or property. For the purposes of this standard, product means complete electrotechnical equipments, their parts (including components) and electrical insulating materials. It outlines a hazard-based process to identify appropriate fire test methods and performance criteria for products. The principles of the methodology are to identify fire events (fire scenarios) which will be associated with the product, to establish how the measurable fire properties of the product are related to the possible occurrence and outcome of those events, and to establish test methods and performance requirements for those properties which will either result in a tolerable fire outcome or eliminate the event altogether. This standard is intended as guidance to IEC committees, and should be used with respect to their individual applications. The actual implementation of this standard remains the responsibility of each product committee, according to the minimum acceptable fire safety in its application field and taking into account the feedback from experience. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

Fire hazard testing - Part 1-11: Guidance for assessing the fire hazard of electrotechnical products - Fire hazard assessment

IEC 60695-7-1:2010 火灾隐患试验.第7-1部分:燃烧废物毒性.一般指南

This part of IEC 60695 provides guidance on the factors which affect the toxic hazard from fires involving electrotechnical products, and provides information on the methodologies recommended by ISO TC 92 (SC 3) for estimating and reducing the toxic hazard from fires, as expressed in ISO 19706, ISO 13344 and ISO 13571. There is no single test to realistically assess toxic hazard in fires. Small-scale toxic potency tests are not capable on their own of assessing the toxic hazard in fires. Current toxicity tests attempt to measure the toxic potency of a laboratory generated fire effluent. Toxic potency should not be confused with toxic hazard. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

Fire hazard testing - Part 7-1: Toxicity of fire effluent - General guidance

DS/EN 60695-1-10:2010 火灾危险测试 第 1-10 部分：电工产品火灾危险评估指南 一般指南

This part of IEC 60695-1 provides general guidance on how to reduce to acceptable levels therisk of fire and the potential effects of fires involving electrotechnical products. It also servesas a signpost standard to the other guidance publications in the IEC 60695 series.It describes the relationship between fire risk and the potential effects of fire, and providesguidance to IEC product committees on the applicability of qualitative and quantitative firetests to the fire hazard assessment of electrotechnical products.It emphasises the importance of the scenario approach to fire hazard and risk assessmentand discusses criteria intended to ensure the develo

Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines