共找到 243 条与 特殊螺纹 相关的标准,共 17 页
Locking threads with 30 degree wedge ramp
GB/T 15054的本部分规定了小螺纹的牙型、直径与螺距系列和基本尺寸。 本部分适用于公称直径范围为0.3 mm~1.4 mm的一般用途小螺纹。
Miniature screw threads.Part 1:Profiles, general plan and basic dimensions
GB/T 15054的本部分规定了小螺纹的公差、极限尺寸、标记和检验。 本部分适用于公称直径范围为0.3 mm~1.4 mm的一般用途小螺纹。
Miniature screw threads.Part 2:Tolerances and limits of size
本标准规定了牙型角为80°、螺纹副不具有密封性的圆柱管螺纹的牙型、尺寸、公差、标记和检验。本标准适用于薄壁管件的螺纹连接。
Pipe threads with 80 degree thread angle where pressure-tight joints are not made on the threads
GB/T 13576的本部分规定了锯齿形螺纹的直径与螺距组合系列。其牙型符合GB/T 13576.1的规定。 本部分适用于一般用途的机械传动和紧固锯齿形螺纹连接。
Buttress threads with the flank angles of 3 and 30 degrees.Part 2:General plan
GB/T 13576的本部分规定了锯齿形螺纹的基本尺寸。锯齿形螺纹的牙型和直径与螺距系列分别符合GB/T 13576.1和GB/T 13576.2的规定。 本部分适用于一般用途的机械传动和紧固锯齿形螺纹连接。
Buttress threads with the flank angles of 3 and 30 degrees.Part 3:Basic dimensions
GB/T 13576的本部分规定了锯齿形螺纹的基本牙型和设计牙型。 本部分适用于一般用途机械传动和紧固的锯齿形螺纹连接。
Buttress threads with the flank angles of 3 and 30 degrees.Part 1:Profiles
本标准规定了牙型角为60°、米制密封螺纹的牙型、基本尺寸、公差和标记。 内螺纹有圆锥内螺纹和圆柱内螺纹两种,外螺纹仅有圆锥外螺纹一种。内、外螺纹可以组成两种密封配合形式:圆锥内螺纹与圆锥外螺纹组成“锥/锥”配合;圆柱内螺纹与圆锥外螺纹组成“柱/锥”配合。 本标准适用于管子、阀门、管接头、旋塞等产品上的一般密封螺纹联结。装配时,推荐在螺纹副内添加合适的密封介质,例如密封胶带、密封胶等。
Metric threads where pressure-tight joints are made on the threads
GB/T 13576的本部分规定了锯齿形螺纹的公差和标记。锯齿形螺纹的牙型和直径与螺距系列分别符合GB/T 13576.1和GB/T 13576.2的规定。 本部分适用于一般用途机械传动和的锯齿形螺纹连接。
Buttress threads with the flank angles of 3 and 30 degrees.Part 4:Tolerances
本标准规定了牙型角为60°、螺纹副本身具有密封性管螺纹(NPT和NPSC)的牙型、基本尺寸、公差和标记。 内螺纹有圆锥内螺纹和圆柱内螺纹两种,外螺纹仅有圆锥外螺纹一种。内、外螺纹可组成两种密封配合形式:圆锥内螺纹与圆锥外螺纹组成“锥/锥”配合,圆柱内螺纹与圆锥外螺纹组成“柱/锥”配合。 本标准适用于管子、阀门、管接头、旋塞及其他管路附件的密封螺纹联接。 为确保螺纹联接密封的可靠性,应在螺纹副内添加合适的密封介质,例如在螺纹表面上缠胶带、涂密封胶等。
Pipe threads with the thread angle of 60 degrees where pressure-tight joints are made on the threads
本标准规定了牙型角为55°、螺纹副本身具有密封性的圆锥内螺纹 和圆锥外螺纹的牙型、尺寸、公差和标记。 本标准适用于管子、阀门、管接头、旋塞及其他管路附件的螺纹联结。 允许在螺纹副内添加合适的密封介质,例如在螺纹表面缠胶带、涂密封胶等。
Pipe threads with 55 degree thread angle where pressure-tight joints are made on the threads Part 2:Taper internal and external threads
本标准规定了牙型角为55°、螺纹副本身具有密封性的圆柱内螺纹和圆锥外螺纹的牙型、尺寸、公差和标记。 本标准适用于管子、阀门、管接头、旋塞及其他管路附件的螺纹联结。 允许在螺纹副内添加合适的密封介质,例如在螺纹表面缠胶带、涂密封胶等。
Pipe threads with 55 degree thread angle where pressure-tight joints are made on the threads Part 1:Parallel internal and taper external threads
本标准规定了《梯形螺纹》中内、外螺纹选用公差带的极限尺寸。 本标准适用于GB5796.1一57196.4-86所规定的梯形螺纹。
Limits of sizes for metric trapezoidal screw threads
Test methods for screw for timber structure
Gas cylinders. Parallel threads for connection of valves to gas cylinders. Specification
This standard gives for threads up to 8 mm lead excerpts from DIN ISO 965-1 and for threads with leads above 8 mm additional information, e. g. for es.
Metric buttress threads - Part 3: Deviations and tolerances
This standard describes metric buttress threads with profiles according to DIN 513-1.
Metric buttress threads - Part 2: General plan
This standard gives the basic profile of metrical buttress threads, i.e. the theoretical profile, to which the tolerances of the outer, inner and pitch diameter belong.
Metric buttress threads - Part 1: Thread profiles
ISO miniature screw threads — Amendment 1: The figure for the tolerance zone of external thread
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号