共找到 998 条与 管道部件和管道综合 相关的标准,共 67 页
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U). Guidance for the assessment of conformity
Plastics piping systems for hot and cold water installations – Chlorinated poly(vinyl chloride) (PVC-C) – Part 2: Pipes – Amendment 2 (ISO 15877-2:2009/Amd 2:2020)
2021 UNIFORM PLUMBING CODE (twenty-ninth edition ; First Printing, February 2020)
Gas distribution systems. Design, construction and liquidation of natural gas distribution networks. Part 0. General requirements
Gas distribution systems. Design, construction and liquidation of natural gas distribution networks. Part 1. Polyethylene gas pipelines
1.1?This test method defines procedures for testing vitrified clay pipe lines, using low-pressure air, to demonstrate the integrity of the installed line. Refer to Practice C12. 1.2?This test method shall be performed on lines after connection laterals, if any, have been plugge
Standard Test Method for Low-Pressure Air Test of Vitrified Clay Pipe Lines
1.范围 本文件规定了螺旋缠绕管道修复技术要求的基本要求、设计、施工准备、技术要求、试验与验收。 本文件适用于城镇公共排水管道进行的非开挖修复与更换。 2.术语和定义 本文件规定了“螺旋缠绕法”、“管道修复技术”的定义。 3.基本要求 本文件规定了螺旋缠绕管道修复技术的基本要求。 4.设计 本文件规定了螺旋缠绕管道修复技术的设计要求。 5.施工准备 本文件规定了螺旋缠绕管道修复技术的施工准备。 6. 技术要求 本文件规定了螺旋缠绕管道修复技术的技术要求。 7.试验与验收 本文件规定了螺旋缠绕管道修复技术的试验与验收。
Technical requirements for repair of spiral wound pipe
Plastics piping systems for hot and cold water installations – Crosslinked polyethylene (PE-X) – Part 5: Fitness for purpose of the system – Amendment 1 (ISO 15875-5:2003/Amd 1:2020)
Plastics piping systems for hot and cold water installations – Polyethylene of raised temperature resistance (PE-RT) – Part 5: Fitness for purpose of the system – Amendment 1 (ISO 22391-5:2009/Amd 1:2020)
Metallic industrial piping -- Part 3: Design and calculation
Plastics piping systems for hot and cold water installations – Chlorinated poly(vinyl chloride) (PVC-C) – Part 5: Fitness for purpose of the system – Amendment 2 (ISO 15877-5:2009/Amd 2:2020)
Plastics piping systems for hot and cold water installations – Crosslinked polyethylene (PE-X) – Part 2: Pipes – Amendment 2 (ISO 15875-2:2003/Amd 2:2020)
状况不明工业管道安全评估基本程序一般包含:项目调查、制定方案、安全评估项目、评估报告、评估结论。
Safety assessment rules for industrial pipelines with unknown conditions
Ductile iron pipelines — Hydrostatic testing after installation
Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 5: Fitness for purpose of the system - Amendment 1 (ISO 22391-5:2009/Amd 1:2020, Corrected version 2021-03)
Standard test method for water penetration into pipeline coatings
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U). Specifications for pipes, fittings and the system
Plastics piping systems for non-pressure underground drainage and sewerage--Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)--Part 2: Specifications for pipes and fittings with smooth i
1.1 The purpose of EN 13480 is to define the requirements for design, manufacture, installation, testing and inspection of industrial piping systems and supports, including safety systems, made of metallic materials (but initially restricted to steel) with a view to ensure safe o
Metallic industrial piping - Part 3: Design and calculation; German version EN 13480-3:2017/A3:2020
Specifies the design and calculation of industrial metallic piping systems, including supports, covered by EN 13480. Revision of Clause 12 and Annex H related to Stress Intensification Factors SIF
Metallic industrial piping - Part 3: Design and calculation; German version EN 13480-3:2017/A2:2020
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号