23.040.20 塑料管 标准查询与下载

BS ISO 9854-2:2023 用于输送流体的热塑性塑料管道 夏比冲击性能的测定 各种材料管材的试验条件

Thermoplastics pipes for the transport of fluids. Determination of Charpy impact properties - Test conditions for pipes of various materials

ASTM F891-23 带蜂窝芯的共挤聚氯乙烯塑料管标准规范

Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core

ASTM D6041-23 接触模压“玻璃纤维”（玻璃纤维增强热固性树脂）耐腐蚀管道和配件的标准规范

1.1 This specification covers pipe and fittings fabricated by contact molding, for pressures to 150 psi and made of a commercial-grade polyester resin. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship, and appearance. 1.2 This specification does not cover resins other than polyester, reinforcing materials other than glass fibers or fabrication methods other than contact molding. NOTE 1—For the purposes of this specification, the term polyester resin will include both polyester and vinylester resins. 1.3 This specification does not cover the design of pipe and fittings intended for use with liquids heated above their flash points. 1.4 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are provided for information purposes only. 1.5 The following precautionary caveat pertains only to Section 10, the test methods portion, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 2—There is no known ISO equivalent to this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings

BS ISO 8513:2023 塑料管道系统 玻璃增强热固性塑料 (GRP) 管道 测定初始纵向拉伸强度的试验方法

Plastics piping systems. Glass-reinforced thermosetting plastics (GRP) pipes. Test methods for the determination of the initial longitudinal tensile strength

ASTM F412-23 与塑料管道系统相关的标准术语

1.1  This terminology is a compilation of definitions of technical terms used in the plastic piping industry. Terms that are generally understood or adequately defined in other readily available sources are not included. 1.2  When a term is used in an ASTM document for which Committee F17 is responsible it is included only when judged, after review, by Subcommittee F17.91 to be a generally usable term. 1.3  Definitions that are identical to those published by other ASTM committees or other standards organizations are identified with the committee number (for example, D20) or with the abbreviation of the name of the organization (for example, IUPAC International Union of Pure and Applied Chemistry). 1.4  A definition is a single sentence with additional information included in notes. 1.5  Definitions are followed by the committee responsible for the standard(s) (for example, [F17.26]) and standard numbers(s) in which they are used (for example, F714 ). 1.6  Abbreviated Terminology:  1.6.1  Abbreviated terminology is intended to provide uniform contractions of terms relating to plastic piping that have evolved through widespread common usage. The compilation in this standard has been prepared to avoid the occurrence of more than one abbreviated term for a given plastics piping term and to avoid multiple meanings for abbreviated terms. 1.6.2  The abbreviated terminology and descriptions in this standard are intended to be consistent with usage in plastics piping and the standards under F17 jurisdiction. Other ASTM Committees may assign a different word-phrase description to the same abbreviated terminology. In such cases, the abbreviated terms in this standard shall apply to usage in F17 standards, or if widespread misunderstanding could result from conflicting abbreviated terminology descriptions, the abbreviated terminology for the word-phrase shall not be used in F17 standards. 1.6.3  Acronyms and Initialisms— A word formed from the letters or parts of words of a longer word-phrase, usually from the initial letters or parts of the words. An Acronym is pronounced as a word, for example radar, for radio detection and ranging. An Initialism is pronounced as a series of letters, for example DOT for Department of Transportation. 1.6.4  The Acronym or Initialism description is the origin word-phrase for the Acronym or Initialism, not a definition. 1.7  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Terminology Relating to Plastic Piping Systems

ASTM F758-14(2023) 公路、机场和类似排水系统的光滑壁聚氯乙烯 (PVC) 塑料暗渠系统的标准规范

1.1  This specification covers the requirements for smooth-wall perforated and nonperforated poly(vinyl chloride) (PVC) plastic pipe and couplings for use in subsurface drainage systems of highways, airports, and similar applications in nominal sizes of 4, 6, and 8 in. and in pipe stiffnesses (PS) that are designated as Type PS 28 and Type PS 46 in accordance with its minimum pipe stiffness. 1.2  Molded fittings for use with highway underdrain pipe are in accordance with Specification D3034 . For convenience, some of these fittings are reproduced in Annex A1 . 1.3  The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. Note 1:  Type PS 28 and Type PS 46 indicate “pipe stiffness” of 28 and 46, respectively, as outlined in 11.1 . Note 2:  Pipe and fittings should be installed in accordance with Practice D2321 , or applicable state or local specifications. 1.4  Units— The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5  The following safety hazards caveat pertains only to the test methods portion, Section 11 , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain Systems for Highway, Airport, and Similar Drainage

ASTM F628-23 带有蜂窝芯的丙烯腈-丁二烯-苯乙烯 (ABS) Schedule 40 塑料排水管、废物管和通风管的标准规范

1.1  This specification covers coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipe made to Schedule 40 iron pipe sizes (IPS) and produced by the coextrusion process with concentric inner and outer solid ABS layers and the core consisting of closed-cell cellular ABS. Plastic which does not meet the material requirements specified in Section 5 is excluded from single layer and all coextruded layers. 1.2  Fittings suitable for use with pipe meeting the requirements of this specification are given in Annex A1 . Fittings meeting the requirement of Specification D2661 are also acceptable. 1.3  Acrylonitrile-butadiene-styrene plastic which does not meet the definitions of virgin ABS plastic as given in 3.2.4 is excluded, as performance of plastic other than those defined as virgin was not determined. ABS rework plastic which meets the requirements of rework plastic as given in 5.3 is acceptable. 1.4  Reprocessed plastic or recycled plastic as defined in Terminology D883 is excluded. 1.5  Recommendations for storage, joining, and installation are provided in Appendix X1 , Appendix X2 , and Appendix X3 , respectively. 1.6  The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.7  The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.8  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core

ASTM F1281-23a 交联聚乙烯/铝/交联聚乙烯（PEX-AL-PEX）压力管道标准规范

1.1  This specification covers a coextruded crosslinked polyethylene composite pressure pipe with a welded aluminum tube reinforcement between the inner and outer layers. The inner and outer crosslinked polyethylene layers are bonded to the aluminum tube by a melt adhesive. Included is a system of nomenclature for the crosslinked polyethylene-aluminum-crosslinked polyethylene (PEX-AL-PEX) pipes, the requirements and test methods for materials, the dimensions of the component layers and finished pipe, adhesion tests, and the burst and sustained pressure performance. Also given are the requirements and methods of marking. The pipe covered by this specification is intended for use in potable water distribution systems for residential and commercial applications, water service, building supply lines, underground irrigation systems, and radient panel heating systems, baseboard, snow- and ice-melt systems, and gases that are compatible with the composite pipe and fittings. 1.2  This specification covers only composite pipes incorporating a welded aluminum tube. Pipes consisting of metallic layers not welded together are outside the scope of this specification. 1.3  Specifications for connectors for use with pipe meeting the requirements of this specification are given in Annex A1 . 1.4  This specification excludes polyethylene-aluminum-polyethylene pipes (see Specification F1282 ). 1.5  The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.6  The following precautionary caveat pertains only to the test methods portion, Section 9 , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe

ASTM F1473-23 用于测量聚乙烯管和树脂的缓慢裂纹扩展抗性的缺口拉伸试验的标准试验方法

1.1  This test method determines the resistance of polyethylene materials to slow crack growth under conditions specified within. Note 1:  This test method is known as PENT (Pennsylvania Notch Test) test. 1.2  The standard test is performed at 80 °C and at 2.4 MPa, but it shall be acceptable to conduct tests at a temperature below 80 °C and with other stresses low enough to preclude ductile failure and thereby eventually induce brittle type of failure. The standard test is conducted in an air environment; however, it shall be acceptable to immerse test specimens in an alternate environment such as water or a water/detergent solution, or other liquid or a different environment such as an inert gas to evaluate slow crack growth performance in different environments. Generally, polyethylenes will ultimately fail in a brittle manner by slow crack growth at 80 °C if the stress is at or below 2.4 MPa Note 2:  When testing in environments other than air, it is recommended to consider maintaining the efficacy of the test media (for example, a detergent solution) to minimize any effect of aging. 1.3  The test method is for specimens cut from compression molded plaques.2 See Appendix X1 for information relating to specimens from pipe. 1.4  The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins

ASTM D1598-23 恒定内压下塑料管失效时间的标准试验方法

1.1 This test method covers the determination of the timeto-failure of both thermoplastic and reinforced thermosetting/ resin pipe under constant internal pressure. 1.2 This test method provides a method of characterizing plastics in the form of pipe under the conditions prescribed. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure

ASTM D5365-23 “玻璃纤维”（玻璃纤维增强热固性树脂）管的长期环弯曲应变的标准测试方法

1.1 This test method covers a procedure for determining the long-term ring-bending strain (Sb) of “fiberglass” pipe. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP) are “fiberglass” pipes. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific warning statement is given in 9.5. NOTE 1—There is no known ISO equivalent to this standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Long-Term Ring-Bending Strain of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe

ASTM F2818-10(2023) 交联聚乙烯（PEX）材料气体压力管道规范

Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing

ASTM F2896-23 石油、天然气和危险液体运输用增强聚乙烯复合管标准规范

Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids

ASTM D3681-23 偏转条件下“玻璃纤维”（玻璃纤维增强热固性树脂）管道耐化学性的标准试验方法

1.1 This test method covers the procedure for determining the chemical-resistant properties of fiberglass pipe in a deflected condition for diameters 4 in. (102 mm) and larger. Both glass–fiber–reinforced thermosetting resin pipe (RTRP) and glass–fiber–reinforced polymer mortar pipe (RPMP) are fiberglass pipes. NOTE 1—For the purposes for this standard, polymer does not include natural polymers. 1.2 Inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 9.5. NOTE 2—There is no known ISO equivalent to this standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition

ASTM F2986-12(2023) 矿井渗滤液用波纹聚乙烯管和配件标准规范

Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate Applications

ASTM F3203-19(2023) 交联聚乙烯（PEX）管材凝胶含量测定的标准试验方法

Standard Test Method for Determination of Gel Content of Crosslinked Polyethylene (PEX) Pipes and Tubing

ASTM F2817-13(2023) 维护或修理用聚氯乙烯气体压力管和配件的标准规范

Standard Specification for Poly (Vinyl Chloride) (PVC) Gas Pressure Pipe and Fittings For Maintenance or Repair

ISO/PRF 10468:2023 玻璃增强热固性塑料（GRP）管 湿或干条件下环蠕变性能的测定

Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the ring creep properties under wet or dry conditions

ISO/CD 15875-5:2023 冷热水装置用塑料管道系统 交联聚乙烯 (PE-X) 第 5 部分：系统用途的适用性

Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 5: Fitness for purpose of the system

ISO 8513:2023 塑料管道系统 玻璃增强热固性塑料（GRP）管 测定初始纵向拉伸强度的试验方法

Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength