燃气轮机和蒸汽轮机、蒸汽机标准-分析测试百科网

ASTM D8323-20 蒸汽轮机电液控制（EHC）系统用在用磷酸酯基液体管理的标准指南

1.1 This guide provides recommendations to achieve safe and reliable operation of EHC systems, recommended levels for required corrective action, and suggested management practices. 1.2 The recommended set of physical and chemical properties of triaryl phosphate esters and their limits have been selected based on past operating experience with various fluids (primarily xylylated and butylated triaryl phosphate esters) used in different EHC system designs under different operating and environmental conditions. 1.3 This guide is not intended to replace Original Equipment Manufacturer (OEM) specifications but rather support users experiencing operating problems by recommending limits based on existing knowledge of triaryl phosphate ester degradation mechanisms. This guide should be used outside the warranty period or in cases where no OEM standard exists or is available. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Management of In-Service Phosphate Ester-based Fluids for Steam Turbine Electro-Hydraulic Control (EHC) Systems

ICS: 27.040
CCS
发布: 2020-06-01
实施

IEC 60045-1:2020 蒸汽轮机 - 第1部分:规格

Steam turbines - Part 1: Specifications

ICS: 27.040
CCS
发布: 2020-05-13
实施

ASTM D4378-20 用于蒸汽气体和联合循环涡轮机的矿物涡轮机油的在役监测的标准实践

Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines

ICS: 27.040
CCS
发布: 2020-05-01
实施

BS ISO 21905:2020 带或不带余热回收的燃气轮机排气系统

What is ISO 21905 about? ISO 21905 discusses gas turbine exhaust systems with or without heat recovery. ISO 21905 specifies requirements and gives recommendations for the design, materials of construction, modelling, controlling, fabrication, inspection, testing, installation, start-up and operation of industrial gas turbine (GT) exhaust systems with or without waste heat recovery unit (WHRU). Gas turbines can be on-shore or off-shore for such sectors as oil and gas, chemical and process industries, utilities, or other intensive energy users. For ISO 21905 , the exhaust system means all items in the turbine exhaust gas stream between the GT exhaust gas collector outlet flange and the termination/s to the atmosphere. The following items are not covered by ISO 21905 : heat recovery steam generator equipment (HRSG) supplementary fired systems

Gas turbine exhaust systems with or without waste heat recovery

ICS: 27.040
CCS
发布: 2020-03-31
实施: 2020-03-31

ISO 21905:2020 有或无余热回收的燃气轮机排气系统

This document specifies requirements and gives recommendations for the design, materials of construction, modelling, controlling, fabrication, inspection, testing, installation, start-up and operation of industrial gas turbine (GT) exhaust systems with or without waste heat recovery unit (WHRU). Gas turbines can be on-shore or off-shore for such sectors as oil and gas, chemical and process industries, utilities, or other intensive energy users. For this document, the exhaust system means all items in the turbine exhaust gas stream between the GT exhaust gas collector outlet flange and the termination/s to the atmosphere. The following items are not covered by this document: — heat recovery steam generator equipment (HRSG); — supplementary fired systems; — auxiliary fired systems; — exhaust gas collector (also known as exhaust plenum); — fire detection and extinguishing systems; — emissions controls equipment intended to modify the gaseous composition of the exhaust gas; — WHRUs that are of the firetube type, where the turbine exhaust gas (TEG) passes through the tubes.

Gas turbine exhaust systems with or without waste heat recovery

ICS: 27.040
CCS
发布: 2020-03-05
实施

T/CSEE 0101.2-2020 发电设备相控阵超声检测技术导则第2部分

T/CSEE 0101的本部分规定了汽轮机转子相控阵超声检测一般要求、检测方法和缺陷评定方法。本部分适用于整锻式汽轮机转子，焊接汽轮机转子、含中心孔汽轮机转子、发电机转子的相控阵超声检测参照本部分执行。

Technical Guidelines for Phased Array Ultrasonic Testing of Power Generation Equipment Part 2

ICS: 27.040
CCS: D4420
发布: 2020-01-01
实施: 2022-07-13

T/CSEE 0101.1-2020 发电设备相控阵超声检测技术导则第1部分：

下列文件对于本文件的应用是必不可少的。凡是注日期的引用文件，仅注日期的版本适用于本文件。凡是不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。 GB/T 12604.1-2005 无损检测术语超声检测 GB/T 20737-2006 无损检测通用术语和定义 GB/T 32563 无损检测超声检测相控阵超声检测方法 JB/T 8428-2015 无损检测超声试块通用规范 JJF 1338-2012 相控阵超声探伤仪校准规范

Technical Guidelines for Phased Array Ultrasonic Testing of Power Generation Equipment Part 1: