29.040.10 绝缘油 标准查询与下载

IEC TR 62697-3:2018 从未使用和已使用绝缘油中腐蚀性硫化物定量测定试验方法.第3部分:元素硫定量测定的试验方法

This part of IEC 62697 specifies a test method for the quantitative determination of elemental sulfur in used and unused insulating liquids over a 2 mg kg-1 to 400 mg kg-1 concentration range.

Test methods for quantitative determination of corrosive sulfur compounds in unused and used insulating liquids - Part 3: Test method for quantitative determination of elemental sulfur

IEC TR 62697-2:2018 从未使用和已使用绝缘油中腐蚀性硫化物定量测定试验方法.第2部分:总腐蚀硫（TCS）定量测定的试验方法

This part of IEC 62697 specifies a test method for the quantitative determination of total corrosive sulfur (TCS) in unused and used insulating liquids and solid matrices through the conversion of corrosive sulfur species to metal (copper, silver etc.) sulfides. The sulfides formed are quantitatively converted to sulfates; sulfates are determined through turbidity measurement or with ion chromatography. The method is applicable with the following matrices: a) Unused and used insulating liquids, for example mineral insulating oils and natural esters, which allow the determination of corrosive sulfur compounds over concentrations ranging between 2,5 mg kg-1 to 80 mg kg-1 TCS. b) Solid matrices that come in contact with the insulating liquid, for example insulating papers in electrical equipment. The quantification limits for these matrices depend on the amount of matrix used during the determination. The method can be used for the quantitative or semi-quantitative determination of copper sulfide on paper after the test according to IEC 62535. The method can provide unambiguous quantitative assessment of copper sulfide present on paper rather than qualitative results obtained with the SEM-EDX examination stipulated in case of doubts in the interpretation of results obtained from the inspection of paper according to IEC 62535:2008, 6.3. c) Paper and other solid insulating material/s obtained from failed transformers, reactors and other electrical equipment to assist in failure diagnostics. d) Metal deactivator or passivators additives present in insulating liquids (qualitative assessment). However, the method is not applicable for assessing corrosion phenomena for example the dissolution of copper in insulating liquids and deposition on solid matrices, which do not lead to sulfide formation.

Test methods for quantitative determination of corrosive sulfur compounds in unused and used insulating liquids - Part 2: Test method for quantitative determination of total corrosive sulfur (TCS)

IEC 61125:2018 绝缘液体氧化稳定性试验方法评估绝缘液体交货状态下氧化稳定性的试验方法

Insulating liquids - Test methods for oxidation stability - Test method for evaluating the oxidation stability of insulating liquids in the delivered state

ASTM D3612-02(2017) 气相色谱法分析电绝缘油中溶解气体的标准试验方法

1.1 This test method covers three procedures for extraction and measurement of gases dissolved in electrical insulating oil having a viscosity of 20 cSt (100 SUS) or less at 40°C (104°F), and the identification and determination of the individual component gases extracted. Other methods have been used to perform this analysis. 1.2 The individual component gases that may be identified and determined include: Hydrogen—H2 Oxygen—O2 Nitrogen—N2 Carbon monoxide—CO Carbon dioxide—CO2 Methane—CH4 Ethane—C2H6 Ethylene—C2H4 Acetylene—C2H2 Propane—C3H8 Propylene—C3H6 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements see 6.1.8, 30.2.2 and 30.3.1. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Analysis of Gases Dissolved in Electrical Insulating Oil by Gas Chromatography

ASTM D6871-17 电器用天然（植物油）酯流体的标准规范

1.1 This specification covers a high fire point natural vegetable oil ester insulating fluid for use as a dielectric and cooling medium in new and existing power and distribution electrical apparatus such as transformers and attendant equipment. 1.2 Natural vegetable oil ester insulating fluid differs from conventional mineral oil and other high fire point (or “lessflammable”) fluids in that it is an agricultural product derived from vegetable oils rather than refined from petroleum base stocks or synthesized from organic precursors. 1.3 This specification is intended to define a natural vegetable oil ester electrical insulating fluid that is compatible with typical materials of construction of existing apparatus and will satisfactorily maintain its functional characteristic in this application. The material described in this specification may not be miscible with some synthetic electrical insulating liquids. The user should contact the manufacturer of the natural ester insulating fluid for guidance in this respect. 1.4 This specification applies only to new insulating fluid as received prior to any processing. The user should contact the manufacturer of the equipment or fluid if questions of recommended characteristics or maintenance procedures arise. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Natural (Vegetable Oil) Ester Fluids Used in Electrical Apparatus

ASTM D1534-95(2017) 通过颜色指示剂滴定测定电绝缘液体中大致酸度的标准测试方法

1.1 This test method describes the determination of the approximate total acid value of used electrical insulating liquids having viscosities less than 24 cSt at 40°C. It is a simple procedure that can be applied in the field. Where a quantitative neutralization value is required, use Test Method D664 or Test Method D974. These test methods should be applied in the laboratory. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Approximate Acidity in Electrical Insulating Liquids by Color-Indicator Titration

KS C 2101-2017(英文版) 电绝缘油的试验方法

Testing methods of electrical insulating oils

KS C 2101-2017 电绝缘油的测试方法

Testing methods of electrical insulating oils

ASTM D6710-17 评估烃基淬火油的标准指南

4.1 The significance and use of each test method will depend on the system in use and the purpose of the test method listed under Section 6. Use the most recent editions of the test methods. 1.1 This guide covers information without specific limits, for selecting standard test methods for testing hydrocarbon-based quench oils for quality and aging. 1.2 The values stated in SI units are to be regarded as standard. 1.2.1 Exception—The units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Evaluation of Hydrocarbon-Based Quench Oil

T/CEEIA 253-2016 风力发电机绝缘处理用无溶剂浸渍树脂技术要求

本标准规定了风力发电机绝缘处理用无溶剂浸渍树脂的性能要求，试验方法，检验规则，标志、包装、储存与运输。

Technical Requirements for Solvent-Free Impregnating Resin of Insulating Treatment of Wind Turbine Generator

GSO ASTM D6710:2016 烃基淬火油评价标准指南

1.1 This guide covers information without specific limits, for selecting standard test methods for testing hydrocarbon-based quench oils for quality and aging. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to its use.

Standard Guide for Evaluation of Hydrocarbon-Based Quench Oil

ASTM D5222-16 高火点矿物绝缘油标准规范

1.1 This specification describes a high fire-point mineral oil based insulating fluid, for use as a dielectric and cooling medium in new and existing power and distribution electrical apparatus, such as transformers and switchgear. 1.2 High fire-point insulating oil differs from conventional mineral insulating oil by possessing a fire-point of at least 300°C. High fire-point mineral insulating oils are also referred to as “less flammable” mineral insulating oils.This property is necessary in order to comply with certain application requirements of the National Electrical Code (Article 450-23) or other agencies. The material discussed in this specification is miscible with other petroleum based insulating oils. Mixing high fire-point liquids with lower fire point hydrocarbon insulating oils (for example, Specification D3487 mineral oil) may result in fire points of less than 300°C. 1.3 This specification is intended to define a high fire-point electrical mineral insulating oil that is compatible with typical material of construction of existing apparatus and will satisfactorily maintain its functional characteristic in its application in this application. The material described in this specification may not be miscible with electrical insulating liquids of non-petroleum origin. The user should contact the manufacturer of the high fire-point insulating oil for guidance in this respect. 1.4 This specification applies only to new insulating material oil as received prior to any processing. Information on in-service maintenance testing is available in appropriate guides.2 The user should contact the manufacturers of the equipment or oil if questions of recommended characteristics or maintenance procedures arise. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Specification for High Fire-Point Mineral Electrical Insulating Oils

ASTM D3487-16 电气装置使用矿物绝缘油的标准规格

1.1 This specification covers unused mineral insulating oil of petroleum origin for use as an insulating and cooling medium in new and existing power and distribution electrical apparatus, such as transformers, regulators, reactors, circuit breakers, switchgear, and attendant equipment. 1.2 This specification is intended to define a mineral insulating oil that is functionally interchangeable and miscible with existing oils, is compatible with existing apparatus and with appropriate field maintenance,2 and will satisfactorily maintain its functional characteristics in its application in electrical equipment. This specification applies only to new insulating oil as received prior to any processing. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus

GSO IEC 60666:2016 矿物绝缘油中特定添加剂的检测和测定

IEC 60666:2010 provides methods concerning the detection and determination of specified additives in unused and used mineral insulating oils. The detection methods may be applied to assess whether or not a mineral insulating oil contains an additive as specified by the supplier. The determination methods are used for the quantitative determination of additives known to be present or previously detected by the appropriate detection method. The main changes with respect to the previous edition are listed below: - a change in the title from "Detection and determination of specified anti-oxidant additives in insulating oils"; - new Annexes B and C which provide methods for the determination of two additives different from the anti-oxidants.

Detection and determination of specified additives in mineral insulating oils

GSO IEC 61125:2016 基于绝缘液体的未使用的碳氢化合物 评估氧化稳定性的测试方法

Describes three test methods using the same apparatus for evaluating the oxidation stability of mineral insulating oils and of hydrocarbon-based insulating liquids. A method for evaluating the oxidation stability of unused uninhibited mineral insulating oils under accelerated conditions, a method for oils, a method for unused uninhibited and inhibited hydrocarbon insulating liquids. Replaces IEC 60074 (1963), IEC 60474 (1974) and IEC 60813 (1985). The contents of the corrigendum of September 1992 have been included in this copy.

Unused hydrocarbon based on insulating liquids – Test methods for evaluating the oxidation stability.

DIN EN 60836:2016 电工用未用硅绝缘液体的规范(IEC 60836-2015).德文版本EN 60836-2015

Specifications for unused silicone insulating liquids for electrotechnical purposes (IEC 60836:2015); German version EN 60836:2015

DL/T 1432.2-2016 变电设备在线监测装置检验规范 第2部分：变压器油中溶解气体在线监测装置

本部分规定了变压器油中溶解气体在线监测装置的检验条件、检验项目、仪器设备和材料、检验内容及要求、检验结果处理和检验周期等。 本部分适用于变压器油中溶解气体在线监测装置专项检验项目的检验。

Testing specification for on-line monitoring device of transformation equipment.Part 2: on-line monitoring device of gases dissolved in transformer oil

DL/T 1550-2016 矿物绝缘油中金属铜、铁含量测定法旋转圆盘电极发射光谱法

Method for Determination of Copper and Iron Content in Mineral Insulating Oil Rotating Disk Electrode Emission Spectrometry

DL/T 1498.3-2016 变电设备在线监测装置技术规范 第3部分:电容型设备及金属氧化物避雷器绝缘在线监测装置

本部分规定了电容型设备及金属氧化物避雷器绝缘在线监测装置的术语和定义、技术要求、试验项目及要求、检验规则，以及标志、包装、运输和贮存。 本部分适用于电容型设备绝缘在线监测装置和金属氧化物避雷器绝缘在线监测装置。

Technical specification for on-line monitoring device of transformation equipment.Part 3: On-line insulation monitoring device of capacitive equipment and metal-oxide surge arrester

DL/T 1498.1-2016 变电设备在线监测装置技术规范 第1部分：通则

本部分规定了变电设备在线监测装置装置的技术要求，试验，检验规则，标志、包装、运输和贮存等。 本部分适用于变压器、电抗器、断路器、气体绝缘金属封闭开关设备(GIS)、电容型设备、金属氧化物避雷器等变电设备的在线监测装置，其他在线监测装置可参照执行。

Technical specification for on-line monitoring device of transformation equipment.Part 1: general technical specification