31.100 电子管 标准查询与下载

GSO IEC 60235-2B:2014 附录 B 微波管电气特性的测量 第2部分：一般测量

Covers general measurements for all devices and for oscillator devices concerning pulse characteristics, pulse jitter, power hysteresis.

Supplement B - Measurement of the electrical properties of microwave tubes - Part 2: General measurements

GSO IEC 60235-4:2014 微波管电性能的测量 第4部分：磁控管（磁性保险丝）

Gives general requirements and precautions which apply when making measurements on magnetrons.

Measurement of the electrical properties of microwave tubes. Part 4: Magnetrons

GSO IEC 60151-19:2014 电子管和阀门的电性能计 第19部分：电晕稳定器的测量方法

This Recommendation is based on current practice on the measurement of corona stabilizers. It should not be regarded as a Recommendation in the sense of a standard, because a more detailed description of the measuring methods is needed if measuring results on the basis of these principles have to be comparable within definite tolerances.

Measurements of the electrical properties of electronic tubes and valves - Part 19: Methods of measurement on corona stabilizers

GSO IEC 60235-5:2014 微波管电性能的测量 第5部分：低功率速调管振荡器

Gives general requirements and precautions which apply when making measurements on low-power oscillator klystrons.

Measurement of the electrical properties of microwave tubes. Part 5: Low-power oscillator klystrons

GSO IEC 60151-6:2014 电子管和阀门的电气性能测量仪 第6部分：对电子管、电子管施加机械冲击激励（推力）的方法

This document outlines methods of application of mechanical shock (impulse) excitation to electronic tubes and valves. The methods are based on current practice of the application of shock. The document should not be regarded as a Recommendation in the sense of a standard because a more detailed description of the equipment is needed if measuring results are to be comparable within definite tolerances.

Measurements of the electrical properties of electronic tubes and valves. Part 6: Methods of application of mechanical shock (impulse) excitation to electronic tubes and valves

GSO IEC 60151-4:2014 电子管、阀门电性能表 第4部分：噪声系数测量方法

This document is based on current practice on the measurement of noise factor. It should not be regarded as a recommendation in the sense of a standard because a more detailed description of the measuring methods is needed if measuring results on the basis of these principles have to be comparable within definite tolerances.

Measurements of the electrical properties of electronic tubes and valves - Part 4: Methods of measuring noise factor

GSO IEC 60151-1:2014 电子管、阀门电性能表 第1部分：电极电流表

This document outlines conditions to be followed when measuring electrode current. It does not include measuring methods.

Measurements of the electrical properties of electronic tubes and valves - Part 1: Measurement of electrode current

GSO IEC 60100:2014 电子管、电子管电极间直接电容测量方法

This recommendation covers the measurement of direct interelectrode capacitances of tubes and valves within the conditions outlined in Clause 4 for the following classes: Receiving tubes and valves Cathode-ray tubes Gas tubes and gas-filled v alves Phototubes, photocells and multiplier types High-power vacuum tubes and valves

Methods for the measurement of direct interelectrode capacitances of electronic tubes and valves

GSO IEC 60151-0:2014 电子管、阀门电性能测量仪 第0部分：电子管、阀门测量方法注意事项

This general section on common aspects of measurement lists the general precautions to be taken, unless otherwise stated, to ensure reliability of measurements and should be read in conjunction with the separate sections describing methods of measurement. These separate sections contain the following items: a) Terms and definitions supplementing the International Electrotechnical Vocabulary. b) A sufficient amount of basic theory. c) Basic circuits. d) Measuring conditions and precautions. In case of conflict between the precautions given in this Recommendation and those given in the separate sections, the latter will prevail.

Measurements of the electrical properties of electronic tubes and valves - Part 0: Precautions relating to methods of measurement of electronic tubes and valves

GSO IEC 60151-28:2014 电子管电性能表 第28部分：彩色电视显像管测量方法

This standard deals only with the methods of measurement for colour television picture tubes with three electron beams and shadow mask.

Measurements of the electrical properties of electronic tubes - Part 28: Methods of measurement of colour television picture tubes

GSO IEC 60151-20:2014 电子管和阀门电性能表 第20部分：闸流管脉冲积分器的测量方法

This Recommendation is based on current practice on the measurement of thyratron pulse modulators. It should not be regarded as a Recommendation in the sense of a standard, because a more detailed description of the measuring methods is needed if measuring results on the basis of these principles have to be comparable within definite tolerances.

Measurements of the electrical properties of electronic tubes and valves. Part 20: Methods of measurement of thyratron pulse modulators

GSO IEC 60235-3:2014 微波管电性能的测量 第3部分：防漏盘管

Deals with the basic theory and measurements for disk seal tubes.

Measurement of the electrical properties of microwave tubes. Part 3: Disk seal tubes

GSO IEC 60151-25:2014 电子管的电等距 第25部分：盖革 米勒计数管的测量方法

This Recommendation provides terms, definitions, basic theory, recommended methods of measurement and mechanical data for Geiger-Müller counter tubes.

Measurements of the electrical properties of electronic tubes - Part 25: Methods of measurement of Geiger-Müller counter tubes

GSO IEC 60151-24:2014 电子管和阀门的电性能计 第24部分：阴极射线管存储电荷的测量方法

This Recommendation provides terms, definitions, basic theory and recommended methods of measurement for cathode-ray charge-storage tubes.

Measurements of the electrical properties of electronic tubes and valves - Part 24: Methods of measurement of cathode-ray charge-storage tubes

GSO IEC 60235-2:2014 微波管电性能的测量 第2部分：一般测量

Gives general requirements and precautions which apply when making measurements of the electrical properties of microwave tubes. It deals also with general methods of measurement for all devices for oscillator devices and for amplifier tubes.

Measurement of the electrical properties of microwave tubes - Part 2: General measurements

GSO IEC 60151-2:2014 电子管和阀门的电气性能计 第2部分：加热器或灯丝电流的测量

This document outlines conditions to be followed when measuring heater or filament current. It does not include measuring methods.

Measurements of the electrical properties of electronic tubes and valves - Part 2: Measurement of heater or filament current

GSO IEC 60151-15:2014 电子管和阀门静电计 第15部分：杂散和不需要的电极电流的测量方法

This Recommendation is based on current practice on the measurement of spurious and unwanted electrode currents. It should not be regarded as a Recommendation in the sense of a standard, because a more detailed description of the measuring methods is needed if measuring results on the basis of these principles have to be comparable within definite tolerances. This Recommendation does not apply to gasfilled tubes or valves.

Measurements of the electrical properties of electronic tubes and valves. Part 15: Methods of measurement of spurious and unwanted electrode currents

GSO IEC 60235-7:2014 微波管电性能的测量 第7部分：充气微波分离和耦合装置

Gives general requirements which apply when making measurements on gas-filled microwave switching devices.

Measurement of the electrical properties of microwave tubes. Part 7: Gas-filled microwave switching devices

GSO IEC 60139:2014 准备阴极射线管及其组件、连接和测量的总图纸

This International Standard gives guidance on the preparation of outline drawings of cathoderay tubes (CRTs), tube components, tube sub-assemblies and ancillary components with the object of encouraging the same practice when publications are prepared in different countries. These recommendations are contained in the specimen drawings, descriptive text and in the tables of required dimensions.

Preparation of outline drawings for cathode-ray tubes, their components, connections and gauges

GSO IEC 60151-8:2014 电子管和阀门电性能的测量 第8部分：阴极加热时间和加热器预热时间的测量

This Recommendation is based on current practice of the measurement of cathode heating time and heater warm-up time. It should not be regarded as a Recommendation in the sense of a standard, because a more detailed description of the measuring methods is needed if measuring results on the basis of these principles have to be comparable within definite tolerances. Modifications of detail may be made to the circuits described provided they do not change either the principle of measurement or the degree of refinement of the circuit. Any change made should maintain the required correlation of the measuring results.

Measurements of the electrical properties of electronic tubes and valves - Part 8: Measurement of cathode heating time and heater warm-up time