共找到 800 条与 光纤系统综合 相关的标准,共 54 页
What is BS EN IEC 62496 ‑ 4 ‑ 214 about? BS EN IEC 62496 is a series on optical circuit boards. BS EN IEC 62496 ‑ 4 ‑ 214 defines the standard interface dimensions for a terminated waveguide optical circuit board (OCB) assembly using single-row thirty-two-channel connectors for polymer waveguides connected with asymmetric PMT connector. BS EN IEC 62496
Optical circuit boards - Interface standards. Terminated waveguide OCB assembly using a single-row thirty-two-channel symmetric PMT connector
Fibre-optic communication subsystem test procedures - Part 4-5: Installed cabling plant - Attenuation measurement of MPO terminated fibre optic cabling plant using test equipment with MPO interfaces
IEC 62496-4-214: 2020 defines the standard interface dimensions for a terminated waveguide optical circuit board (OCB) assembly (referred to simply as "assembly") using single-row thirty-two-channel connectors for polymer waveguides connected with a symmetric PMT connector.
Optical circuit boards - Part 4-214: Interface standards - Terminated waveguide OCB assembly using a single-row thirty-two-channel symmetric PMT connector
Fibre optics - Multimode launch conditions - Part 1: Launch condition requirements for measuring multimode attenuation
Optical circuit boards - Part 4-214: Interface standards - Terminated waveguide OCB assembly using a single-row thirty-two-channel symmetric PMT connector
Amendment 5 - International Electrotechnical Vocabulary (IEV) - Part 731: Optical fibre communication
Intelligent optical distribution network intelligent access control technical requirements Part 1: Overall
50Gb/s PAM4 modulated optical transceiver module
100Gb/s QSFP28 optical transceiver module Part 5: 4×25Gb/s ER4 Lite
IP video optical transmission module
400Gb/s intensity modulated pluggable optical transceiver module Part 3: 4×100Gb/s
Parallel transmission active optical cable optical module Part 4: 200Gb/s AOC
100Gb/s QSFP28 optical transceiver module Part 4: 4×25Gb/s PSM4
200Gb/s intensity modulated optical transceiver module Part 1: 4×50Gb/s
Optical cable online monitoring OTDR module Part 1: for DWDM system
Fiber amplifier pump laser components for communications Part 2: 14xxnm pump laser components
IEC 61756-1:2019 covers general information on fibre management system interfaces. It includes the definitions and rules under which a fibre management system interface is created and it provides also criteria to identify the minimum bending radius for stored fibres. This document allows both single-mode and multimode fibre to be used. Liquid, gas or dust sealing requirements at the cable entry area or cable element ending are not covered in this document. This second edition cancels and replaces the first edition published in 2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - addition of figures to show the interface between protective housing and fibre management system; - addition of definitions for protective housing, closure, wall box, street cabinets and optical distribution frame modules; - addition of table with dimensions of fusion splice protectors and mechanical splices; - addition of method to identify the minimum bending radius for stored fibres; - addition of clause for other factors relevant to fibre management systems; - addition of annex A for example of calculating the minimum bending radius of stored fibres in a fibre management system. Keywords: fibre management system interfaces, minimum bending radius for stored fibres
Fibre optic interconnecting devices and passive components - Interface standard for fibre management systems - Part 1: General and guidance
Measuring methods of transmitting and/or receiving modules for middle and high speed fiber optic transmission
Technical requirements for low-power short-distance visible light communication
IEC 62343-2-1:2019 provides a reliability qualification test template for dynamic modules (DMs). The template describes the reliability qualification test items and provides information on requirements or options. Example test conditions are given for information purposes in Annex A. For reliability qualification purposes, some information about the internal components, parts and interconnections is needed. These internal parts are treated as black boxes. This document gives requirements for the evaluation of DM reliability by combining the reliability of such internal black boxes. The object of this reliability qualification test template is to provide a framework for the reliability qualification tests for DMs. Developers of reliability qualification tests for DMs determine the test conditions for each test item by referring to the examples in Annex A. Keywords: dynamic modules (DMs), test requirements for DMs
Dynamic modules - Part 2-1: Reliability qualification - Test template
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号