43.080.01 商用车辆综合 标准查询与下载

ISO 21308-3:2020 道路车辆 - 底盘和车身制造商之间的产品数据交换（BEP） - 第3部分:一般 大规模和管理交换参数

This document provides codes for the exchange of general, mass and administrative information between truck chassis manufacturers and bodywork manufacturers. The process of exchanging the above information can involve: — chassis manufacturer; — chassis importer; — chassis dealer; — one or more bodywork manufacturers; — bodywork component suppliers, e.g. manufacturers of demountable bodies, cranes and loading equipment, tipping equipment.

Road vehicles — Product data exchange between chassis and bodywork manufacturers (BEP) — Part 3: General, mass and administrative exchange parameters

ISO 21308-2:2020 道路车辆 - 底盘和车身制造商之间的产品数据交换（BEP） - 第2部分:车身交换参数

This document provides a set of codes for the exchange of dimensional data between truck chassis manufacturers and bodywork manufacturers. The process of exchanging the above information can involve: — chassis manufacturer; — chassis importer; — chassis dealer; — one or more bodywork manufacturers; and — bodywork component suppliers, e.g. manufacturers of demountable bodies, cranes and loading equipment, tipping equipment.

Road vehicles — Product data exchange between chassis and bodywork manufacturers (BEP) — Part 2: Dimensional bodywork exchange parameters

T/CSTE 0017-2020 氢燃料电池物流车运营管理规范

本标准规定了氢燃料电池物流车运营管理规范的术语和定义、一般要求、停车场管理、车辆管理、人员要求、作业要求和安全管理。 本标准适用于压缩氢系统的额定工作压力不大于35 MPa的氢燃料电池物流车（以下简称“车辆”）的运营管理。

Operation Specification for Hydrogen Fuel Cell Logistics Van

T/GDCKCJH 020-2020 电动汽车用动力电池复合动态工况下能效及电量估算测试方法

本标准规定了电动汽车动力蓄电池的复合动态工况模拟下能效及电量估算要求、试验方法和检验规则。 本标准适用于装载在电动汽车上的动力蓄电池。

Test methods for energy efficiency and power estimation of traction battery of electric vehicle under compound dynamic conditions

T/GDCKCJH 018-2020 电动汽车用动力电池管理系统功能安全评价技术

本标准规定了电动汽车用蓄电池管理系统功能评价的术语与定义、评估技术原则要求、评估流程与方法、评判标准。

Functional safety evaluation technology of power battery management system for electric vehicles

T/GDCKCJH 019-2020 电动汽车用动力电池系统热失控测试方法

本标准规定了电动汽车用锂离子动力电池系统热失控测试相关的术语、定义和测试方法。 本标准适用于电动汽车用锂离子动力电池系统热失控的测试。

Test method for thermal runaway of power battery systems for electric vehicles

T/CSAE 135-2020 商用车整车大气暴露试验评价方法

本标准规定了商用车整车大气暴露试验老化评级通则，其中包括油漆涂层件、塑料件、橡胶件、织物件、皮革件、镀层件以及无涂镀层金属件共7类零部件的单项老化评级方法以及整车的老化等级评价方法。 本标准适用于商用车大气曝晒试验，用于指导商用车整车大气老化评价。

Commercial vehicle assessment method of exposure to natural weathering

T/CSAE 126-2020 重型商用车发动机测试工况

本标准规定了商用车发动机进行排放和油耗试验时使用的测试工况。 

Engine test cycle for heavy-duty commercial vehicles

BS ISO 19585:2019 重型商用车和公共汽车 车辆动力学仿真和验证 稳态循环驾驶行为

What is ISO 19585 - Vehicle dynamics simulation and validation about?    ISO 19585 is an international standard on heavy commercial vehicles and buses that discusses the task of evaluating the dynamic behaviour.   ISO 19585 specifies a method for comparing simulation results from a vehicle model to measured test data for an existing vehicle according to steady-state circular driving tests. The comparison is made for the purpose of validating the vehicle model for this type of test.   NOTE: ISO 19585 applies to heavy vehicles, including commercial vehicles, commercial vehicle combinations, buses and articulated buses as defined in ISO 3833 (trucks and trailers with a maximum weight above 3,5 tonnes and buses and articulated buses with a maximum weight above 5 tonnes, according to ECE and EC vehicle classification, categories M3, N2, N3, O3 and O4).

Heavy commercial vehicles and buses. Vehicle dynamics simulation and validation. Steady-state circular driving behavior

BS ISO 19586:2019 重型商用车和公共汽车 车辆动力学仿真和验证 车辆组合的横向动态稳定性

What is ISO 19586- Vehicle dynamics simulation and validation about?    ISO 19586 is an international standard on heavy commercial vehicles and buses that discusses the task of evaluating the dynamic behaviour.   ISO 19586 specifies a method for comparing simulation results from a vehicle model to measured test data for an existing vehicle combination’s lateral stability according to driving tests. The comparison is made for the purpose of validating the simulation model for this type of test. A complete validation comprises the comparison for at least one tested vehicle and one variant of this vehicle, covered by a parameter variation in the vehicle model.   NOTE: ISO 19586 applies to heavy vehicles, including commercial vehicles, commercial vehicle combinations, buses and articulated buses (trucks and trailers with a maximum weight above 3,5 tonnes and buses and articulated buses with a maximum weight above 5 tonnes, according to ECE and EC vehicle classification, categories M3, N2, N3, O3 and O4).   Who is ISO 19586 - Vehicle dynamics simulation and validation

Heavy commercial vehicles and buses. Vehicle dynamics simulation and validation. Lateral dynamic stability of vehicle combinations

ISO 19585:2019 重型商业车辆和公共汽车 - 车辆动力学模拟和验证 - 稳态循环驾驶行为

This document specifies a method for comparing simulation results from a vehicle model to measured test data for an existing vehicle according to steady-state circular driving tests as specified in ISO 14792. The comparison is made for the purpose of validating the vehicle model for this type of test. This document applies to heavy vehicles, including commercial vehicles, commercial vehicle combinations, buses and articulated buses as defined in ISO 3833 (trucks and trailers with a maximum weight above 3,5 tonnes and buses and articulated buses with a maximum weight above 5 tonnes, according to ECE and EC vehicle classification, categories M3, N2, N3, O3 and O4).

Heavy commercial vehicles and buses — Vehicle dynamics simulation and validation — Steady-state circular driving behavior

ISO 19586:2019 重型商用车辆和公共汽车.车辆动力学模拟和验证.车辆组合的横向动态稳定性

This document specifies a method for comparing simulation results from a vehicle model to measured test data for an existing vehicle combination’s lateral stability according to driving tests as specified in test. A complete validation comprises the comparison for at least one tested vehicle and one variant of this vehicle, covered by a parameter variation in the vehicle model. The document applies to heavy vehicles, including commercial vehicles, commercial vehicle combinations, buses and articulated buses as defined in ISO 3833 (trucks and trailers with maximum weight above 3,5 tonnes and buses and articulated buses with maximum weight above 5 tonnes, according to ECE and EC vehicle classification, categories M3, N2, N3, O3 and O4).

Heavy commercial vehicles and buses — Vehicle dynamics simulation and validation — Lateral dynamic stability of vehicle combinations

T/CICE 01-2019 商用车检测维修职业能力评价规范

       本标准按照GB/T 1.1—2009给出的规则起草。具体内容主要包括以下几个部分：       S1 职业素养与安全、S2 点燃式发动机、S3  柴油发动机、S4  传动系统、S5  制动系统、S6  悬架与转向系统 、S7 车身电子系统、S8空调与制暖系统、S9 整车保养与维护、S10电动商用车。        

Professional competence evaluation of commercial vehicle inspection and maintenance

T/GHDQ 40-2019 高寒地区纯电动轻型卡车技术条件

主要补充制定了纯电动轻型卡车在-40℃温度下的性能指标。

Technical Conditions of Battery Electric Light Truck in Frigid Regions

T/GHDQ 33-2019 高寒地区智能网联商用车自动紧急制动系统技术条件

主要补充制定商用车自动紧急制动系统（AEB）在-40℃温度下的技术条件。

Technical Conditions of Autonomous Emergency Braking System of Intelligent Network Passenger Car in Frigid Regions

T/GHDQ 34-2019 高寒地区智能网联半挂牵引车全速范围自适应巡航控制系统（FSRA）技术条件

主要补充制定半挂牵引车全速范围自适应巡航控制系统(FSRA)在-40℃温度下的技术条件。

Full speed range adaptive cruise control (FSRA) system of intelligent connected semi-trailer towing vehicle in frigid regions for performance requirements

T/GHDQ 41-2019 纯电动轻型卡车高寒性能综合评价指数

主要规定了纯电动轻型卡车高寒性能综合评价指数。

Comprehensive Evaluation Index on the Performance of the Battery Electric Light Truck in Frigid Regions

BS ISO 19380:2019 重型商用车和公共汽车 重心测量 轴升、倾斜台和稳定摆测试方法

What is ISO 19380 - Centre of gravity measurements of vehicles and buses about?    ISO 19380 is an international standard on heavy commercial vehicles and buses that are presented for measuring the location of the centre of gravity of an individual vehicle unit in the horizontal, lateral and vertical planes.   ISO 19380 describes a standard method for measuring a vehicle’s longitudinal and lateral (horizontal plane) centre of gravity (CG) positions and three methods for estimating a vehicle’s vertical CG position, the axle lift, tilt-table, and stable pendulum methods.   NOTE: ISO 19380 applies to heavy vehicles, that is commercial vehicles and buses as defined in ISO 3833 (trucks and trailers with a maximum weight above 3,5 tonnes and buses and articulated buses with a maximum weight above 5 tonnes, according to ECE and EC vehicle classification, categories M3, N2, N3, O3 and O4). CG measurements are performed separately for each single unit. 

Heavy commercial vehicles and buses. Centre of gravity measurements. Axle lift, tilt-table and stable pendulum test methods

ISO 19380:2019 重型商用车辆和公共汽车.重心测量.倾斜台轴提升和稳定摆试验方法

This document describes a standard method for measuring a vehicle’s longitudinal and lateral (horizontal plane) centre of gravity (CG) positions and three methods for estimating a vehicle’s vertical CG position, the axle lift, tilt-table, and stable pendulum methods. It applies to heavy vehicles, that is commercial vehicles and buses as defined in ISO 3833 (trucks and trailers with maximum weight above 3,5 tonnes and buses and articulated buses with maximum weight above 5 tonnes, according to ECE and EC vehicle classification, categories M3, N2, N3, O3 and O4). CG measurements are performed separately for each single unit.

Heavy commercial vehicles and buses — Centre of gravity measurements — Axle lift, tilt-table and stable pendulum test methods

KS R ISO 7656-2019 商用道路车辆 尺寸代码

Commercial road vehicles－Dimensional codes