59.100.10 纺织玻璃纤维材料 标准查询与下载
共找到 572 条与 纺织玻璃纤维材料 相关的标准，共 39 页
This part of ISO 3597 provides general information and specifies a method for preparing specimens (rods) intended to be used for tests specified in the other parts of ISO 3597.
Textile-glass-reinforced plastics -- Determination of mechanical properties on rods made of roving-reinforced resin -- Part 1: General considerations and preparation of rods
- ICS
- 59.100.10
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard specifies a method for determining the twist balance index of folded yarn and cabled yarn made from textile glass, carbon, aramid or any other reinforcement fibre.
Reinforcement yarns -- Determination of twist balance index
- ICS
- 59.100.10
- CCS
- 发布
- 2015-09-03
- 实施
This part of ISO 3597 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin. The test may be carried out on “as-moulded” rods, or on rods that have been pretreated by immersion in boiling water (or another medium) for a specified time. The test is intended for inspection and quality control of rovings or for evaluating their suitability for use in a resin system. The results obtained are not intended for the generation of design data.
Textile-glass-reinforced plastics -- Determination of mechanical properties on rods made of roving-reinforced resin -- Part 2: Determination of flexural strength
- ICS
- 59.100.10
- CCS
- 发布
- 2015-09-03
- 实施
1.1 This International Standard specifies a method for the determination of the tensile breaking force and elongation at break of glass yarns taken from packages. 1.2 The method is applicable to various types of glass yarn (single, folded, cabled, strands, structures without twist, rovings, etc.). It is basically intended for single, folded and cabled glass yarns having a diameter of less than 2 mm, or a linear density lower than 2000 tex, taken from packages. Heavier yarns may be also tested providing the test conditions are acceptable to all interested parties. 1.3 The method is not applicable to glass yarns which, in equilibrium with the standard atmosphere and under a pre-tension of 5 mN/tex, are elongated by more than 0,5 %. Such yarns can be tested using a lower pre-tension (for example 2,5 mN/tex or 1 mN/tex), acceptable to all interested parties. This would occur mainly when dealing with staple-fibre yarns. NOTE 1 Though the determination may be run on beamed yarn or on yarns taken from fabrics, the results must be considered as indicative only. NOTE 2 This test method is primarily intended for material characterization and quality control. Fibre-to-fibre abrasion and other factors such as insufficiently uniform tension (catenary) will increase variability and generate low test values. This will consequently impede accurate correlation between performance of the yarns and end use applications. Extreme care should be taken in considering this method for specification purposes. NOTE 3 Though this International Standard provides the possibility of determining the elongation at break, this practice is not recommended, however. Indeed, a correct assessment of the elongation will only be obtained using an extensometer; it will not be obtained by measuring the distance traversed by the moving clamp. On the other hand, experience shows that the use of an extensometer is quite delicate and often causes damage to the specimen.
Textile glass -- Yarns -- Determination of breaking force and breaking elongation
- ICS
- 59.100.10
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard specifies a method for the determination of the stiffness of textile glass rovings.
Textile glass -- Determination of stiffness of rovings
- ICS
- 59.100.10
- CCS
- 发布
- 2015-09-03
- 实施
This International Standard specifies a method for the determination of the tensile breaking force of textile glass mats. The method is intended for chopped-strand mat but is equally applicable to certain types of continuous-strand mat usually intended for pultrusion.
Textile glass -- Mats -- Determination of tensile breaking force
- ICS
- 59.100.10
- CCS
- 发布
- 2015-09-03
- 实施
本标准规定了风电用玻璃纤维直接无捻粗纱（简称：风电用纱）的定义、标记、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于玻璃纤维原丝直接拉制而成，不经过络纱的风电用玻璃纤维直接无捻粗纱。
Glass fiber direct roving for wind power
- ICS
- 59.100.10
- CCS
- C3061
- 发布
- 2015-08-17
- 实施
- 2017-03-06
本标准适用于以增强玻璃纤维网格布为主要材料，经过酚醛树脂或环氧树脂浸渍后烘干、裁切、热压固化成型的玻璃纤维网盖。主要用作砂页盘等表面抛光磨具的增强基体、底托等。
Fiberglass backing plate
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2015-07-14
- 实施
- 2016-01-01
1.1 This specification primarily covers greige tapes and webbings woven from “E” electrical classification glass fiber yarns. This specification can also be applied to tapes and webbings made of other glass fiber grades upon agreement between the purchaser and the supplier. 1.2 This specification is intended to assist ultimate users by designating the types of these products that are typical in the industry. This specification permits the application of organic materials to the glass fiber yarn during manufacture that helps facilitate weaving. When used as permitted in this specification, such materials will not interfere with the intended end use requirements. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Greige Woven Glass Tapes and Webbings
- ICS
- 59.100.10
- CCS
- 发布
- 2015
- 实施
1.1 This specification covers the requirements for continuous glass filament sewing thread; and continuous filament cord, untreated and neoprene treated. 1.2 This specification is intended to assist ultimate users by designating the types of these products that are typical in the industry. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Glass Fiber Cord and Sewing Thread
- ICS
- 59.100.10
- CCS
- 发布
- 2015
- 实施
Dielectric fabrics made of glass twisted complex threads. Specifications
- ICS
- 59.100.10
- CCS
- Q33
- 发布
- 2015
- 实施
- 2016-06-01
Textile glass. Determination of stiffness of roving
- ICS
- 59.100.10
- CCS
- Q33
- 发布
- 2015
- 实施
- 2016-06-01
Textile glass. Complex twisted threads. Specifications
- ICS
- 59.100.10
- CCS
- Q33
- 发布
- 2015
- 实施
- 2016-06-01
Glass textile materials. Method for determination of moisture and substances removed during calcination
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2015
- 实施
- 2016-06-01
Textile glass materials. Method for determination of breaking load and elongation at break
- ICS
- 59.100.10
- CCS
- Q33
- 发布
- 2015
- 实施
- 2016-06-01
Unidirectional glass threads. Specifications
- ICS
- 59.100.10
- CCS
- J05
- 发布
- 2015
- 实施
- 2016-06-01
Glass textile products. Methods for determination of filaments and fibre diameter
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2015
- 实施
- 2016-06-01
This International Standard provides a basis for a specification applicable to textured yarns made from single or folded yarns of textile glass. Textured glass yarns can be produced by several types of process. They can be made starting either from a single strand or from two or more strands in which one or more have been “opened” to give the “bulky” aspect of textured yarn. Textured glass yarn is used in various applications, for example insulation, filtration, the manufacture of decorative textiles, the reinforcement of plastics and the manufacture of packing materials.
Textile glass -- Textured yarns -- Basis for a specification
- ICS
- 59.100.10
- CCS
- 发布
- 2014-12-25
- 实施
This International Standard provides a basis for a specification applicable to textile glass yarns strands, slivers, single yarns, folded yarns and cable yarns. It does not apply to textured yarns, rovings, chopped strands, milled fibres, pre-impregnated yarns, etc. This International Standard does not cover all requirements for specialized applications. Where such other requirements are necessary, they are, or will be, given in other appropriate International Standards.
Textile glass -- Yarns -- Basis for a specification
- ICS
- 59.100.10
- CCS
- 发布
- 2014-12-25
- 实施
This International Standard specifies a method for the determination of the average thickness, the thickness under load and the recovery after compression of chopped-strand and continuous-filament textile-glass mats.
Textile glass -- Chopped-strand and continuous-filament mats -- Determination of average thickness, thickness under load and recovery after compression
- ICS
- 59.100.10
- CCS
- 发布
- 2014-12-25
- 实施
